On Wed, Aug 27, 2014 at 03:48:27PM +0100, Ajay Kumar wrote:
> Add DT nodes for ptn3460 bridge chip and panel.
> Add backlight enable pin and backlight power supply for pwm-backlight.
> Also add bridge phandle needed by dp to enable display on snow.
>
> Note that, snow doesn't support "chunghwa,claa101wb01" panel,
> but still we choose to reuse the binding since "chunghwa,claa101wb01"
> has similar LCD timings.
What does it actually have?
It's fine to have "chunghwa,claa101wb01" as a fallback but we should
have an identifier for the actual display, too.
Thanks,
Mark.
> Signed-off-by: Ajay Kumar <ajaykumar.rs@xxxxxxxxxxx>
> ---
> Changes since V1:
> -- Remove "simple-panel" compatible string.
> -- Use GPIO_ACTIVE_HIGH instead of 0.
> -- Change panel node naming from "panel-simple" to "panel".
>
> arch/arm/boot/dts/exynos5250-snow.dts | 41 ++++++++++++++++++---------------
> 1 file changed, 22 insertions(+), 19 deletions(-)
>
> diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
> index f2b8c41..1ac9709 100644
> --- a/arch/arm/boot/dts/exynos5250-snow.dts
> +++ b/arch/arm/boot/dts/exynos5250-snow.dts
> @@ -9,6 +9,7 @@
> */
>
> /dts-v1/;
> +#include <dt-bindings/gpio/gpio.h>
> #include "exynos5250.dtsi"
> #include "exynos5250-cros-common.dtsi"
>
> @@ -181,7 +182,7 @@
> dcdc3 {
> ti,enable-ext-control;
> };
> - fet1 {
> + fet1: fet1 {
> regulator-name = "vcd_led";
> ti,overcurrent-wait = <3>;
> };
> @@ -204,7 +205,7 @@
> regulator-always-on;
> ti,overcurrent-wait = <3>;
> };
> - fet6 {
> + fet6: fet6 {
> regulator-name = "lcd_vdd";
> ti,overcurrent-wait = <3>;
> };
> @@ -253,6 +254,15 @@
> pinctrl-0 = <&max98095_en>;
> pinctrl-names = "default";
> };
> +
> + ptn3460: lvds-bridge@20 {
> + compatible = "nxp,ptn3460";
> + reg = <0x20>;
> + powerdown-gpios = <&gpy2 5 GPIO_ACTIVE_HIGH>;
> + reset-gpios = <&gpx1 5 GPIO_ACTIVE_HIGH>;
> + edid-emulation = <5>;
> + panel = <&panel>;
> + };
> };
>
> i2s0: i2s@03830000 {
> @@ -300,11 +310,13 @@
> vdd_pll-supply = <&ldo8_reg>;
> };
>
> - backlight {
> + backlight: backlight {
> compatible = "pwm-backlight";
> pwms = <&pwm 0 1000000 0>;
> brightness-levels = <0 100 500 1000 1500 2000 2500 2800>;
> default-brightness-level = <7>;
> + enable-gpios = <&gpx3 0 GPIO_ACTIVE_HIGH>;
> + power-supply = <&fet1>;
> pinctrl-0 = <&pwm0_out>;
> pinctrl-names = "default";
> };
> @@ -314,6 +326,12 @@
> samsung,invert-vclk;
> };
>
> + panel: panel {
> + compatible = "chunghwa,claa101wb01";
> + power-supply = <&fet6>;
> + backlight = <&backlight>;
> + };
> +
> dp-controller@145B0000 {
> status = "okay";
> pinctrl-names = "default";
> @@ -325,22 +343,7 @@
> samsung,link-rate = <0x0a>;
> samsung,lane-count = <2>;
> samsung,hpd-gpio = <&gpx0 7 0>;
> -
> - display-timings {
> - native-mode = <&timing1>;
> -
> - timing1: timing@1 {
> - clock-frequency = <70589280>;
> - hactive = <1366>;
> - vactive = <768>;
> - hfront-porch = <40>;
> - hback-porch = <40>;
> - hsync-len = <32>;
> - vback-porch = <10>;
> - vfront-porch = <12>;
> - vsync-len = <6>;
> - };
> - };
> + bridge = <&ptn3460>;
> };
> };
>
> --
> 1.7.9.5
>
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
