Hi,
over years couple of drivers were upstream and it is time to sync it up.
On the top of it also adding new Kria boards which are using new overlay
infrastructure which check if that overlays can be applied to base DT file.
Thanks,
Michal
Changes in v2:
- Add reviewed-by from Laurent
- New patch in the series
- New patch in the series
- Use sugar syntax - reported by Geert
- Update copyright years
- Fix SD3.0 comment alignment
- Remove one newline from Makefile
Amit Kumar Mahapatra (1):
arm64: zynqmp: Do not duplicate flash partition label property
Michal Simek (29):
arm64: zynqmp: Disable CCI by default
arm64: zynqmp: Enable fpd_dma for zcu104 platforms
arm64: zynqmp: Fix irps5401 device nodes
arm64: zynqmp: Add pinctrl description for all boards
arm64: zynqmp: Correct zcu111 psgtr description
arm64: zynqmp: Wire psgtr for zc1751-xm015
arm64: zynqmp: Correct psgtr description for zcu100-revC
arm64: zynqmp: Add phy description for usb3.0
arm64: zynqmp: Disable WP on zcu111
arm64: zynqmp: Add missing mio-bank properties to dc1 and dc5
arm64: zynqmp: Wire DP and DPDMA for dc1/dc4
arm64: zynqmp: Enable nand driver for dc2 and dc3
arm64: zynqmp: Remove additional newline
arm64: zynqmp: Move clock node to zynqmp-clk-ccf.dtsi
arm64: zynqmp: Add nvmem alises for eeproms
arm64: zynqmp: List reset property for ethernet phy
arm64: zynqmp: Remove can aliases from zc1751
arm64: zynqmp: Move DP nodes to the end of file on zcu106
arm64: zynqmp: Add note about UHS mode on some boards
arm64: zynqmp: Remove information about dma clock on zcu106
arm64: zynqmp: Wire qspi on multiple boards
arm64: zynqmp: Move rtc to different location on zcu104-revA
arm64: zynqmp: Add reset description for sata
arm64: zynqmp: Sync psgtr node location with zcu104-revA
arm64: zynqmp: Remove description for 8T49N287 and si5382 chips
arm64: zynqmp: Add support for zcu102-rev1.1 board
arm64: zynqmp: Enable xlnx,zynqmp-dwc3 driver for xilinx boards
arm64: zynqmp: Add psgtr description to zc1751 dc1 board
arm64: zynqmp: Add support for Xilinx Kria SOM board
Mounika Grace Akula (1):
arm64: zynqmp: Add reset-on-timeout to all boards and modify default
timeout value
Srinivas Neeli (1):
arm64: zynqmp: Update rtc calibration value
Stefano Stabellini (1):
arm64: zynqmp: Add missing SMID for pcie to zynqmp.dtsi
.../devicetree/bindings/arm/xilinx.yaml | 32 ++
arch/arm64/boot/dts/xilinx/Makefile | 11 +
.../arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi | 13 +-
.../boot/dts/xilinx/zynqmp-sck-kv-g-revA.dts | 335 +++++++++++++++++
.../boot/dts/xilinx/zynqmp-sck-kv-g-revB.dts | 318 ++++++++++++++++
.../boot/dts/xilinx/zynqmp-sm-k26-revA.dts | 289 +++++++++++++++
.../boot/dts/xilinx/zynqmp-smk-k26-revA.dts | 21 ++
.../boot/dts/xilinx/zynqmp-zc1232-revA.dts | 16 +-
.../boot/dts/xilinx/zynqmp-zc1254-revA.dts | 16 +-
.../dts/xilinx/zynqmp-zc1751-xm015-dc1.dts | 298 ++++++++++++++-
.../dts/xilinx/zynqmp-zc1751-xm016-dc2.dts | 342 +++++++++++++++++-
.../dts/xilinx/zynqmp-zc1751-xm017-dc3.dts | 23 +-
.../dts/xilinx/zynqmp-zc1751-xm018-dc4.dts | 24 +-
.../dts/xilinx/zynqmp-zc1751-xm019-dc5.dts | 330 ++++++++++++++++-
.../boot/dts/xilinx/zynqmp-zcu100-revC.dts | 264 +++++++++++++-
.../boot/dts/xilinx/zynqmp-zcu102-rev1.1.dts | 15 +
.../boot/dts/xilinx/zynqmp-zcu102-revA.dts | 321 +++++++++++++++-
.../boot/dts/xilinx/zynqmp-zcu102-revB.dts | 3 +-
.../boot/dts/xilinx/zynqmp-zcu104-revA.dts | 292 ++++++++++++++-
.../boot/dts/xilinx/zynqmp-zcu104-revC.dts | 250 ++++++++++++-
.../boot/dts/xilinx/zynqmp-zcu106-revA.dts | 341 ++++++++++++++++-
.../boot/dts/xilinx/zynqmp-zcu111-revA.dts | 275 +++++++++++++-
arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 99 +++--
23 files changed, 3833 insertions(+), 95 deletions(-)
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dts
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dts
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-sm-k26-revA.dts
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-smk-k26-revA.dts
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.1.dts
--
2.32.0
