On 6/14/21 5:25 PM, Michal Simek wrote: > Hi, > > over years couple of drivers were upstream and it is time to sync it up. > On the top of it also adding new Kria boards which are using new overlay > infrastructure which check if that overlays can be applied to base DT file. > > Thanks, > Michal > > Changes in v2: > - Add reviewed-by from Laurent > - New patch in the series > - New patch in the series > - Use sugar syntax - reported by Geert > - Update copyright years > - Fix SD3.0 comment alignment > - Remove one newline from Makefile > > Amit Kumar Mahapatra (1): > arm64: zynqmp: Do not duplicate flash partition label property > > Michal Simek (29): > arm64: zynqmp: Disable CCI by default > arm64: zynqmp: Enable fpd_dma for zcu104 platforms > arm64: zynqmp: Fix irps5401 device nodes > arm64: zynqmp: Add pinctrl description for all boards > arm64: zynqmp: Correct zcu111 psgtr description > arm64: zynqmp: Wire psgtr for zc1751-xm015 > arm64: zynqmp: Correct psgtr description for zcu100-revC > arm64: zynqmp: Add phy description for usb3.0 > arm64: zynqmp: Disable WP on zcu111 > arm64: zynqmp: Add missing mio-bank properties to dc1 and dc5 > arm64: zynqmp: Wire DP and DPDMA for dc1/dc4 > arm64: zynqmp: Enable nand driver for dc2 and dc3 > arm64: zynqmp: Remove additional newline > arm64: zynqmp: Move clock node to zynqmp-clk-ccf.dtsi > arm64: zynqmp: Add nvmem alises for eeproms > arm64: zynqmp: List reset property for ethernet phy > arm64: zynqmp: Remove can aliases from zc1751 > arm64: zynqmp: Move DP nodes to the end of file on zcu106 > arm64: zynqmp: Add note about UHS mode on some boards > arm64: zynqmp: Remove information about dma clock on zcu106 > arm64: zynqmp: Wire qspi on multiple boards > arm64: zynqmp: Move rtc to different location on zcu104-revA > arm64: zynqmp: Add reset description for sata > arm64: zynqmp: Sync psgtr node location with zcu104-revA > arm64: zynqmp: Remove description for 8T49N287 and si5382 chips > arm64: zynqmp: Add support for zcu102-rev1.1 board > arm64: zynqmp: Enable xlnx,zynqmp-dwc3 driver for xilinx boards > arm64: zynqmp: Add psgtr description to zc1751 dc1 board > arm64: zynqmp: Add support for Xilinx Kria SOM board > > Mounika Grace Akula (1): > arm64: zynqmp: Add reset-on-timeout to all boards and modify default > timeout value > > Srinivas Neeli (1): > arm64: zynqmp: Update rtc calibration value > > Stefano Stabellini (1): > arm64: zynqmp: Add missing SMID for pcie to zynqmp.dtsi > > .../devicetree/bindings/arm/xilinx.yaml | 32 ++ > arch/arm64/boot/dts/xilinx/Makefile | 11 + > .../arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi | 13 +- > .../boot/dts/xilinx/zynqmp-sck-kv-g-revA.dts | 335 +++++++++++++++++ > .../boot/dts/xilinx/zynqmp-sck-kv-g-revB.dts | 318 ++++++++++++++++ > .../boot/dts/xilinx/zynqmp-sm-k26-revA.dts | 289 +++++++++++++++ > .../boot/dts/xilinx/zynqmp-smk-k26-revA.dts | 21 ++ > .../boot/dts/xilinx/zynqmp-zc1232-revA.dts | 16 +- > .../boot/dts/xilinx/zynqmp-zc1254-revA.dts | 16 +- > .../dts/xilinx/zynqmp-zc1751-xm015-dc1.dts | 298 ++++++++++++++- > .../dts/xilinx/zynqmp-zc1751-xm016-dc2.dts | 342 +++++++++++++++++- > .../dts/xilinx/zynqmp-zc1751-xm017-dc3.dts | 23 +- > .../dts/xilinx/zynqmp-zc1751-xm018-dc4.dts | 24 +- > .../dts/xilinx/zynqmp-zc1751-xm019-dc5.dts | 330 ++++++++++++++++- > .../boot/dts/xilinx/zynqmp-zcu100-revC.dts | 264 +++++++++++++- > .../boot/dts/xilinx/zynqmp-zcu102-rev1.1.dts | 15 + > .../boot/dts/xilinx/zynqmp-zcu102-revA.dts | 321 +++++++++++++++- > .../boot/dts/xilinx/zynqmp-zcu102-revB.dts | 3 +- > .../boot/dts/xilinx/zynqmp-zcu104-revA.dts | 292 ++++++++++++++- > .../boot/dts/xilinx/zynqmp-zcu104-revC.dts | 250 ++++++++++++- > .../boot/dts/xilinx/zynqmp-zcu106-revA.dts | 341 ++++++++++++++++- > .../boot/dts/xilinx/zynqmp-zcu111-revA.dts | 275 +++++++++++++- > arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 99 +++-- > 23 files changed, 3833 insertions(+), 95 deletions(-) > create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dts > create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dts > create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-sm-k26-revA.dts > create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-smk-k26-revA.dts > create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.1.dts > Applied 1-30, 32. 31 and 33 requires newer version. Thanks, Michal -- Michal Simek, Ing. (M.Eng), OpenPGP -> KeyID: FE3D1F91 w: www.monstr.eu p: +42-0-721842854 Maintainer of Linux kernel - Xilinx Microblaze Maintainer of Linux kernel - Xilinx Zynq ARM and ZynqMP ARM64 SoCs U-Boot custodian - Xilinx Microblaze/Zynq/ZynqMP/Versal SoCs
