Em Thu, 9 Aug 2018 16:35:20 +0200
Marco Felsch <m.felsch@xxxxxxxxxxxxxx> escreveu:
> Hi Mauro,
>
> Thanks for your feedback.
> > > > > + dev_dbg(sd->dev, "link setup '%s':%d->'%s':%d[%d]",
> > > > > + remote->entity->name, remote->index, local->entity->name,
> > > > > + local->index, flags & MEDIA_LNK_FL_ENABLED);
> > > >
> > > > Hmm... the remote is the connector, right? I would switch the
> > > > print message to point from the connector to tvp5150, as this is
> > > > the signal flow.
> > >
> > > I don't know what you mean, I tought that's what I'm already do. If I
> > > change it it will print something like: tvp5150 2-005d :0 -> Comp0 :0[1]
> >
> > Hmm... then "local" actually means the connector and "remote"
> > is the tvp5150?
>
> Nope, local is the tvp and remote is the connector. Actual the output
> looks as follows
>
> [ 26.339939] tvp5150 2-005d: link setup 'Comp0':0->'tvp5150 2-005d':0[1]
> [ 26.346606] tvp5150 2-005d: Setting 0 active [composite]
>
> I think this is what you mean with '... point from the connector to
> tvp5150 ...'.
Yes.
>
> >
> > >
> > > >
> > > > Btw, it would likely be better to call it "connector" or "conn_entity",
> > > > to make it clearer.
> > >
> > > I tought remote is the common nomenclature. Also the remote mustn't be a
> > > connector. In my case it's a soldered camera. With this in mind, you think
> > > it should be still changed?
> >
> > I see your point.
> >
> > Yeah, remote is a common nomenclature. Yet, as it can be seen from
> > the above comment (and your answer), common nomenclature may lead
> > in to mistakes :-)
>
> Yeah, I know what you mean ^^
>
> >
> > It would be good to have either one of sides better named (either
> > the connectors side or the tvp5150 side - or both), in order to be
> > clearer and avoid confusion of someone else touches that part of
> > the code.
>
> Yes, I'm with you. Since the local always points to the tvp5150, I will
> change the local to tvp5150 or tvp5150_pad. Renaming the remote isn't
> that good since it can be anything.
OK!
>
> >
> > In this specific case, both connectors and tvp5150 are created by
> > the tvp5150, so both are "local" in the sense that both are
> > created by this driver.
> >
>
> I know.. Maybe there should be a 'common' svideo-/composite-connector
> code and some helpers to create and link those. Then we can drop the
> 'local' connectors.
Yeah, that could be a good idea.
> > > > > +static int tvp5150_registered(struct v4l2_subdev *sd)
> > > > > +{
> > > > > +#ifdef CONFIG_MEDIA_CONTROLLER
> > > > > + struct tvp5150 *decoder = to_tvp5150(sd);
> > > > > + unsigned int i;
> > > > > + int ret;
> > > > > +
> > > > > + for (i = 0; i < decoder->connectors_num; i++) {
> > > > > + struct media_entity *con = &decoder->connectors[i].ent;
> > > > > + struct media_pad *pad = &decoder->connectors[i].pad;
> > > > > + unsigned int port = decoder->connectors[i].port_num;
> > > > > + bool is_svideo = decoder->connectors[i].is_svideo;
> > > > > +
> > > > > + pad->flags = MEDIA_PAD_FL_SOURCE;
> > > > > + ret = media_entity_pads_init(con, 1, pad);
> > > > > + if (ret < 0)
> > > > > + return ret;
> > > > > +
> > > > > + ret = media_device_register_entity(sd->v4l2_dev->mdev, con);
> > > > > + if (ret < 0)
> > > > > + return ret;
> > > > > +
> > > > > + ret = media_create_pad_link(con, 0, &sd->entity, port, 0);
> > > > > + if (ret < 0) {
> > > > > + media_device_unregister_entity(con);
> > > > > + return ret;
> > > > > + }
> > > > > +
> > > > > + if (is_svideo) {
> > > > > + /* svideo links to both aip1a and aip1b */
> > > > > + ret = media_create_pad_link(con, 0, &sd->entity,
> > > > > + port + 1, 0);
> > > > > + if (ret < 0) {
> > > > > + media_device_unregister_entity(con);
> > > > > + return ret;
> > > > > + }
> > > > > + }
> > > > > +
> > > > > + }
> > > >
> > > > IMO, it should route to the first available connector.
> > >
> > > Did you mean to set the link status to enabled?
> >
> > Yes.
> >
> > > If so I have one
> > > question else can you tell me what you mean?
> > >
> > > Should I use the media_entity_setup_link() helper or should I mark it as
> > > enabled during media_create_pad_link()? Now I did something like:
> > >
> > > if (i == 0) {
> > > list_for_each_entry(link, &con->links, list) {
> > > media_entity_setup_link(link, MEDIA_LNK_FL_ENABLED);
> > > }
> > > }
> >
> > yeah, I guess this should work for both the cases where the first
> > connector is a comp or a svideo input.
> >
> > I would prefer coding it differently, e. g. something like:
> >
> >
> > for (i = 0; i < decoder->connectors_num; i++) {
> > int flags = i ? 0 : MEDIA_LNK_FL_ENABLED;
> >
> > and then use the flags var as the last argument for media_create_pad_link()
> > calls. That would avoid an extra loop and would likely reduce a little bit
> > the code size.
>
> Sorry for the ambiguous code example. I did the 'if (i == 0)' in the same
> loop, so no extra loop. I can do it your way, but than unnecessary
> media_entity_setup_link() are made.
I got that, but:
list_for_each_entry(link, &con->links, list) {
media_entity_setup_link(link, MEDIA_LNK_FL_ENABLED);
}
would be a second loop inside it :-)
What do you mean by an unnecessary media_entity_setup_link()?
What I was thinking is something like:
static int tvp5150_registered(struct v4l2_subdev *sd)
{
#ifdef CONFIG_MEDIA_CONTROLLER
struct tvp5150 *decoder = to_tvp5150(sd);
unsigned int i;
int ret;
for (i = 0; i < decoder->connectors_num; i++) {
struct media_entity *con = &decoder->connectors[i].ent;
struct media_pad *pad = &decoder->connectors[i].pad;
unsigned int port = decoder->connectors[i].port_num;
bool is_svideo = decoder->connectors[i].is_svideo;
+ int link_flags = i ? 0 : MEDIA_LNK_FL_ENABLED;
pad->flags = MEDIA_PAD_FL_SOURCE;
ret = media_entity_pads_init(con, 1, pad);
if (ret < 0)
return ret;
ret = media_device_register_entity(sd->v4l2_dev->mdev, con);
if (ret < 0)
return ret;
- ret = media_create_pad_link(con, 0, &sd->entity, port, 0);
+ ret = media_create_pad_link(con, 0, &sd->entity, port, link_flags);
if (ret < 0) {
media_device_unregister_entity(con);
return ret;
}
if (is_svideo) {
/* svideo links to both aip1a and aip1b */
ret = media_create_pad_link(con, 0, &sd->entity,
- port + 1, 0);
+ port + 1, link_flags);
if (ret < 0) {
media_device_unregister_entity(con);
return ret;
}
}
}
Thanks,
Mauro
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
