Hi Mauro, On 18-08-08 15:52, Mauro Carvalho Chehab wrote: > Em Wed, 8 Aug 2018 17:29:49 +0200 > Marco Felsch <m.felsch@xxxxxxxxxxxxxx> escreveu: > > > Hi Mauro, > > > > the discussion about the correct binding was spread around some patches. > > So I will try use the correct thread for that theme. I did my rework for > > the of_graph support on your suggestions [1] and [2]. I attached my work > > as RFC patch. Can you review it, so I can prepare a v2? > > > > [1] https://www.spinics.net/lists/linux-media/msg138545.html > > [2] https://www.spinics.net/lists/linux-media/msg138546.html > > Thanks for the patch. > > Added my comments below. Thanks for your quick response. I integrated the most of your comments and added some more comments below. > > > > > On 18-07-30 15:29, Mauro Carvalho Chehab wrote: > > > Em Thu, 28 Jun 2018 18:20:51 +0200 > > > Marco Felsch <m.felsch@xxxxxxxxxxxxxx> escreveu: > > > > > > > The currrent driver layout had the following layout: > > > > +----------------+ > > > > +-------+ | TVP5150 | > > > > | Comp0 +--+ | | > > > > +-------+ | | +-----+ > > > > +-------+ | +------+ | Src | > > > > | Comp1 +--+--|Sink | +-----+ > > > > +-------+ | +------+ +-----+ > > > > +--------+ | | | Src | > > > > | SVideo +--+ | +-----+ > > > > +--------+ +----------------+ > > > > > > > > Since the device tree abstracts the real hardware this layout is not > > > > correct, because the TVP5150 has 3 physical ports (2 input, 1 output). > > > > Furthermore this layout assumes that there is an additional external mux > > > > in front of the TVP5150. This is not correct because the TVP5150 does > > > > the muxing work. The corresponding of_graph layout will look like: > > > > tvp5150 { > > > > .... > > > > port { > > > > reg = <0>; > > > > endpoint@0 {...}; > > > > endpoint@1 {...}; > > > > endpoint@2 {...}; > > > > }; > > > > > > > > }; > > > > > > > > This patch change the layout to: > > > > +----------------+ > > > > | TVP5150 | > > > > +-------+ +------+ | > > > > | Comp0 +---+ Sink | | > > > > +-------+ +------+ | > > > > +-------+ +------+ +-----+ > > > > | Comp1 +---+ Sink | | Src | > > > > +-------+ +------+ +-----+ > > > > +--------+ +------+ | > > > > | SVideo +---+ Sink | | > > > > +--------+ +------+ | > > > > +----------------+ > > > > > > > > To keep things easy an additional 'virtual' S-Video port is added. More > > > > information about the port mapping can be found in the device tree > > > > binding documentation. The connector entities Comp0/1, SVideo are created > > > > only if they are connected to the correct port. If more than one connector > > > > is available the media_entity_operations.link_setup() callback ensures that > > > > only one connector is active. To change the input src the link between > > > > the TVP5150 pad and the connector must be disabled, then a new link can > > > > be enabled. > > > > > > > > The patch tries to reduce the '#ifdef CONFIG_MEDIA_CONTROLLER' usage to > > > > a minimum. > > > > > > > > Signed-off-by: Marco Felsch <m.felsch@xxxxxxxxxxxxxx> > > > > --- > > > > drivers/media/i2c/tvp5150.c | 322 ++++++++++++++++++++++++++++++++---- > > > > 1 file changed, 287 insertions(+), 35 deletions(-) > > > > > > > > diff --git a/drivers/media/i2c/tvp5150.c b/drivers/media/i2c/tvp5150.c > > > > index a6fec569a610..6ac29c62d99b 100644 > > > > --- a/drivers/media/i2c/tvp5150.c > > > > +++ b/drivers/media/i2c/tvp5150.c > > > > @@ -44,10 +44,30 @@ MODULE_PARM_DESC(debug, "Debug level (0-2)"); > > > > > > > > #define dprintk0(__dev, __arg...) dev_dbg_lvl(__dev, 0, 0, __arg) > > > > > > > > +enum tvp5150_ports { > > > > + TVP5150_PORT_AIP1A = TVP5150_COMPOSITE0, > > > > + TVP5150_PORT_AIP1B, > > > > + /* s-video port is a virtual port */ > > > > + TVP5150_PORT_SVIDEO, > > > > + TVP5150_PORT_YOUT, > > > > + TVP5150_PORT_NUM, > > > > +}; > > > > + > > > > +#ifdef CONFIG_MEDIA_CONTROLLER > > > > +struct tvp5150_connector { > > > > + struct media_entity con; > > > > + struct media_pad pad; > > > > + unsigned int port_num; > > > > +}; > > > > +#endif > > > > + > > > > struct tvp5150 { > > > > struct v4l2_subdev sd; > > > > + struct device_node *endpoints[TVP5150_PORT_NUM]; > > > > #ifdef CONFIG_MEDIA_CONTROLLER > > > > - struct media_pad pads[DEMOD_NUM_PADS]; > > > > + struct media_pad pads[TVP5150_PORT_NUM]; > > > > > > This will cause problems with the current code. > > > > > > When we designed the MC version 2 code, the idea were to allow > > > set properties to entities and to the inputs, but the code > > > was never submitted upstream. > > > > > > A decoder may have several different types of inputs and outputs. > > > Several designs allow using different types of decoders, being > > > saa711x and tvp5150 the most popular ones. Well, depending on > > > the device, the number of PADs and the signals they carry can > > > be different. > > > > > > Without a way to "taint" a pad to the signal it contains, > > > while waiting for the properties API, we added a code that > > > "fixed" the PADs to a certain number. This way, Kernelspace could > > > use the pad "number" as a way to identify the type of signal a > > > PAD carries. > > > > > > The PC consumer drivers use those numbers in order to build the > > > MC graph[1]. > > > > > > A change on this would require adding a property to the pad, in > > > order to indicate the type of signal it provides (RF, luminance IF, > > > chroma IF, audio IF, I2S audio, ...), and to change > > > v4l2_mc_create_media_graph() accordingly. > > > > > > > > > [1] See drivers/media/v4l2-core/v4l2-mc.c at v4l2_mc_create_media_graph() func. > > > > > > > > > > [ snip ] > > > > From d3eb8a7de65fe2f8dd10ced85e4baca8e7898434 Mon Sep 17 00:00:00 2001 > > From: Marco Felsch <m.felsch@xxxxxxxxxxxxxx> > > Date: Thu, 28 Jun 2018 18:20:51 +0200 > > Subject: [RFC] [media] tvp5150: add input source selection of_graph > > support > > > > This patch adds the of_graph support to describe the tvp connections. > > Physical the TVP5150 has three ports: AIP1A, AIP1B and YOUT. As result > > of discussion [1],[2] the device-tree maps these ports 1:1 with one > > deviation. The svideo connector must be conneted to port@0/endpoint@1, > > look at the Documentation for more information. Since the TVP5150 is a > > converter the device-tree must contain at least 1-input and 1-output port. > > The mc-connectors and mc-links are only created if the device-tree > > contains the corresponding connector nodes. If more than one connector is > > available the media_entity_operations.link_setup() callback ensures that > > only one connector is active. To change the input src the active link must > > disabled first, then a new link can be established. > > > > [1] https://www.spinics.net/lists/linux-media/msg138545.html > > [2] https://www.spinics.net/lists/linux-media/msg138546.html > > > > Signed-off-by: Marco Felsch <m.felsch@xxxxxxxxxxxxxx> > > > > --- > > Changelog: > > > > v2: > > - adapt commit message > > - mc: use 2-input and 1-output pad > > - mc: enable svideo on tvp only if both tvp-input pads have a active > > link to the svideo src pad > > - mc: disable svideo on tvp only if both tvp-input pads are inactive > > - dt-support: drop svideo dt port > > - dt-support: move svideo connector to port@0/endpoint@1 > > - dt-support: require at least 1-in and 1-out endpoint > > --- > > drivers/media/i2c/tvp5150.c | 413 ++++++++++++++++++++++++++++++++---- > > 1 file changed, 377 insertions(+), 36 deletions(-) > > > > diff --git a/drivers/media/i2c/tvp5150.c b/drivers/media/i2c/tvp5150.c > > index b5d44c25d1da..be755c5e63a9 100644 > > --- a/drivers/media/i2c/tvp5150.c > > +++ b/drivers/media/i2c/tvp5150.c > > @@ -43,16 +43,38 @@ MODULE_PARM_DESC(debug, "Debug level (0-2)"); > > > > #define dprintk0(__dev, __arg...) dev_dbg_lvl(__dev, 0, 0, __arg) > > > > +#ifdef CONFIG_MEDIA_CONTROLLER > > enum tvp5150_pads { > > - TVP5150_PAD_IF_INPUT, > > - TVP5150_PAD_VID_OUT, > > - TVP5150_NUM_PADS > > + TVP5150_PAD_AIP1A = TVP5150_COMPOSITE0, > > + TVP5150_PAD_AIP1B, > > + TVP5150_PAD_VID_OUT, > > + TVP5150_NUM_PADS > > +}; > > + > > +enum tvp5150_pads_state { > > + TVP5150_PAD_INACTIVE, > > + TVP5150_PAD_ACTIVE_COMPOSITE, > > + TVP5150_PAD_ACTIVE_SVIDEO, > > +}; > > + > > +struct tvp5150_connector { > > + struct media_entity ent; > > + struct media_pad pad; > > + unsigned int port_num; > > + bool is_svideo; > > }; > > +#endif > > > > struct tvp5150 { > > struct v4l2_subdev sd; > > + /* additional additional endpoint for the svideo connector */ > > + struct device_node *endpoints[TVP5150_NUM_PADS + 1]; > > + unsigned int endpoints_num; > > #ifdef CONFIG_MEDIA_CONTROLLER > > struct media_pad pads[TVP5150_NUM_PADS]; > > + int pads_state[TVP5150_NUM_PADS]; > > + struct tvp5150_connector *connectors; > > + int connectors_num; > > #endif > > struct v4l2_ctrl_handler hdl; > > struct v4l2_rect rect; > > @@ -1168,6 +1190,135 @@ static int tvp5150_enum_frame_size(struct v4l2_subdev *sd, > > return 0; > > } > > > > +/**************************************************************************** > > + * Media entity ops > > + ****************************************************************************/ > > +#ifdef CONFIG_MEDIA_CONTROLLER > > +static int tvp5150_s_routing(struct v4l2_subdev *sd, u32 input, u32 output, > > + u32 config); > > +static int tvp5150_link_setup(struct media_entity *entity, > > + const struct media_pad *local, > > + const struct media_pad *remote, u32 flags) > > +{ > > + struct v4l2_subdev *sd = media_entity_to_v4l2_subdev(entity); > > + struct tvp5150 *decoder = to_tvp5150(sd); > > + int *pad_state = &decoder->pads_state[0]; > > + int i, ret = 0, active_pad = -1; > > + bool is_svideo = false; > > + > > + /* > > + * The tvp state is determined by the enabled sink pad link. > > + * Enabling or disabling the source pad link has no effect. > > + */ > > + if (local->flags & MEDIA_PAD_FL_SOURCE) > > + return 0; > > + > > + /* check if the svideo connector should be enabled */ > > + for (i = 0; i < decoder->connectors_num; i++) { > > + if (remote->entity == &decoder->connectors[i].ent) { > > + is_svideo = decoder->connectors[i].is_svideo; > > + break; > > + } > > + } > > + > > + /* check if there is enabled link */ > > + for (i = 0; i < TVP5150_NUM_PADS - 1; i++) { > > + if ((pad_state[i] == TVP5150_PAD_ACTIVE_COMPOSITE) || > > + (pad_state[i] == TVP5150_PAD_ACTIVE_SVIDEO)) { > > + active_pad = i; > > + break; > > + } > > + } > > + > > + dev_dbg(sd->dev, "link setup '%s':%d->'%s':%d[%d]", > > + remote->entity->name, remote->index, local->entity->name, > > + local->index, flags & MEDIA_LNK_FL_ENABLED); > > Hmm... the remote is the connector, right? I would switch the > print message to point from the connector to tvp5150, as this is > the signal flow. I don't know what you mean, I tought that's what I'm already do. If I change it it will print something like: tvp5150 2-005d :0 -> Comp0 :0[1] > > Btw, it would likely be better to call it "connector" or "conn_entity", > to make it clearer. I tought remote is the common nomenclature. Also the remote mustn't be a connector. In my case it's a soldered camera. With this in mind, you think it should be still changed? > > > + > > + if (flags & MEDIA_LNK_FL_ENABLED) { > > + /* > > + * Composite activation: all links must be inactive. > > + * Svideo activation: one link can be active if it is a svideo > > + * link. Return error in case of a active composite link or both > > + * svideo links are active. > > + */ > > + if (active_pad >= 0 && !is_svideo) { > > + ret = -EBUSY; > > + goto out; > > + } else if (active_pad >= 0 && is_svideo && > > + pad_state[active_pad] == > > + TVP5150_PAD_ACTIVE_COMPOSITE) { > > + ret = -EBUSY; > > + goto out; > > + } else if (active_pad >= 0) { > > + /* check if 2nd svideo link is active too */ > > + for (i = 0; i < TVP5150_NUM_PADS - 1; i++) { > > + if (pad_state[i] == TVP5150_PAD_ACTIVE_SVIDEO) { > > + if (i != active_pad) { > > + ret = -EBUSY; > > + goto out; > > + } > > + } > > + } > > + } > > That may require some additional discussions. > > I guess this is not the way it should be. I mean, it should be possible > to change the routing while streaming, without disabling the video > output. That's the behavior that TV generic applications like tvtime, > xawtv, etc rely on. > > So, probably, the right thing to do here is to disable the active_pad > and enable the newer one, if there is an active pad. > > This way, it would work both if the userspace first disables the link > and then enables a new one, or if it switches without explicitly > disabling the previous one. Okay I change this behaviour. > > > + > > + dev_dbg(sd->dev, "Setting %d active [%s]\n", local->index, > > + is_svideo ? "svideo": "composite"); > > + pad_state[local->index] = is_svideo ? > > + TVP5150_PAD_ACTIVE_SVIDEO : TVP5150_PAD_ACTIVE_COMPOSITE; > > + > > + if (is_svideo) { > > + unsigned int active_link_cnt = 0; > > + > > + /* enable svideo only if we have two active links */ > > + for (i = 0; i > TVP5150_NUM_PADS - 1; i++) > > + if (pad_state[i] == TVP5150_PAD_ACTIVE_SVIDEO) > > + active_link_cnt++; > > + if (active_link_cnt == 2) > > + tvp5150_s_routing(sd, TVP5150_SVIDEO, > > + TVP5150_NORMAL, 0); > > + } else { > > + tvp5150_s_routing(sd, local->index, TVP5150_NORMAL, 0); > > + } > > + } else { > > + /* > > + * Svideo streams on two pads and user can disable AIP1A or > > + * AIP1B first. So check only if user wants to disable a not > > + * enabled composite pad. > > + */ > > + if (!is_svideo && active_pad != local->index) > > + goto out; > > + > > + dev_dbg(sd->dev, "going inactive\n"); > > + pad_state[local->index] = TVP5150_PAD_INACTIVE; > > + > > + /* > > + * Output black screen for deselected input if TVP5150 variant > > + * supports this. > > + */ > > + if (is_svideo) { > > + unsigned int inactive_link_cnt = 0; > > + > > + /* disable svideo only if we have two inactive links */ > > + for (i = 0; i > TVP5150_NUM_PADS - 1; i++) > > + if (pad_state[i] == TVP5150_PAD_INACTIVE) > > + inactive_link_cnt++; > > + if (inactive_link_cnt == 2) > > + tvp5150_s_routing(sd, TVP5150_SVIDEO, > > + TVP5150_BLACK_SCREEN, 0); > > + > > + } else { > > + tvp5150_s_routing(sd, local->index, > > + TVP5150_BLACK_SCREEN, 0); > > + } > > + } > > +out: > > + return ret; > > +} > > + > > +static const struct media_entity_operations tvp5150_sd_media_ops = { > > + .link_setup = tvp5150_link_setup, > > +}; > > +#endif > > /**************************************************************************** > > I2C Command > > ****************************************************************************/ > > @@ -1315,6 +1466,50 @@ static int tvp5150_g_tuner(struct v4l2_subdev *sd, struct v4l2_tuner *vt) > > return 0; > > } > > > > +static int tvp5150_registered(struct v4l2_subdev *sd) > > +{ > > +#ifdef CONFIG_MEDIA_CONTROLLER > > + struct tvp5150 *decoder = to_tvp5150(sd); > > + unsigned int i; > > + int ret; > > + > > + for (i = 0; i < decoder->connectors_num; i++) { > > + struct media_entity *con = &decoder->connectors[i].ent; > > + struct media_pad *pad = &decoder->connectors[i].pad; > > + unsigned int port = decoder->connectors[i].port_num; > > + bool is_svideo = decoder->connectors[i].is_svideo; > > + > > + pad->flags = MEDIA_PAD_FL_SOURCE; > > + ret = media_entity_pads_init(con, 1, pad); > > + if (ret < 0) > > + return ret; > > + > > + ret = media_device_register_entity(sd->v4l2_dev->mdev, con); > > + if (ret < 0) > > + return ret; > > + > > + ret = media_create_pad_link(con, 0, &sd->entity, port, 0); > > + if (ret < 0) { > > + media_device_unregister_entity(con); > > + return ret; > > + } > > + > > + if (is_svideo) { > > + /* svideo links to both aip1a and aip1b */ > > + ret = media_create_pad_link(con, 0, &sd->entity, > > + port + 1, 0); > > + if (ret < 0) { > > + media_device_unregister_entity(con); > > + return ret; > > + } > > + } > > + > > + } > > IMO, it should route to the first available connector. Did you mean to set the link status to enabled? If so I have one question else can you tell me what you mean? Should I use the media_entity_setup_link() helper or should I mark it as enabled during media_create_pad_link()? Now I did something like: if (i == 0) { list_for_each_entry(link, &con->links, list) { media_entity_setup_link(link, MEDIA_LNK_FL_ENABLED); } } > > > +#endif > > + return 0; > > +} > > + > > + > > /* ----------------------------------------------------------------------- */ > > > > static const struct v4l2_ctrl_ops tvp5150_ctrl_ops = { > > @@ -1368,6 +1563,10 @@ static const struct v4l2_subdev_ops tvp5150_ops = { > > .pad = &tvp5150_pad_ops, > > }; > > > > +static const struct v4l2_subdev_internal_ops tvp5150_internal_ops = { > > + .registered = tvp5150_registered, > > +}; > > + > > /**************************************************************************** > > I2C Client & Driver > > ****************************************************************************/ > > @@ -1516,38 +1715,186 @@ static int tvp5150_init(struct i2c_client *c) > > return 0; > > } > > > > -static int tvp5150_parse_dt(struct tvp5150 *decoder, struct device_node *np) > > +static int tvp5150_mc_init(struct v4l2_subdev *sd) > > { > > - struct v4l2_fwnode_endpoint bus_cfg; > > - struct device_node *ep; > > - unsigned int flags; > > - int ret = 0; > > +#if defined(CONFIG_MEDIA_CONTROLLER) > > + struct tvp5150 *decoder = to_tvp5150(sd); > > + struct device *dev = decoder->sd.dev; > > + unsigned int i; > > + int ret; > > > > - ep = of_graph_get_next_endpoint(np, NULL); > > - if (!ep) > > - return -EINVAL; > > + sd->entity.ops = &tvp5150_sd_media_ops; > > + sd->entity.function = MEDIA_ENT_F_ATV_DECODER; > > > > - ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep), &bus_cfg); > > - if (ret) > > - goto err; > > + /* Initialize all TVP5150 pads */ > > + for (i = 0; i < TVP5150_NUM_PADS; i++) { > > + if (i < TVP5150_NUM_PADS - 1) { > > + decoder->pads[i].flags = MEDIA_PAD_FL_SINK; > > + decoder->pads[i].sig_type = PAD_SIGNAL_ANALOG; > > + } else { > > + decoder->pads[i].flags = MEDIA_PAD_FL_SOURCE; > > + decoder->pads[i].sig_type = PAD_SIGNAL_DV; > > + } > > + } > > + ret = media_entity_pads_init(&sd->entity, TVP5150_NUM_PADS, > > + decoder->pads); > > + if (ret < 0) > > + return ret; > > + > > + /* in case of no oftree support */ > > + if (!decoder->endpoints[0]) > > + return 0; > > Hmm... > > > + > > + /* Allocate and initialize all available input connectors */ > > + decoder->connectors = devm_kcalloc(dev, decoder->connectors_num, > > + sizeof(*decoder->connectors), > > + GFP_KERNEL); > > + if (!decoder->connectors) > > + return -ENOMEM; > > + > > + for (i = 0; i < decoder->connectors_num; i++) { > > + struct device_node *rp; > > + struct of_endpoint ep; > > + > > + rp = of_graph_get_remote_port_parent(decoder->endpoints[i]); > > + of_graph_parse_endpoint(decoder->endpoints[i], &ep); > > + decoder->connectors[i].port_num = ep.port; > > + decoder->connectors[i].is_svideo = !!of_device_is_compatible(rp, > > + "svideo-connector"); > > + > > + if (decoder->connectors[i].is_svideo) > > + decoder->connectors[i].ent.function = > > + MEDIA_ENT_F_CONN_SVIDEO; > > + else > > + decoder->connectors[i].ent.function = > > + MEDIA_ENT_F_CONN_COMPOSITE; > > + > > + decoder->connectors[i].ent.flags = MEDIA_ENT_FL_CONNECTOR; > > + ret = of_property_read_string(rp, "label", > > + &decoder->connectors[i].ent.name); > > + if (ret < 0) > > + return ret; > > I would prefer, instead, to have a separate routine for OF. I'll probably > use something like the above for the non-DT devices (e. g. the ones using > em28xx driver). Okay, I refactored it. > > > + } > > +#endif > > + return 0; > > +} > > + > > +static bool tvp5150_valid_input(struct device_node *endpoint, > > + unsigned int port, unsigned int id) > > Please call it as tvp5150_of_valid_input(). We may need something similar > for devices based on em28xx (passing info via platform_data). Okay, I changed it. > > > +{ > > + struct device_node *rp = of_graph_get_remote_port_parent(endpoint); > > + const char *input; > > + int ret; > > + > > + /* perform some basic checks needed for later mc_init */ > > + switch (port) { > > + case TVP5150_PAD_AIP1A: > > + /* svideo must be connected to endpoint@1 */ > > + ret = id ? of_device_is_compatible(rp, "svideo-connector") : > > + of_device_is_compatible(rp, "composite-video-connector"); > > + if (!ret) > > + return false; > > + break; > > + case TVP5150_PAD_AIP1B: > > + ret = of_device_is_compatible(rp, "composite-video-connector"); > > + if (!ret) > > + return false; > > + break; > > + } > > + > > + ret = of_property_read_string(rp, "label", &input); > > + if (ret < 0) > > + return false; > > + > > + return true; > > +} > > > > - flags = bus_cfg.bus.parallel.flags; > > +static int tvp5150_parse_dt(struct tvp5150 *decoder, struct device_node *np) > > +{ > > + struct device *dev = decoder->sd.dev; > > + struct v4l2_fwnode_endpoint bus_cfg; > > + struct device_node *ep_np; > > + unsigned int flags; > > + int ret, i = 0, in = 0; > > + bool found = false; > > > > - if (bus_cfg.bus_type == V4L2_MBUS_PARALLEL && > > - !(flags & V4L2_MBUS_HSYNC_ACTIVE_HIGH && > > - flags & V4L2_MBUS_VSYNC_ACTIVE_HIGH && > > - flags & V4L2_MBUS_FIELD_EVEN_LOW)) { > > + /* at least 1 output and 1 input */ > > + decoder->endpoints_num = of_graph_get_endpoint_count(np); > > + if (decoder->endpoints_num < 2 || decoder->endpoints_num > 4) { > > ret = -EINVAL; > > goto err; > > } > > > > - decoder->mbus_type = bus_cfg.bus_type; > > + for_each_endpoint_of_node(np, ep_np) { > > + struct of_endpoint ep; > > > > + of_graph_parse_endpoint(ep_np, &ep); > > + if (decoder->endpoints[i]) { > > + /* this should never happen */ > > + dev_err(dev, "Invalid endpoint %pOF on port %d\n", > > + ep.local_node, ep.port); > > + ret = -EINVAL; > > + goto err; > > + } > > + > > + switch (ep.port) { > > + case TVP5150_PAD_AIP1A: > > + case TVP5150_PAD_AIP1B: > > + if (!tvp5150_valid_input(ep_np, ep.port, ep.id)) { > > + dev_err(dev, > > + "Invalid endpoint %pOF on port %d\n", > > + ep.local_node, ep.port); > > + ret = -EINVAL; > > + goto err; > > + } > > + in++; > > + break; > > + case TVP5150_PAD_VID_OUT: > > + ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep_np), > > + &bus_cfg); > > + if (ret) > > + goto err; > > + > > + flags = bus_cfg.bus.parallel.flags; > > + > > + if (bus_cfg.bus_type == V4L2_MBUS_PARALLEL && > > + !(flags & V4L2_MBUS_HSYNC_ACTIVE_HIGH && > > + flags & V4L2_MBUS_VSYNC_ACTIVE_HIGH && > > + flags & V4L2_MBUS_FIELD_EVEN_LOW)) { > > + ret = -EINVAL; > > + goto err; > > + } > > + > > + decoder->mbus_type = bus_cfg.bus_type; > > + break; > > + default: > > + dev_err(dev, "Invalid port %d for endpoint %pOF\n", > > + ep.port, ep.local_node); > > + ret = -EINVAL; > > + goto err; > > + } > > + > > + of_node_get(ep_np); > > + decoder->endpoints[i] = ep_np; > > + i++; > > + > > + found = true; > > + } > > + > > + decoder->connectors_num = in; > > + return found ? 0 : -ENODEV; > > err: > > - of_node_put(ep); > > return ret; > > } > > > > +static void tvp5150_dt_cleanup(struct tvp5150 *decoder) > > +{ > > + unsigned int i; > > + > > + for (i = 0; i < TVP5150_NUM_PADS; i++) > > + of_node_put(decoder->endpoints[i]); > > +} > > + > > static const char * const tvp5150_test_patterns[2] = { > > "Disabled", > > "Black screen" > > @@ -1586,7 +1933,7 @@ static int tvp5150_probe(struct i2c_client *c, > > res = tvp5150_parse_dt(core, np); > > if (res) { > > dev_err(sd->dev, "DT parsing error: %d\n", res); > > - return res; > > + goto err_cleanup_dt; > > } > > } else { > > /* Default to BT.656 embedded sync */ > > @@ -1594,25 +1941,16 @@ static int tvp5150_probe(struct i2c_client *c, > > } > > > > v4l2_i2c_subdev_init(sd, c, &tvp5150_ops); > > + sd->internal_ops = &tvp5150_internal_ops; > > sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; > > > > -#if defined(CONFIG_MEDIA_CONTROLLER) > > - core->pads[TVP5150_PAD_IF_INPUT].flags = MEDIA_PAD_FL_SINK; > > - core->pads[TVP5150_PAD_IF_INPUT].sig_type = PAD_SIGNAL_ANALOG; > > - core->pads[TVP5150_PAD_VID_OUT].flags = MEDIA_PAD_FL_SOURCE; > > - core->pads[TVP5150_PAD_VID_OUT].sig_type = PAD_SIGNAL_DV; > > - > > - sd->entity.function = MEDIA_ENT_F_ATV_DECODER; > > - > > - res = media_entity_pads_init(&sd->entity, TVP5150_NUM_PADS, core->pads); > > - if (res < 0) > > - return res; > > - > > -#endif > > + res = tvp5150_mc_init(sd); > > + if (res) > > + goto err_cleanup_dt; > > > > res = tvp5150_detect_version(core); > > if (res < 0) > > - return res; > > + goto err_cleanup_dt; > > > > core->norm = V4L2_STD_ALL; /* Default is autodetect */ > > core->detected_norm = V4L2_STD_UNKNOWN; > > @@ -1664,6 +2002,9 @@ static int tvp5150_probe(struct i2c_client *c, > > err: > > v4l2_ctrl_handler_free(&core->hdl); > > return res; > > +err_cleanup_dt: > > + tvp5150_dt_cleanup(core); > > + return res; > > } > > > > static int tvp5150_remove(struct i2c_client *c) > > > > Thanks, > Mauro Regards, Marco -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
