Em Wed, 8 Aug 2018 17:29:49 +0200 Marco Felsch <m.felsch@xxxxxxxxxxxxxx> escreveu: > Hi Mauro, > > the discussion about the correct binding was spread around some patches. > So I will try use the correct thread for that theme. I did my rework for > the of_graph support on your suggestions [1] and [2]. I attached my work > as RFC patch. Can you review it, so I can prepare a v2? > > [1] https://www.spinics.net/lists/linux-media/msg138545.html > [2] https://www.spinics.net/lists/linux-media/msg138546.html Thanks for the patch. Added my comments below. > > On 18-07-30 15:29, Mauro Carvalho Chehab wrote: > > Em Thu, 28 Jun 2018 18:20:51 +0200 > > Marco Felsch <m.felsch@xxxxxxxxxxxxxx> escreveu: > > > > > The currrent driver layout had the following layout: > > > +----------------+ > > > +-------+ | TVP5150 | > > > | Comp0 +--+ | | > > > +-------+ | | +-----+ > > > +-------+ | +------+ | Src | > > > | Comp1 +--+--|Sink | +-----+ > > > +-------+ | +------+ +-----+ > > > +--------+ | | | Src | > > > | SVideo +--+ | +-----+ > > > +--------+ +----------------+ > > > > > > Since the device tree abstracts the real hardware this layout is not > > > correct, because the TVP5150 has 3 physical ports (2 input, 1 output). > > > Furthermore this layout assumes that there is an additional external mux > > > in front of the TVP5150. This is not correct because the TVP5150 does > > > the muxing work. The corresponding of_graph layout will look like: > > > tvp5150 { > > > .... > > > port { > > > reg = <0>; > > > endpoint@0 {...}; > > > endpoint@1 {...}; > > > endpoint@2 {...}; > > > }; > > > > > > }; > > > > > > This patch change the layout to: > > > +----------------+ > > > | TVP5150 | > > > +-------+ +------+ | > > > | Comp0 +---+ Sink | | > > > +-------+ +------+ | > > > +-------+ +------+ +-----+ > > > | Comp1 +---+ Sink | | Src | > > > +-------+ +------+ +-----+ > > > +--------+ +------+ | > > > | SVideo +---+ Sink | | > > > +--------+ +------+ | > > > +----------------+ > > > > > > To keep things easy an additional 'virtual' S-Video port is added. More > > > information about the port mapping can be found in the device tree > > > binding documentation. The connector entities Comp0/1, SVideo are created > > > only if they are connected to the correct port. If more than one connector > > > is available the media_entity_operations.link_setup() callback ensures that > > > only one connector is active. To change the input src the link between > > > the TVP5150 pad and the connector must be disabled, then a new link can > > > be enabled. > > > > > > The patch tries to reduce the '#ifdef CONFIG_MEDIA_CONTROLLER' usage to > > > a minimum. > > > > > > Signed-off-by: Marco Felsch <m.felsch@xxxxxxxxxxxxxx> > > > --- > > > drivers/media/i2c/tvp5150.c | 322 ++++++++++++++++++++++++++++++++---- > > > 1 file changed, 287 insertions(+), 35 deletions(-) > > > > > > diff --git a/drivers/media/i2c/tvp5150.c b/drivers/media/i2c/tvp5150.c > > > index a6fec569a610..6ac29c62d99b 100644 > > > --- a/drivers/media/i2c/tvp5150.c > > > +++ b/drivers/media/i2c/tvp5150.c > > > @@ -44,10 +44,30 @@ MODULE_PARM_DESC(debug, "Debug level (0-2)"); > > > > > > #define dprintk0(__dev, __arg...) dev_dbg_lvl(__dev, 0, 0, __arg) > > > > > > +enum tvp5150_ports { > > > + TVP5150_PORT_AIP1A = TVP5150_COMPOSITE0, > > > + TVP5150_PORT_AIP1B, > > > + /* s-video port is a virtual port */ > > > + TVP5150_PORT_SVIDEO, > > > + TVP5150_PORT_YOUT, > > > + TVP5150_PORT_NUM, > > > +}; > > > + > > > +#ifdef CONFIG_MEDIA_CONTROLLER > > > +struct tvp5150_connector { > > > + struct media_entity con; > > > + struct media_pad pad; > > > + unsigned int port_num; > > > +}; > > > +#endif > > > + > > > struct tvp5150 { > > > struct v4l2_subdev sd; > > > + struct device_node *endpoints[TVP5150_PORT_NUM]; > > > #ifdef CONFIG_MEDIA_CONTROLLER > > > - struct media_pad pads[DEMOD_NUM_PADS]; > > > + struct media_pad pads[TVP5150_PORT_NUM]; > > > > This will cause problems with the current code. > > > > When we designed the MC version 2 code, the idea were to allow > > set properties to entities and to the inputs, but the code > > was never submitted upstream. > > > > A decoder may have several different types of inputs and outputs. > > Several designs allow using different types of decoders, being > > saa711x and tvp5150 the most popular ones. Well, depending on > > the device, the number of PADs and the signals they carry can > > be different. > > > > Without a way to "taint" a pad to the signal it contains, > > while waiting for the properties API, we added a code that > > "fixed" the PADs to a certain number. This way, Kernelspace could > > use the pad "number" as a way to identify the type of signal a > > PAD carries. > > > > The PC consumer drivers use those numbers in order to build the > > MC graph[1]. > > > > A change on this would require adding a property to the pad, in > > order to indicate the type of signal it provides (RF, luminance IF, > > chroma IF, audio IF, I2S audio, ...), and to change > > v4l2_mc_create_media_graph() accordingly. > > > > > > [1] See drivers/media/v4l2-core/v4l2-mc.c at v4l2_mc_create_media_graph() func. > > > > > > [ snip ] > > From d3eb8a7de65fe2f8dd10ced85e4baca8e7898434 Mon Sep 17 00:00:00 2001 > From: Marco Felsch <m.felsch@xxxxxxxxxxxxxx> > Date: Thu, 28 Jun 2018 18:20:51 +0200 > Subject: [RFC] [media] tvp5150: add input source selection of_graph > support > > This patch adds the of_graph support to describe the tvp connections. > Physical the TVP5150 has three ports: AIP1A, AIP1B and YOUT. As result > of discussion [1],[2] the device-tree maps these ports 1:1 with one > deviation. The svideo connector must be conneted to port@0/endpoint@1, > look at the Documentation for more information. Since the TVP5150 is a > converter the device-tree must contain at least 1-input and 1-output port. > The mc-connectors and mc-links are only created if the device-tree > contains the corresponding connector nodes. If more than one connector is > available the media_entity_operations.link_setup() callback ensures that > only one connector is active. To change the input src the active link must > disabled first, then a new link can be established. > > [1] https://www.spinics.net/lists/linux-media/msg138545.html > [2] https://www.spinics.net/lists/linux-media/msg138546.html > > Signed-off-by: Marco Felsch <m.felsch@xxxxxxxxxxxxxx> > > --- > Changelog: > > v2: > - adapt commit message > - mc: use 2-input and 1-output pad > - mc: enable svideo on tvp only if both tvp-input pads have a active > link to the svideo src pad > - mc: disable svideo on tvp only if both tvp-input pads are inactive > - dt-support: drop svideo dt port > - dt-support: move svideo connector to port@0/endpoint@1 > - dt-support: require at least 1-in and 1-out endpoint > --- > drivers/media/i2c/tvp5150.c | 413 ++++++++++++++++++++++++++++++++---- > 1 file changed, 377 insertions(+), 36 deletions(-) > > diff --git a/drivers/media/i2c/tvp5150.c b/drivers/media/i2c/tvp5150.c > index b5d44c25d1da..be755c5e63a9 100644 > --- a/drivers/media/i2c/tvp5150.c > +++ b/drivers/media/i2c/tvp5150.c > @@ -43,16 +43,38 @@ MODULE_PARM_DESC(debug, "Debug level (0-2)"); > > #define dprintk0(__dev, __arg...) dev_dbg_lvl(__dev, 0, 0, __arg) > > +#ifdef CONFIG_MEDIA_CONTROLLER > enum tvp5150_pads { > - TVP5150_PAD_IF_INPUT, > - TVP5150_PAD_VID_OUT, > - TVP5150_NUM_PADS > + TVP5150_PAD_AIP1A = TVP5150_COMPOSITE0, > + TVP5150_PAD_AIP1B, > + TVP5150_PAD_VID_OUT, > + TVP5150_NUM_PADS > +}; > + > +enum tvp5150_pads_state { > + TVP5150_PAD_INACTIVE, > + TVP5150_PAD_ACTIVE_COMPOSITE, > + TVP5150_PAD_ACTIVE_SVIDEO, > +}; > + > +struct tvp5150_connector { > + struct media_entity ent; > + struct media_pad pad; > + unsigned int port_num; > + bool is_svideo; > }; > +#endif > > struct tvp5150 { > struct v4l2_subdev sd; > + /* additional additional endpoint for the svideo connector */ > + struct device_node *endpoints[TVP5150_NUM_PADS + 1]; > + unsigned int endpoints_num; > #ifdef CONFIG_MEDIA_CONTROLLER > struct media_pad pads[TVP5150_NUM_PADS]; > + int pads_state[TVP5150_NUM_PADS]; > + struct tvp5150_connector *connectors; > + int connectors_num; > #endif > struct v4l2_ctrl_handler hdl; > struct v4l2_rect rect; > @@ -1168,6 +1190,135 @@ static int tvp5150_enum_frame_size(struct v4l2_subdev *sd, > return 0; > } > > +/**************************************************************************** > + * Media entity ops > + ****************************************************************************/ > +#ifdef CONFIG_MEDIA_CONTROLLER > +static int tvp5150_s_routing(struct v4l2_subdev *sd, u32 input, u32 output, > + u32 config); > +static int tvp5150_link_setup(struct media_entity *entity, > + const struct media_pad *local, > + const struct media_pad *remote, u32 flags) > +{ > + struct v4l2_subdev *sd = media_entity_to_v4l2_subdev(entity); > + struct tvp5150 *decoder = to_tvp5150(sd); > + int *pad_state = &decoder->pads_state[0]; > + int i, ret = 0, active_pad = -1; > + bool is_svideo = false; > + > + /* > + * The tvp state is determined by the enabled sink pad link. > + * Enabling or disabling the source pad link has no effect. > + */ > + if (local->flags & MEDIA_PAD_FL_SOURCE) > + return 0; > + > + /* check if the svideo connector should be enabled */ > + for (i = 0; i < decoder->connectors_num; i++) { > + if (remote->entity == &decoder->connectors[i].ent) { > + is_svideo = decoder->connectors[i].is_svideo; > + break; > + } > + } > + > + /* check if there is enabled link */ > + for (i = 0; i < TVP5150_NUM_PADS - 1; i++) { > + if ((pad_state[i] == TVP5150_PAD_ACTIVE_COMPOSITE) || > + (pad_state[i] == TVP5150_PAD_ACTIVE_SVIDEO)) { > + active_pad = i; > + break; > + } > + } > + > + dev_dbg(sd->dev, "link setup '%s':%d->'%s':%d[%d]", > + remote->entity->name, remote->index, local->entity->name, > + local->index, flags & MEDIA_LNK_FL_ENABLED); Hmm... the remote is the connector, right? I would switch the print message to point from the connector to tvp5150, as this is the signal flow. Btw, it would likely be better to call it "connector" or "conn_entity", to make it clearer. > + > + if (flags & MEDIA_LNK_FL_ENABLED) { > + /* > + * Composite activation: all links must be inactive. > + * Svideo activation: one link can be active if it is a svideo > + * link. Return error in case of a active composite link or both > + * svideo links are active. > + */ > + if (active_pad >= 0 && !is_svideo) { > + ret = -EBUSY; > + goto out; > + } else if (active_pad >= 0 && is_svideo && > + pad_state[active_pad] == > + TVP5150_PAD_ACTIVE_COMPOSITE) { > + ret = -EBUSY; > + goto out; > + } else if (active_pad >= 0) { > + /* check if 2nd svideo link is active too */ > + for (i = 0; i < TVP5150_NUM_PADS - 1; i++) { > + if (pad_state[i] == TVP5150_PAD_ACTIVE_SVIDEO) { > + if (i != active_pad) { > + ret = -EBUSY; > + goto out; > + } > + } > + } > + } That may require some additional discussions. I guess this is not the way it should be. I mean, it should be possible to change the routing while streaming, without disabling the video output. That's the behavior that TV generic applications like tvtime, xawtv, etc rely on. So, probably, the right thing to do here is to disable the active_pad and enable the newer one, if there is an active pad. This way, it would work both if the userspace first disables the link and then enables a new one, or if it switches without explicitly disabling the previous one. > + > + dev_dbg(sd->dev, "Setting %d active [%s]\n", local->index, > + is_svideo ? "svideo": "composite"); > + pad_state[local->index] = is_svideo ? > + TVP5150_PAD_ACTIVE_SVIDEO : TVP5150_PAD_ACTIVE_COMPOSITE; > + > + if (is_svideo) { > + unsigned int active_link_cnt = 0; > + > + /* enable svideo only if we have two active links */ > + for (i = 0; i > TVP5150_NUM_PADS - 1; i++) > + if (pad_state[i] == TVP5150_PAD_ACTIVE_SVIDEO) > + active_link_cnt++; > + if (active_link_cnt == 2) > + tvp5150_s_routing(sd, TVP5150_SVIDEO, > + TVP5150_NORMAL, 0); > + } else { > + tvp5150_s_routing(sd, local->index, TVP5150_NORMAL, 0); > + } > + } else { > + /* > + * Svideo streams on two pads and user can disable AIP1A or > + * AIP1B first. So check only if user wants to disable a not > + * enabled composite pad. > + */ > + if (!is_svideo && active_pad != local->index) > + goto out; > + > + dev_dbg(sd->dev, "going inactive\n"); > + pad_state[local->index] = TVP5150_PAD_INACTIVE; > + > + /* > + * Output black screen for deselected input if TVP5150 variant > + * supports this. > + */ > + if (is_svideo) { > + unsigned int inactive_link_cnt = 0; > + > + /* disable svideo only if we have two inactive links */ > + for (i = 0; i > TVP5150_NUM_PADS - 1; i++) > + if (pad_state[i] == TVP5150_PAD_INACTIVE) > + inactive_link_cnt++; > + if (inactive_link_cnt == 2) > + tvp5150_s_routing(sd, TVP5150_SVIDEO, > + TVP5150_BLACK_SCREEN, 0); > + > + } else { > + tvp5150_s_routing(sd, local->index, > + TVP5150_BLACK_SCREEN, 0); > + } > + } > +out: > + return ret; > +} > + > +static const struct media_entity_operations tvp5150_sd_media_ops = { > + .link_setup = tvp5150_link_setup, > +}; > +#endif > /**************************************************************************** > I2C Command > ****************************************************************************/ > @@ -1315,6 +1466,50 @@ static int tvp5150_g_tuner(struct v4l2_subdev *sd, struct v4l2_tuner *vt) > return 0; > } > > +static int tvp5150_registered(struct v4l2_subdev *sd) > +{ > +#ifdef CONFIG_MEDIA_CONTROLLER > + struct tvp5150 *decoder = to_tvp5150(sd); > + unsigned int i; > + int ret; > + > + for (i = 0; i < decoder->connectors_num; i++) { > + struct media_entity *con = &decoder->connectors[i].ent; > + struct media_pad *pad = &decoder->connectors[i].pad; > + unsigned int port = decoder->connectors[i].port_num; > + bool is_svideo = decoder->connectors[i].is_svideo; > + > + pad->flags = MEDIA_PAD_FL_SOURCE; > + ret = media_entity_pads_init(con, 1, pad); > + if (ret < 0) > + return ret; > + > + ret = media_device_register_entity(sd->v4l2_dev->mdev, con); > + if (ret < 0) > + return ret; > + > + ret = media_create_pad_link(con, 0, &sd->entity, port, 0); > + if (ret < 0) { > + media_device_unregister_entity(con); > + return ret; > + } > + > + if (is_svideo) { > + /* svideo links to both aip1a and aip1b */ > + ret = media_create_pad_link(con, 0, &sd->entity, > + port + 1, 0); > + if (ret < 0) { > + media_device_unregister_entity(con); > + return ret; > + } > + } > + > + } IMO, it should route to the first available connector. > +#endif > + return 0; > +} > + > + > /* ----------------------------------------------------------------------- */ > > static const struct v4l2_ctrl_ops tvp5150_ctrl_ops = { > @@ -1368,6 +1563,10 @@ static const struct v4l2_subdev_ops tvp5150_ops = { > .pad = &tvp5150_pad_ops, > }; > > +static const struct v4l2_subdev_internal_ops tvp5150_internal_ops = { > + .registered = tvp5150_registered, > +}; > + > /**************************************************************************** > I2C Client & Driver > ****************************************************************************/ > @@ -1516,38 +1715,186 @@ static int tvp5150_init(struct i2c_client *c) > return 0; > } > > -static int tvp5150_parse_dt(struct tvp5150 *decoder, struct device_node *np) > +static int tvp5150_mc_init(struct v4l2_subdev *sd) > { > - struct v4l2_fwnode_endpoint bus_cfg; > - struct device_node *ep; > - unsigned int flags; > - int ret = 0; > +#if defined(CONFIG_MEDIA_CONTROLLER) > + struct tvp5150 *decoder = to_tvp5150(sd); > + struct device *dev = decoder->sd.dev; > + unsigned int i; > + int ret; > > - ep = of_graph_get_next_endpoint(np, NULL); > - if (!ep) > - return -EINVAL; > + sd->entity.ops = &tvp5150_sd_media_ops; > + sd->entity.function = MEDIA_ENT_F_ATV_DECODER; > > - ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep), &bus_cfg); > - if (ret) > - goto err; > + /* Initialize all TVP5150 pads */ > + for (i = 0; i < TVP5150_NUM_PADS; i++) { > + if (i < TVP5150_NUM_PADS - 1) { > + decoder->pads[i].flags = MEDIA_PAD_FL_SINK; > + decoder->pads[i].sig_type = PAD_SIGNAL_ANALOG; > + } else { > + decoder->pads[i].flags = MEDIA_PAD_FL_SOURCE; > + decoder->pads[i].sig_type = PAD_SIGNAL_DV; > + } > + } > + ret = media_entity_pads_init(&sd->entity, TVP5150_NUM_PADS, > + decoder->pads); > + if (ret < 0) > + return ret; > + > + /* in case of no oftree support */ > + if (!decoder->endpoints[0]) > + return 0; Hmm... > + > + /* Allocate and initialize all available input connectors */ > + decoder->connectors = devm_kcalloc(dev, decoder->connectors_num, > + sizeof(*decoder->connectors), > + GFP_KERNEL); > + if (!decoder->connectors) > + return -ENOMEM; > + > + for (i = 0; i < decoder->connectors_num; i++) { > + struct device_node *rp; > + struct of_endpoint ep; > + > + rp = of_graph_get_remote_port_parent(decoder->endpoints[i]); > + of_graph_parse_endpoint(decoder->endpoints[i], &ep); > + decoder->connectors[i].port_num = ep.port; > + decoder->connectors[i].is_svideo = !!of_device_is_compatible(rp, > + "svideo-connector"); > + > + if (decoder->connectors[i].is_svideo) > + decoder->connectors[i].ent.function = > + MEDIA_ENT_F_CONN_SVIDEO; > + else > + decoder->connectors[i].ent.function = > + MEDIA_ENT_F_CONN_COMPOSITE; > + > + decoder->connectors[i].ent.flags = MEDIA_ENT_FL_CONNECTOR; > + ret = of_property_read_string(rp, "label", > + &decoder->connectors[i].ent.name); > + if (ret < 0) > + return ret; I would prefer, instead, to have a separate routine for OF. I'll probably use something like the above for the non-DT devices (e. g. the ones using em28xx driver). > + } > +#endif > + return 0; > +} > + > +static bool tvp5150_valid_input(struct device_node *endpoint, > + unsigned int port, unsigned int id) Please call it as tvp5150_of_valid_input(). We may need something similar for devices based on em28xx (passing info via platform_data). > +{ > + struct device_node *rp = of_graph_get_remote_port_parent(endpoint); > + const char *input; > + int ret; > + > + /* perform some basic checks needed for later mc_init */ > + switch (port) { > + case TVP5150_PAD_AIP1A: > + /* svideo must be connected to endpoint@1 */ > + ret = id ? of_device_is_compatible(rp, "svideo-connector") : > + of_device_is_compatible(rp, "composite-video-connector"); > + if (!ret) > + return false; > + break; > + case TVP5150_PAD_AIP1B: > + ret = of_device_is_compatible(rp, "composite-video-connector"); > + if (!ret) > + return false; > + break; > + } > + > + ret = of_property_read_string(rp, "label", &input); > + if (ret < 0) > + return false; > + > + return true; > +} > > - flags = bus_cfg.bus.parallel.flags; > +static int tvp5150_parse_dt(struct tvp5150 *decoder, struct device_node *np) > +{ > + struct device *dev = decoder->sd.dev; > + struct v4l2_fwnode_endpoint bus_cfg; > + struct device_node *ep_np; > + unsigned int flags; > + int ret, i = 0, in = 0; > + bool found = false; > > - if (bus_cfg.bus_type == V4L2_MBUS_PARALLEL && > - !(flags & V4L2_MBUS_HSYNC_ACTIVE_HIGH && > - flags & V4L2_MBUS_VSYNC_ACTIVE_HIGH && > - flags & V4L2_MBUS_FIELD_EVEN_LOW)) { > + /* at least 1 output and 1 input */ > + decoder->endpoints_num = of_graph_get_endpoint_count(np); > + if (decoder->endpoints_num < 2 || decoder->endpoints_num > 4) { > ret = -EINVAL; > goto err; > } > > - decoder->mbus_type = bus_cfg.bus_type; > + for_each_endpoint_of_node(np, ep_np) { > + struct of_endpoint ep; > > + of_graph_parse_endpoint(ep_np, &ep); > + if (decoder->endpoints[i]) { > + /* this should never happen */ > + dev_err(dev, "Invalid endpoint %pOF on port %d\n", > + ep.local_node, ep.port); > + ret = -EINVAL; > + goto err; > + } > + > + switch (ep.port) { > + case TVP5150_PAD_AIP1A: > + case TVP5150_PAD_AIP1B: > + if (!tvp5150_valid_input(ep_np, ep.port, ep.id)) { > + dev_err(dev, > + "Invalid endpoint %pOF on port %d\n", > + ep.local_node, ep.port); > + ret = -EINVAL; > + goto err; > + } > + in++; > + break; > + case TVP5150_PAD_VID_OUT: > + ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep_np), > + &bus_cfg); > + if (ret) > + goto err; > + > + flags = bus_cfg.bus.parallel.flags; > + > + if (bus_cfg.bus_type == V4L2_MBUS_PARALLEL && > + !(flags & V4L2_MBUS_HSYNC_ACTIVE_HIGH && > + flags & V4L2_MBUS_VSYNC_ACTIVE_HIGH && > + flags & V4L2_MBUS_FIELD_EVEN_LOW)) { > + ret = -EINVAL; > + goto err; > + } > + > + decoder->mbus_type = bus_cfg.bus_type; > + break; > + default: > + dev_err(dev, "Invalid port %d for endpoint %pOF\n", > + ep.port, ep.local_node); > + ret = -EINVAL; > + goto err; > + } > + > + of_node_get(ep_np); > + decoder->endpoints[i] = ep_np; > + i++; > + > + found = true; > + } > + > + decoder->connectors_num = in; > + return found ? 0 : -ENODEV; > err: > - of_node_put(ep); > return ret; > } > > +static void tvp5150_dt_cleanup(struct tvp5150 *decoder) > +{ > + unsigned int i; > + > + for (i = 0; i < TVP5150_NUM_PADS; i++) > + of_node_put(decoder->endpoints[i]); > +} > + > static const char * const tvp5150_test_patterns[2] = { > "Disabled", > "Black screen" > @@ -1586,7 +1933,7 @@ static int tvp5150_probe(struct i2c_client *c, > res = tvp5150_parse_dt(core, np); > if (res) { > dev_err(sd->dev, "DT parsing error: %d\n", res); > - return res; > + goto err_cleanup_dt; > } > } else { > /* Default to BT.656 embedded sync */ > @@ -1594,25 +1941,16 @@ static int tvp5150_probe(struct i2c_client *c, > } > > v4l2_i2c_subdev_init(sd, c, &tvp5150_ops); > + sd->internal_ops = &tvp5150_internal_ops; > sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; > > -#if defined(CONFIG_MEDIA_CONTROLLER) > - core->pads[TVP5150_PAD_IF_INPUT].flags = MEDIA_PAD_FL_SINK; > - core->pads[TVP5150_PAD_IF_INPUT].sig_type = PAD_SIGNAL_ANALOG; > - core->pads[TVP5150_PAD_VID_OUT].flags = MEDIA_PAD_FL_SOURCE; > - core->pads[TVP5150_PAD_VID_OUT].sig_type = PAD_SIGNAL_DV; > - > - sd->entity.function = MEDIA_ENT_F_ATV_DECODER; > - > - res = media_entity_pads_init(&sd->entity, TVP5150_NUM_PADS, core->pads); > - if (res < 0) > - return res; > - > -#endif > + res = tvp5150_mc_init(sd); > + if (res) > + goto err_cleanup_dt; > > res = tvp5150_detect_version(core); > if (res < 0) > - return res; > + goto err_cleanup_dt; > > core->norm = V4L2_STD_ALL; /* Default is autodetect */ > core->detected_norm = V4L2_STD_UNKNOWN; > @@ -1664,6 +2002,9 @@ static int tvp5150_probe(struct i2c_client *c, > err: > v4l2_ctrl_handler_free(&core->hdl); > return res; > +err_cleanup_dt: > + tvp5150_dt_cleanup(core); > + return res; > } > > static int tvp5150_remove(struct i2c_client *c) Thanks, Mauro -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
