Hi Rob, > From: Rob Herring, Sent: Tuesday, December 19, 2017 9:10 AM > > On Sun, Dec 17, 2017 at 11:16 PM, Yoshihiro Shimoda > <yoshihiro.shimoda.uh@xxxxxxxxxxx> wrote: > > Hi Rob, > > > > Thank you for your comments! > > > >> From: Rob Herring, Sent: Sunday, December 17, 2017 3:05 AM > >> > >> On Fri, Dec 15, 2017 at 02:45:26PM +0900, Yoshihiro Shimoda wrote: > >> > Some R-Car SoCs (e.g. R-Car D3) doesn't have dedicated pins of VBUS > >> > and ID. So, they may be connected to gpio pins. To handle the gpio > >> > pins, this patch adds the handling of VBUS and ID pins instead of > >> > dedicated pins. > >> > > >> > Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@xxxxxxxxxxx> > >> > --- > >> > .../devicetree/bindings/phy/rcar-gen3-phy-usb2.txt | 2 + > >> > drivers/phy/renesas/phy-rcar-gen3-usb2.c | 77 ++++++++++++++++++++-- > >> > 2 files changed, 72 insertions(+), 7 deletions(-) > >> > > >> > diff --git a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt > >> b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt > >> > index 99b651b..999a6ef 100644 > >> > --- a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt > >> > +++ b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt > >> > @@ -27,6 +27,8 @@ channel as USB OTG: > >> > - interrupts: interrupt specifier for the PHY. > >> > - vbus-supply: Phandle to a regulator that provides power to the VBUS. This > >> > regulator will be managed during the PHY power on/off sequence. > >> > +- vbus-gpios: use gpio to control vbus instead of dedicated pin. > >> > >> How does this relate to vbus-supply? A gpio-regulator doesn't work here? > > > > Thank you for the pointed out. You're correct. A gpio-regulator can work intead of "vbus-gpios". > > So, I will drop this. > > > >> > +- id-gpios: use gpio to detect id instead of dedicated pin. > >> > >> These aren't part of the phy, but really belong in a connector node. > > > > I'm afraid but I don't understand "a connector node" mean. > > Is it an extcon device for instance? > > If so, I'll try to use extcon-usb-gpio.c instead of own gpio handling on the driver. > > No, extcon binding has a lot of Linuxisms in it. I mean something like > hdmi-connector binding. Thank you for the reply! I understood it. The hdmi-connector binding has "hdp-gpios". And, this is similar with "id-gpios" of usb. > There's been some attempts[1] for USB connectors, but nothing finalized. > > Rob > > [1] https://www.spinics.net/lists/linux-usb/msg161104.html This means I should finalize the USB connectors binding at first? I checked the email archive, but it seems hard to finalize though... Best regards, Yoshihiro Shimoda ��.n��������+%������w��{.n����z�{��ܨ}���Ơz�j:+v�����w����ޙ��&�)ߡ�a����z�ޗ���ݢj��w�f
