Re: [RFC 3/6] dt/bindings: Add bindings for Tegra20/30 NOR bus driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On Mon, Jul 25, 2016 at 02:09:18PM +0100, Jon Hunter wrote:
> 
> On 25/07/16 13:10, Thierry Reding wrote:
> > * PGP Signed by an unknown key
> > 
> > On Thu, Jul 21, 2016 at 10:10:49PM +0200, Mirza Krak wrote:
> >> 2016-07-21 11:56 GMT+02:00 Jon Hunter <jonathanh@xxxxxxxxxx>:
> >>>> +
> >>>> +The NOR controller supports a number of memory types, including synchronous NOR,
> >>>> +asynchronous NOR, and other flash memories with similar interfaces, such as
> >>>> +MuxOneNAND. One could also connect high speed devices like FPGAs, DSPs,
> >>>> +CAN chips, Wi-Fi chips etc.
> >>>
> >>> Nit-pick ... the Tegra documentation refers to this controller as the
> >>> GMI (general memory interface) or SNOR (sync-NOR) controller because it
> >>> is not just limited to NOR as you mentioned. I see references to GMI in
> >>> the Tegra pinctrl driver and so may be we should use this name.
> >>
> >> ACK.
> >>
> >>
> >>>> +Required properties:
> >>>> +
> >>>> + - compatible: should be "nvidia,tegra20-nor", "nvidia,tegra30-nor"
> >>>
> >>> I see at least one difference at the register level between Tegra20 and
> >>> Tegra30 and so I think this should be something like ...
> >>>
> >>>  - compatible : Should contain one of the following:
> >>>         For Tegra20 must contain "nvidia,tegra20-gmi".
> >>>         For Tegra30 must contain "nvidia,tegra30-gmi".
> >>
> >> ACK. Just curious, which register was it? I only checked that they
> >> have the same count of registers.
> >>
> >>>> + - nvidia,config: This property represents the SNOR_CONFIG_0 register.
> >>>
> >>> There is also a SNOR_MIO_CONFIG for the MIO address space and so I think
> >>> that this should be nvidia,snor-config to be explicit. It might be nice
> >>> to also add a "nvidia,mio-config" while you are at it as well, however,
> >>> that could always be done later. If you do, then the
> >>> "nvidia,snor-config" becomes optional depending on whether you are using
> >>> the SNOR or MIO address space.
> >>
> >> ACK the nvidia,snor-config part, will though wait for further comments
> >> regarding what to do with the config registers, break-out or keep it
> >> is a one property / register.
> >>
> >> Regarding mio-config, not sure about if I would like to include that
> >> part in this stage. If you feel strongly about this we can do it. If
> >> it only comes to down to replicate the same configurations that we do
> >> for SNOR to MIO then I do not see much of a problem, but would like
> >> SNOR to be accepted and would not like the MIO part to halt this. But
> >> then again this up to you guys.
> > 
> > What's the difference between SNOR and MIO? Sorry if I'm being dense but
> > a quick look around the internet didn't yield anything related. I'd be
> > happy to read up if somebody can provide a link.
> 
> I am not sure where this term MIO comes from (may be an NVIDIA term),
> but from looking at the MIO_CONFIG register, it looks like a basic
> 16/32-bit interface with configurable read/write strobe timing. Does not
> support bursting or address/data multiplexing that the SNOR interface
> does. So may be it is used for interfacing to external devices such as
> FIFOs, UARTs, I2C expanders, etc.

Yes, looks like some sort of parallel interface to connect external
devices and make them act like MMIO. Perhaps MIO is supposed to be
"memory I/O". I've found some vague references to MIO == multi-I/O,
but that was always related to serial flash (essentially something
like QSPI).

Thierry

Attachment: signature.asc
Description: PGP signature


[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux