Re: [RFC 3/6] dt/bindings: Add bindings for Tegra20/30 NOR bus driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On Thu, Jul 21, 2016 at 10:10:49PM +0200, Mirza Krak wrote:
> 2016-07-21 11:56 GMT+02:00 Jon Hunter <jonathanh@xxxxxxxxxx>:
> >> +
> >> +The NOR controller supports a number of memory types, including synchronous NOR,
> >> +asynchronous NOR, and other flash memories with similar interfaces, such as
> >> +MuxOneNAND. One could also connect high speed devices like FPGAs, DSPs,
> >> +CAN chips, Wi-Fi chips etc.
> >
> > Nit-pick ... the Tegra documentation refers to this controller as the
> > GMI (general memory interface) or SNOR (sync-NOR) controller because it
> > is not just limited to NOR as you mentioned. I see references to GMI in
> > the Tegra pinctrl driver and so may be we should use this name.
> 
> ACK.
> 
> 
> >> +Required properties:
> >> +
> >> + - compatible: should be "nvidia,tegra20-nor", "nvidia,tegra30-nor"
> >
> > I see at least one difference at the register level between Tegra20 and
> > Tegra30 and so I think this should be something like ...
> >
> >  - compatible : Should contain one of the following:
> >         For Tegra20 must contain "nvidia,tegra20-gmi".
> >         For Tegra30 must contain "nvidia,tegra30-gmi".
> 
> ACK. Just curious, which register was it? I only checked that they
> have the same count of registers.
> 
> >> + - nvidia,config: This property represents the SNOR_CONFIG_0 register.
> >
> > There is also a SNOR_MIO_CONFIG for the MIO address space and so I think
> > that this should be nvidia,snor-config to be explicit. It might be nice
> > to also add a "nvidia,mio-config" while you are at it as well, however,
> > that could always be done later. If you do, then the
> > "nvidia,snor-config" becomes optional depending on whether you are using
> > the SNOR or MIO address space.
> 
> ACK the nvidia,snor-config part, will though wait for further comments
> regarding what to do with the config registers, break-out or keep it
> is a one property / register.
> 
> Regarding mio-config, not sure about if I would like to include that
> part in this stage. If you feel strongly about this we can do it. If
> it only comes to down to replicate the same configurations that we do
> for SNOR to MIO then I do not see much of a problem, but would like
> SNOR to be accepted and would not like the MIO part to halt this. But
> then again this up to you guys.

What's the difference between SNOR and MIO? Sorry if I'm being dense but
a quick look around the internet didn't yield anything related. I'd be
happy to read up if somebody can provide a link.

> > I wonder if it is worth mentioning that the chip-select specified in the
> > "nvidia,config" prop should match that in the "ranges" prop unless you
> > have some external decoding logic to provide an external chip-select.
> > Which raises a question, what does the chip-select in the ranges
> > actually represent? I am not sure if there is a common practice here for
> > device tree when boards have external logic to provide additional
> > chip-selects. I am sure this is quite common.
> 
> I do not understand why CS pin setting in nvidia,config need to match
> the "ranges" prop? Other then maybe cosmetics.
> 
> If we do not have any external decoding logic to create more
> chip-selects we only have ONE chip-select, and that one should always
> be indexed as 0? Regardless of which CS pin is used. Because
> ultimately what we configure in SNOR_CONFIG is which PIN(function) to
> use as chip-select. The address space remains the same.

Is that really so? Looking at the list of pins there are 8 CS outputs
from the GMI controller. That and the presence of the SNOR_SEL field in
the SNOR_CONFIG_0 register indicate to me that you can use software to
assert any of the CS outputs (though only one at the same time, which
makes sense since you want to avoid writing to multiple chips at once).

Of course the documentation is to blame here, it doesn't go into any
detail at all about how to use the GMI controller.

Thierry

Attachment: signature.asc
Description: PGP signature


[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux