I faced the same problem a few days ago. The E1 looks like ok, no slips, frame errors, etc. But the IRQ misses increases a lot, and the links never comes up. On May 29, 2012, at 5:10 AM, Kaloyan Kovachev wrote: > On Mon, 28 May 2012 18:40:27 -0700 (PDT), Marcus Vinicius > <marc_mcs10 at yahoo.com.br> wrote: >> Hi, >> >> I run ss7linktest with information sent me by telco, but I get the same >> error: >> >> >> ./ss7linktest 16 itu 781 678 >> >> Starting link 1 >> Link state change: IDLE -> NOTALIGNED >> Len = 4 [ ff ff 01 00 ] >> FSN: 127 FIB 1 >> BSN: 127 BIB 1 >>> [0] LSSU SIO >> >> Len = 4 [ ff ff 01 00 ] >> FSN: 127 FIB 1 >> BSN: 127 BIB 1 >> <[0] LSSU SIO >> >> Link state change: NOTALIGNED -> ALIGNED >> Len = 4 [ ff ff 01 02 ] >> FSN: 127 FIB 1 >> BSN: 127 BIB 1 >>> [0] LSSU SIE >> >> Len = 4 [ ff ff 01 02 ] >> FSN: 127 FIB 1 >> BSN: 127 BIB 1 >> <[0] LSSU SIE >> >> Link state change: ALIGNED -> PROVING >> Len = 4 [ ff ff 01 03 ] >> FSN: 127 FIB 1 >> BSN: 127 BIB 1 >> <[0] LSSU SIOS > > Here the other end is closing the connection - noting wrong on your side. > Is the link enabled (and properly configured) at telco side? > >> >> Link state change: PROVING -> IDLE >> Link state change: IDLE -> NOTALIGNED >> Len = 4 [ ff ff 01 00 ] >> FSN: 127 FIB 1 >> BSN: 127 BIB 1 >>> [0] LSSU SIO >> >> Len = 4 [ ff ff 01 00 ] >> FSN: 127 FIB 1 >> BSN: 127 BIB 1 >> <[0] LSSU SIO >> >> Link state change: NOTALIGNED -> ALIGNED >> Len = 4 [ ff ff 01 02 ] >> FSN: 127 FIB 1 >> BSN: 127 BIB 1 >>> [0] LSSU SIE >> >> Len = 4 [ ff ff 01 02 ] >> FSN: 127 FIB 1 >> BSN: 127 BIB 1 >> <[0] LSSU SIE >> >> Link state change: ALIGNED -> PROVING >> Len = 4 [ ff ff 01 03 ] >> FSN: 127 FIB 1 >> BSN: 127 BIB 1 >> <[0] LSSU SIOS >> >> Link state change: PROVING -> IDLE >> Link state change: IDLE -> NOTALIGNED >> Len = 4 [ ff ff 01 00 ] >> FSN: 127 FIB 1 >> BSN: 127 BIB 1 >>> [0] LSSU SIO >> >> >> >> I don't have any slip or crc error. The link looks good, but it can't > gets >> up; >> >> thanks >> >> -- >> Marcus >> >> >> >> >> ________________________________ >> De: Kaloyan Kovachev <kkovachev at varna.net> >> Para: Marcus Vinicius <marc_mcs10 at yahoo.com.br> >> Enviadas: Segunda-feira, 28 de Maio de 2012 11:27 >> Assunto: Re: [asterisk-ss7] ALIGNMENT Problem >> >> try ss7lintest from libss7 with asterisk stopped: >> ss7linktest 16 itu XXX YYY >> >> and see if it will align >> >> On Mon, 28 May 2012 07:05:10 -0700 (PDT), Marcus Vinicius >> <marc_mcs10 at yahoo.com.br> wrote: >>> Hello, >>> >>> The config are correct according from telco: >>> >>> >>> >>> signalling=ss7 >>> ss7type=itu >>> ss7_called_nai=dynamic >>> ss7_calling_nai=dynamic >>> networkindicator=national >>> pointcode=781 >>> >>> linkset=1 >>> pointcode=XXX >>> defaultdpc=YYY >>> adjpointcode=YYY >>> context=from-pstn-01 >>> >>> group=1 >>> cicbeginswith=1 >>> channel=>1-15 >>> >>> cicbeginswith=301 >>> channel=>17-31 >>> sigchan=16 >>> >>> >>> >>> I'll see the cables, but the link is UP: >>> >>> >>> Description Alarms IRQ bpviol CRC >> Fra >>> Codi Options LBO >>> AP408 Card 1 Span 1 OK 0 0 0 >> CCS >>> HDB3 0 db (CSU)/0-133 feet (DSX-1) >>> >>> >>> >>> Thanks a lot >>> >>> >>> -- >>> Marcus >>> >>> >>> >>> >>> ________________________________ >>> De: Kaloyan Kovachev <kkovachev at varna.net> >>> Para: Marcus Vinicius <marc_mcs10 at yahoo.com.br>; >>> asterisk-ss7 at lists.digium.com >>> Enviadas: Segunda-feira, 28 de Maio de 2012 6:18 >>> Assunto: Re: [asterisk-ss7] ALIGNMENT Problem >>> >>> Hi, >>> >>> On Thu, 24 May 2012 06:47:28 -0700 (PDT), Marcus Vinicius >>> <marc_mcs10 at yahoo.com.br> wrote: >>>> Hi, >>>> >>>> I can't alignment a libss7 Asterisk with a TDM switch (Huawei/UMG) >>> because >>>> the link doesn't pass the "PROVING" state. >>>> >>>> All configurations are correct according from telco, but I always get >>> the >>>> same logs: >>> >>> check your cables and double check your config for the correct > signaling >>> channel > > -- > _____________________________________________________________________ > -- Bandwidth and Colocation Provided by http://www.api-digital.com -- > > asterisk-ss7 mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-ss7
|