Hi all,
Did ask for some help recently in trying to get an RME Multiface working
under Alsa, Suse and using the PCMCIA card. It seems to be working for many
of you. Have managed to get a certain distance, again, and have reached
aother brickwall. Firstly I recompiled the kernel (several times) reducing
the modules and size and only loading the things I need (a minimal system).
I then recompiled the modules, installed them and everything seems to be
hunky-dory but...
The card appears to be recognised by the system, the red light on the front
of the breakout box does extinguish on startup as expected (and even
extinguishes when inserting the card while the system is running, which
surprised me). I've used the modules.d/sound script for the hdsp as
suggested in several emails and websites. The problem is the card doesn't
appear in Jack, Qjackctl or many other things. Whilst "hdspconf" works fine
and even under a shell recognising the card and responding, "hdsploader"
does not (refer listing #1 below), I get the same error message I received
before. I have read that I need to use Version 10 of the pcmcia card
firmware (I'm running version 11) but have no method of moving back to the
old firmware (despite what everybody says there appears to be no software on
the RME site that allows one to go backwards and I have all of the old
loader programmes on my harddrive anyway). Are there other commands
required when loading the module (hdsp.ko)? where do they go? What other
commands are needed to get the box to work?
Interestingly the listing from dmesg shows the card being recognised by the
system...
pccard: CardBus card inserted into slot 0
PCI: Enabling device 0000:03:00.0 (0080 -> 0082)
ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [C0B8] -> GSI 11 (level, low) ->
IRQ 11
ALSA sound/pci/rme9652/hdsp.c:771: Hammerfall-DSP: wait for FIFO status <= 0
failed after 30 iterations
ALSA sound/pci/rme9652/hdsp.c:650: Hammerfall-DSP: loading firmware
ALSA sound/pci/rme9652/hdsp.c:683: Hammerfall-DSP: finished firmware loading
...although clearly something there isn't working ("failed after 30
iterations") and it does seem to to be loading the firmware. And further
down in the listing...
ALSA sound/pci/rme9652/hdsp.c:4948: Hammerfall-DSP: Firmware already
present, initializing card.
....
How do I get this to work? Can anybody help here?
I'm not a programmer just a recording engineer and musician that would like
to get this up and running. Whilst I am a devotee of linux, normally, this
is one area that it does fall down particularly when it seems to work for
many people but not for others. I'm sure it's quite simple, really. Given
the frustration, I might just go back to using Windows and Cubase, at least
this works (most of the time) and straight out of the box. I need to try to
get this portable running by Sat (2nd Dec) to record a gig.
Thanks in advance,
Tim.
mailto:timbarker@xxxxxxxxxxxxxx
--------------------------------------------------------
Listing 1:
--------------------------------------------------------
#hdspconf
HDSPConf 1.4 - Copyright (C) 2003 Thomas Charbonnel <thomas@xxxxxxxxxx>
This program comes WITH ABSOLUTELY NO WARRANTY
HDSPConf is free software, see the file copying for details
Looking for HDSP cards :
Card 0 : Intel 82801CA-ICH3 with AD1886A at 0x4000, irq 5
Card 1 : RME Hammerfall DSP + Multiface at 0x24000000, irq 11
Multiface found !
1 Hammerfall DSP card found.
!
! at this point the hdspconf dialog box appears on the desktop
!
#hdsploader
hdsploader - firmware loader for RME Hammerfall DSP cards
Looking for HDSP + Multiface or Digiface cards :
Card 0 : Intel 82801CA-ICH3 with AD1886A at 0x4000, irq 5
Card 1 : RME Hammerfall DSP + Multiface at 0x24000000, irq 11
Upload firmware for card hw:1
!
! at this point the following error message appears
!
hwdep ioctl error on card hw:1 : Device or resource busy
---------------------------------------------------------
Listing 2: some of the background
---------------------------------------------------------
#lspci -n
00:00.0 Class 0600: 8086:1a30 (rev 04)
00:01.0 Class 0604: 8086:1a31 (rev 04)
00:1e.0 Class 0604: 8086:2448 (rev 42)
00:1f.0 Class 0601: 8086:248c (rev 02)
00:1f.1 Class 0101: 8086:248a (rev 02)
00:1f.5 Class 0401: 8086:2485 (rev 02)
01:00.0 Class 0300: 1002:4c57
02:04.0 Class 0780: 11c1:0450 (rev 02)
02:05.0 Class 0c00: 104c:8023
02:06.0 Class 0607: 104c:ac50 (rev 02)
02:08.0 Class 0200: 8086:1031 (rev 42)
02:0e.0 Class 0c03: 1033:0035 (rev 41)
02:0e.1 Class 0c03: 1033:0035 (rev 41)
02:0e.2 Class 0c03: 1033:00e0 (rev 02)
03:00.0 Class 0401: 10ee:3fc5 (rev 0b)
#lspci -v
00:00.0 Host bridge: Intel Corporation 82845 845 (Brookdale) Chipset Host
Bridge (rev 04)
Subsystem: Compaq Computer Corporation Unknown device 004e
Flags: bus master, fast devsel, latency 0
Memory at 60000000 (32-bit, prefetchable) [size=256M]
Capabilities: [e4] Vendor Specific Information
Capabilities: [a0] AGP version 2.0
00:01.0 PCI bridge: Intel Corporation 82845 845 (Brookdale) Chipset AGP
Bridge (rev 04) (prog-if 00 [Normal decode])
Flags: bus master, 66MHz, fast devsel, latency 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: 40400000-404fffff
Prefetchable memory behind bridge: 48000000-4fffffff
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 42)
(prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=03, sec-latency=32
I/O behind bridge: 00002000-00002fff
Memory behind bridge: 40000000-403fffff
Prefetchable memory behind bridge: 20000000-21ffffff
00:1f.0 ISA bridge: Intel Corporation 82801CAM ISA Bridge (LPC) (rev 02)
Flags: bus master, medium devsel, latency 0
00:1f.1 IDE interface: Intel Corporation 82801CAM IDE U100 (rev 02) (prog-if
8a [Master SecP PriP])
Subsystem: Compaq Computer Corporation Unknown device 004e
Flags: bus master, medium devsel, latency 0, IRQ 11
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at 4440 [size=16]
Memory at 22000000 (32-bit, non-prefetchable) [size=1K]
00:1f.5 Multimedia audio controller: Intel Corporation 82801CA/CAM AC'97
Audio Controller (rev 02)
Subsystem: Compaq Computer Corporation Unknown device 004e
Flags: bus master, medium devsel, latency 0, IRQ 5
I/O ports at 4000 [size=256]
I/O ports at 4400 [size=64]
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M7
LW [Radeon Mobility 7500] (prog-if 00 [VGA])
Subsystem: Compaq Computer Corporation Unknown device 004e
Flags: bus master, stepping, 66MHz, medium devsel, latency 66, IRQ
11
Memory at 48000000 (32-bit, prefetchable) [size=128M]
I/O ports at 3000 [size=256]
Memory at 40400000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at 40420000 [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Capabilities: [50] Power Management version 2
02:04.0 Communication controller: Agere Systems LT WinModem (rev 02)
Subsystem: AMBIT Microsystem Corp. Evo N600c
Flags: bus master, medium devsel, latency 66, IRQ 5
Memory at 40300000 (32-bit, non-prefetchable) [size=256]
I/O ports at 2440 [size=8]
I/O ports at 2000 [size=256]
Capabilities: [f8] Power Management version 2
02:05.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000
Controller (PHY/Link) (prog-if 10 [OHCI])
Subsystem: Toshiba America Info Systems Unknown device ff01
Flags: bus master, medium devsel, latency 66, IRQ 11
Memory at 40280000 (32-bit, non-prefetchable) [size=2K]
Memory at 40000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
02:06.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller
(rev 02)
Subsystem: Compaq Computer Corporation Unknown device 004e
Flags: bus master, medium devsel, latency 168, IRQ 11
Memory at 40080000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 20000000-21fff000 (prefetchable)
Memory window 1: 24000000-25fff000
I/O window 0: 00002800-000028ff
I/O window 1: 00002c00-00002cff
16-bit legacy interface ports at 0001
02:08.0 Ethernet controller: Intel Corporation 82801CAM (ICH3) PRO/100 VE
(LOM) Ethernet Controller (rev 42)
Subsystem: Compaq Computer Corporation Unknown device 004e
Flags: bus master, medium devsel, latency 66, IRQ 10
Memory at 40100000 (32-bit, non-prefetchable) [size=4K]
I/O ports at 2400 [size=64]
Capabilities: [dc] Power Management version 2
02:0e.0 USB Controller: NEC Corporation USB (rev 41) (prog-if 10 [OHCI])
Subsystem: Compaq Computer Corporation Unknown device 004e
Flags: bus master, medium devsel, latency 64, IRQ 10
Memory at 40180000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
02:0e.1 USB Controller: NEC Corporation USB (rev 41) (prog-if 10 [OHCI])
Subsystem: Compaq Computer Corporation Unknown device 004e
Flags: bus master, medium devsel, latency 64, IRQ 10
Memory at 40200000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
02:0e.2 USB Controller: NEC Corporation USB 2.0 (rev 02) (prog-if 20 [EHCI])
Subsystem: Compaq Computer Corporation Unknown device 004e
Flags: bus master, medium devsel, latency 64, IRQ 10
Memory at 40380000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
03:00.0 Multimedia audio controller: Xilinx Corporation RME Hammerfall DSP
(rev 0b)
Flags: bus master, stepping, medium devsel, latency 255, IRQ 11
Memory at 24000000 (32-bit, non-prefetchable) [size=64K]
#lsmod
Module Size Used by
nls_cp850 5120 1
nls_utf8 2176 1
smbfs 56952 2
joydev 9152 0
snd_seq_dummy 3844 0
af_packet 19848 2
cpufreq_ondemand 6304 1
cpufreq_userspace 3988 0
cpufreq_powersave 1920 0
acpi_cpufreq 5640 1
ipv6 220672 18
snd_pcm_oss 43392 0
snd_mixer_oss 16512 1 snd_pcm_oss
snd_seq_midi 9216 0
snd_seq_midi_event 6784 1 snd_seq_midi
snd_seq 48368 4
snd_seq_dummy,snd_seq_midi,snd_seq_midi_event
button 6928 0
battery 9732 0
ac 5124 0
apparmor 49180 0
aamatch_pcre 13568 1 apparmor
loop 14600 0
dm_mod 47800 0
hdsp 41860 1
snd_rawmidi 23680 2 snd_seq_midi,hdsp
snd_seq_device 8204 4
snd_seq_dummy,snd_seq_midi,snd_seq,snd_rawmidi
snd_hwdep 8964 1 hdsp
usbhid 40288 0
pcmcia 35132 0
firmware_class 9984 2 hdsp,pcmcia
i8xx_tco 7060 0
intel_agp 21148 1
agpgart 29488 1 intel_agp
shpchp 39872 0
pci_hotplug 24628 1 shpchp
yenta_socket 24204 2
rsrc_nonstatic 12416 1 yenta_socket
pcmcia_core 37264 3 pcmcia,yenta_socket,rsrc_nonstatic
ohci_hcd 17540 0
snd_intel8x0 30364 5
snd_ac97_codec 83232 1 snd_intel8x0
snd_ac97_bus 2304 1 snd_ac97_codec
snd_pcm 81288 5 snd_pcm_oss,hdsp,snd_intel8x0,snd_ac97_codec
snd_timer 21380 3 snd_seq,snd_pcm
snd 51716 24
snd_seq_dummy,snd_pcm_oss,snd_mixer_oss,snd_seq_midi,snd_seq,hdsp,snd_rawmid
i,snd_seq_device,snd_hwdep,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer
soundcore 8928 1 snd
snd_page_alloc 9864 3 hdsp,snd_intel8x0,snd_pcm
ehci_hcd 27272 0
ohci1394 30000 0
ieee1394 89016 1 ohci1394
ide_cd 35360 0
usbcore 110980 4 usbhid,ohci_hcd,ehci_hcd
cdrom 32544 1 ide_cd
parport_pc 35172 1
lp 10948 0
parport 32200 2 parport_pc,lp
ext3 119048 6
jbd 55200 1 ext3
fan 4740 0
thermal 13832 0
processor 23108 2 acpi_cpufreq,thermal
piix 9220 0 [permanent]
ide_disk 14976 8
ide_core 117692 3 ide_cd,piix,ide_disk
#more /proc/interrupts
CPU0
0: 37695685 XT-PIC timer
1: 2362 XT-PIC i8042
2: 0 XT-PIC cascade
5: 89103 XT-PIC Intel 82801CA-ICH3
7: 1 XT-PIC parport0
8: 2 XT-PIC rtc
9: 396781 XT-PIC acpi
10: 169457 XT-PIC ehci_hcd:usb1, ohci_hcd:usb2,
ohci_hcd:usb3, eth0
11: 10 XT-PIC ohci1394, yenta, hdsp
12: 1802 XT-PIC i8042
14: 147607 XT-PIC ide0
15: 1340696 XT-PIC ide1
NMI: 0
LOC: 0
ERR: 0
MIS: 0
#more /proc/modules
nls_cp850 5120 1 - Live 0xd0e91000
nls_utf8 2176 1 - Live 0xd0e8f000
smbfs 56952 2 - Live 0xd0ea0000
joydev 9152 0 - Live 0xd0e8b000
snd_seq_dummy 3844 0 - Live 0xd0834000
af_packet 19848 2 - Live 0xd12d9000
cpufreq_ondemand 6304 1 - Live 0xd12cf000
cpufreq_userspace 3988 0 - Live 0xd10db000
cpufreq_powersave 1920 0 - Live 0xd1166000
acpi_cpufreq 5640 1 - Live 0xd11fd000
ipv6 220672 18 - Live 0xd130f000
snd_pcm_oss 43392 0 - Live 0xd1245000
snd_mixer_oss 16512 1 snd_pcm_oss, Live 0xd12c9000
snd_seq_midi 9216 0 - Live 0xd1241000
snd_seq_midi_event 6784 1 snd_seq_midi, Live 0xd11fa000
snd_seq 48368 4 snd_seq_dummy,snd_seq_midi,snd_seq_midi_event, Live
0xd12bc000
button 6928 0 - Live 0xd10b9000
battery 9732 0 - Live 0xd11c6000
ac 5124 0 - Live 0xd1101000
apparmor 49180 0 - Live 0xd1251000
aamatch_pcre 13568 1 apparmor, Live 0xd11ef000
loop 14600 0 - Live 0xd11ea000
dm_mod 47800 0 - Live 0xd11d1000
hdsp 41860 1 - Live 0xd11de000
snd_rawmidi 23680 2 snd_seq_midi,hdsp, Live 0xd11ca000
snd_seq_device 8204 4 snd_seq_dummy,snd_seq_midi,snd_seq,snd_rawmidi, Live
0xd11bd000
snd_hwdep 8964 1 hdsp, Live 0xd11b9000
usbhid 40288 0 - Live 0xd11a3000
pcmcia 35132 0 - Live 0xd11af000
firmware_class 9984 2 hdsp,pcmcia, Live 0xd119f000
i8xx_tco 7060 0 - Live 0xd1192000
intel_agp 21148 1 - Live 0xd115f000
agpgart 29488 1 intel_agp, Live 0xd1156000
shpchp 39872 0 - Live 0xd112d000
pci_hotplug 24628 1 shpchp, Live 0xd1144000
yenta_socket 24204 2 - Live 0xd10cc000
rsrc_nonstatic 12416 1 yenta_socket, Live 0xd111f000
pcmcia_core 37264 3 pcmcia,yenta_socket,rsrc_nonstatic, Live 0xd1139000
ohci_hcd 17540 0 - Live 0xd1119000
snd_intel8x0 30364 5 - Live 0xd1124000
snd_ac97_codec 83232 1 snd_intel8x0, Live 0xd10eb000
snd_ac97_bus 2304 1 snd_ac97_codec, Live 0xd10b7000
snd_pcm 81288 5 snd_pcm_oss,hdsp,snd_intel8x0,snd_ac97_codec, Live
0xd1104000
snd_timer 21380 3 snd_seq,snd_pcm, Live 0xd10d4000
snd 51716 24
snd_seq_dummy,snd_pcm_oss,snd_mixer_oss,snd_seq_midi,snd_seq,hdsp,snd_rawmid
i,snd_seq_device,snd_hwdep,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer,
Live 0xd10dd000
soundcore 8928 1 snd, Live 0xd10c8000
snd_page_alloc 9864 3 hdsp,snd_intel8x0,snd_pcm, Live 0xd10bc000
ehci_hcd 27272 0 - Live 0xd10c0000
ohci1394 30000 0 - Live 0xd10ac000
ieee1394 89016 1 ohci1394, Live 0xd106d000
ide_cd 35360 0 - Live 0xd1063000
usbcore 110980 4 usbhid,ohci_hcd,ehci_hcd, Live 0xd1085000
cdrom 32544 1 ide_cd, Live 0xd1033000
parport_pc 35172 1 - Live 0xd1029000
lp 10948 0 - Live 0xd0850000
parport 32200 2 parport_pc,lp, Live 0xd1020000
ext3 119048 6 - Live 0xd1044000
jbd 55200 1 ext3, Live 0xd086e000
fan 4740 0 - Live 0xd0825000
thermal 13832 0 - Live 0xd084b000
processor 23108 2 acpi_cpufreq,thermal, Live 0xd0854000
piix 9220 0 [permanent], Live 0xd082d000
ide_disk 14976 8 - Live 0xd0828000
ide_core 117692 3 ide_cd,piix,ide_disk, Live 0xd1002000
#lsmod | grep snd
snd_seq_dummy 3844 0
snd_pcm_oss 43392 0
snd_mixer_oss 16512 1 snd_pcm_oss
snd_seq_midi 9216 0
snd_seq_midi_event 6784 1 snd_seq_midi
snd_seq 48368 4
snd_seq_dummy,snd_seq_midi,snd_seq_midi_event
snd_rawmidi 23680 2 snd_seq_midi,hdsp
snd_seq_device 8204 4
snd_seq_dummy,snd_seq_midi,snd_seq,snd_rawmidi
snd_hwdep 8964 1 hdsp
snd_intel8x0 30364 5
snd_ac97_codec 83232 1 snd_intel8x0
snd_ac97_bus 2304 1 snd_ac97_codec
snd_pcm 81288 5 snd_pcm_oss,hdsp,snd_intel8x0,snd_ac97_codec
snd_timer 21380 3 snd_seq,snd_pcm
snd 51716 24
snd_seq_dummy,snd_pcm_oss,snd_mixer_oss,snd_seq_midi,snd_seq,hdsp,snd_rawmid
i,snd_seq_device,snd_hwdep,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer
soundcore 8928 1 snd
snd_page_alloc 9864 3 hdsp,snd_intel8x0,snd_pcm
#cat /proc/asound/cards
0 [I82801CAICH3 ]: ICH - Intel 82801CA-ICH3
Intel 82801CA-ICH3 with AD1886A at 0x4000, irq 5
1 [DSP ]: H-DSP - Hammerfall DSP
RME Hammerfall DSP + Multiface at 0x24000000, irq 11
#fuser /dev/dsp
#fuser /dev/snd/*/
/dev/snd/controlC0: 8658 8677
/dev/snd/controlC1: 8677
/dev/snd/pcmC0D0p: 8658m 8675m
/dev/snd/seq: 3376
/dev/snd/timer: 8658
#cat /etc/modprobe.d/sound
options snd-hdsp index=1
options snd-intel8x0 index=0
alias snd-card-0 snd-intel8x0
alias snd-card-1 snd-hdsp
alias char-major-116 snd
alias char-major-14 soundcore
alias snd-slot-0 snd-card-0
alias snd-slot-1 snd-card-1
alias snd-service-0-0 snd-mixer-oss
alias snd-service-0-1 snd-seq-oss
alias snd-service-0-3 snd-pcm-oss
alias snd-service-0-8 snd-seq-oss
alias snd-service-0-12 snd-pcm-oss
alias snd-service-1-0 snd-mixer-oss
alias snd-service-1-1 snd-seq-oss
alias snd-service-1-3 snd-pcm-oss
alias snd-service-1-8 snd-seq-oss
alias snd-service-1012 snd-pcm-oss
alias /dev/mixer snd-mixer-oss
alias /dev/dsp snd-pcm-oss
alias /dev/midi snd-seq-oss
options snd major=116 cards_limit=2
options hdsp enable=1
-----------------------------------------------------------
Listing 3: dmesg
-----------------------------------------------------------
#dmesg
Linux version 2.6.16.23.snd-0.25-default (geeko@buildhost) (gcc version
4.1.0 (SUSE Linux)) #1 Thu Nov 23 21:02:32 EST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000ffd0000 (usable)
BIOS-e820: 000000000ffd0000 - 000000000fff0c00 (reserved)
BIOS-e820: 000000000fff0c00 - 000000000fffc000 (ACPI NVS)
BIOS-e820: 000000000fffc000 - 0000000010000000 (reserved)
255MB LOWMEM available.
No mptable found.
On node 0 totalpages: 65488
DMA zone: 4096 pages, LIFO batch:0
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 61392 pages, LIFO batch:15
HighMem zone: 0 pages, LIFO batch:0
DMI 2.3 present.
IO/L-APIC allowed because system is MP or new enough
ACPI: RSDP (v000 COMPAQ ) @ 0x000f9970
ACPI: RSDT (v001 COMPAQ CPQ004A 0x25060220 CPQ 0x00000001) @ 0x0fff0c84
ACPI: FADT (v002 COMPAQ CPQ004A 0x00000002 CPQ 0x00000001) @ 0x0fff0c00
ACPI: SSDT (v001 COMPAQ CPQGysr 0x00001001 MSFT 0x0100000e) @ 0x0fff663b
ACPI: SSDT (v001 COMPAQ CPQCroc 0x00001001 MSFT 0x0100000e) @ 0x0fff6749
ACPI: DSDT (v001 COMPAQ EVON800 0x00010000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
Allocating PCI resources starting at 20000000 (gap: 10000000:f0000000)
Built 1 zonelists
Kernel command line: root=/dev/hda5 vga=0x317 resume=/ev/hda7 splash=silent
PROFILE=default
bootsplash: silent mode.
Local APIC disabled by BIOS -- you can enable it with "lapic"
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 1694.838 MHz processor.
Using tsc for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 254060k/261952k available (1472k kernel code, 7224k reserved, 598k
data, 148k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3394.67 BogoMIPS
(lpj=6789342)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 3febf9ff 00000000 00000000 00000000
00000000 00000000 00000000
CPU: After vendor identify, caps: 3febf9ff 00000000 00000000 00000000
00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: 3febf9ff 00000000 00000000 00000080 00000000
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
CPU: Intel(R) Pentium(R) 4 Mobile CPU 1.70GHz stepping 04
Checking 'hlt' instruction... OK.
checking if image is initramfs... it is
Freeing initrd memory: 2177k freed
not found!
ACPI: setting ELCR to 0200 (from 0c20)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS32 entry (0xc00f0000) in high memory, cannot use.
PCI: Using configuration type 1
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [C03B] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.C03B] bus is 0
PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 1100-113f claimed by ICH4 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #03 (-#06) is hidden behind transparent bridge #02 (-#03) (try
'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.C03B._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C03B.C03C._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C03B.C04D._PRT]
ACPI: Embedded Controller [C0CF] (gpe 29) interrupt mode.
ACPI: Power Resource [C142] (off)
ACPI: Power Resource [C156] (off)
ACPI: Power Resource [C15A] (off)
ACPI: Power Resource [C15E] (off)
ACPI: Power Resource [C167] (on)
ACPI: PCI Interrupt Link [C0B5] (IRQs 5 10 *11)
ACPI: PCI Interrupt Link [C0B6] (IRQs *5 10 11)
ACPI: PCI Interrupt Link [C0B7] (IRQs 5 10 *11)
ACPI: PCI Interrupt Link [C0B8] (IRQs 5 10 *11)
ACPI: PCI Interrupt Link [C0B9] (IRQs 5 *10 11)
ACPI Warning (pci_link-0118): Blank IRQ resource [20060127]
ACPI Error (pci_link-0163): Resource is not an IRQ entry
[20060127]
ACPI: PCI Interrupt Link [C0BA] (IRQs) *0, disabled.
ACPI Warning (pci_link-0118): Blank IRQ resource [20060127]
ACPI Error (pci_link-0163): Resource is not an IRQ entry
[20060127]
ACPI: PCI Interrupt Link [C0BB] (IRQs) *0, disabled.
ACPI Warning (pci_link-0118): Blank IRQ resource [20060127]
ACPI Error (pci_link-0163): Resource is not an IRQ entry
[20060127]
ACPI: PCI Interrupt Link [C0BC] (IRQs) *0, disabled.
ACPI: Power Resource [C0CE] (on)
ACPI: Power Resource [C1D3] (off)
ACPI: Power Resource [C1D4] (off)
ACPI: Power Resource [C1D5] (off)
ACPI: Power Resource [C1D6] (off)
ACPI: Power Resource [C1E1] (off)
ACPI: Power Resource [C1E2] (off)
ACPI: Power Resource [C1E3] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
TC classifier action (bugs to netdev@xxxxxxxxxxxxxxx cc hadi@xxxxxxxxxx)
Setting up standard PCI resources
pnp: 00:0d: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0d: ioport range 0x1000-0x107f could not be reserved
pnp: 00:0d: ioport range 0x1100-0x113f has been reserved
pnp: 00:0d: ioport range 0x1200-0x121f has been reserved
PCI: Bridge: 0000:00:01.0
IO window: 3000-3fff
MEM window: 40400000-404fffff
PREFETCH window: 48000000-4fffffff
PCI: Bus 3, cardbus bridge: 0000:02:06.0
IO window: 00002800-000028ff
IO window: 00002c00-00002cff
PREFETCH window: 20000000-21ffffff
MEM window: 24000000-25ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 2000-2fff
MEM window: 40000000-403fffff
PREFETCH window: 20000000-21ffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt Link [C0B8] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:02:06.0[A] -> Link [C0B8] -> GSI 11 (level, low) ->
IRQ 11
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1164408658.700:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
vesafb: framebuffer at 0x48000000, mapped to 0xd0880000, using 6144k, total
32768k
vesafb: mode is 1024x768x16, linelength=2048, pages=20
vesafb: protected mode interface info at c000:53db
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 47089
bytes,<6>...found (1024x768, 27542 bytes, v3).
Console: switching to colour frame buffer device 124x44
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
PNP: PS/2 Controller [PNP0303:C164,PNP0f13:C165] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS2 at I/O 0x3e8 (irq = 4) is a NS16550A
00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
ACPI: PCI Interrupt Link [C0B9] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [C0B9] -> GSI 10 (level, low) ->
IRQ 10
e100: eth0: e100_probe: addr 0x40100000, irq 10, MAC addr 00:08:02:B9:EA:BD
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
Synaptics Touchpad, model: 1, fw: 5.9, id: 0x336ab1, caps: 0x984793/0x0
serio: Synaptics pass-through port at isa0060/serio4/input0
input: SynPS/2 Synaptics TouchPad as /class/input/input1
input: PC Speaker as /class/input/input2
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 4, 65536 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
Using IPI Shortcut mode
swsusp: Resume From Partition /ev/hda7
PM: Checking swsusp image.
swsusp: Error -6 check for resume file
PM: Resume from disk failed.
ACPI wakeup devices:
C04D C09F C0A5 C0A8 C164 C165 C17A C120
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 148k freed
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH3M: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt Link [C0B7] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [C0B7] -> GSI 11 (level, low) ->
IRQ 11
ICH3M: chipset revision 2
ICH3M: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x4440-0x4447, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x4448-0x444f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: FUJITSU MHV2080AH, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=65535/16/63,
UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 >
Probing IDE interface ide1...
hdc: Compaq DVD-ROM GDR-8081N, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [C000] (supports 8 throttling states)
ACPI: Thermal Zone [TZ1] (41 C)
ACPI: Thermal Zone [TZ2] (47 C)
ACPI: Thermal Zone [TZ3] (27 C)
ACPI: Fan [C1D7] (off)
ACPI: Fan [C1D8] (off)
ACPI: Fan [C1D9] (off)
ACPI: Fan [C1DA] (off)
ACPI: Fan [C1E4] (off)
ACPI: Fan [C1E5] (off)
ACPI: Fan [C1E6] (off)
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
input: PS/2 Generic Mouse as /class/input/input3
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 1
[PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
lp0: using parport0 (interrupt-driven).
usbcore: registered new driver usbfs
hdc: ATAPI 24X DVD-ROM drive, 512kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
ieee1394: Initialized config rom entry `ip1394'
usbcore: registered new driver hub
ACPI: PCI Interrupt 0000:02:05.0[A] -> Link [C0B7] -> GSI 11 (level, low) ->
IRQ 11
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[40280000-402807ff]
Max Packet=[2048] IR/IT contexts=[4/8]
ACPI: PCI Interrupt 0000:02:0e.2[C] -> Link [C0B9] -> GSI 10 (level, low) ->
IRQ 10
ehci_hcd 0000:02:0e.2: EHCI Host Controller
ehci_hcd 0000:02:0e.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:02:0e.2: irq 10, io mem 0x40380000
ehci_hcd 0000:02:0e.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.16.23.snd-0.25-default ehci_hcd
usb usb1: SerialNumber: 0000:02:0e.2
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
ACPI: PCI Interrupt Link [C0B6] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [C0B6] -> GSI 5 (level, low) ->
IRQ 5
PCI: Setting latency timer of device 0000:00:1f.5 to 64
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Linux agpgart interface v0.101 (c) Dave Jones
intel8x0_measure_ac97_clock: measured 113386 usecs
intel8x0: clocking to 48000
ACPI: PCI Interrupt 0000:02:0e.0[A] -> Link [C0B9] -> GSI 10 (level, low) ->
IRQ 10
ohci_hcd 0000:02:0e.0: OHCI Host Controller
ohci_hcd 0000:02:0e.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:02:0e.0: irq 10, io mem 0x40180000
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.16.23.snd-0.25-default ohci_hcd
usb usb2: SerialNumber: 0000:02:0e.0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000802719cb9f14d]
i8xx TCO timer: initialized (0x1060). heartbeat=30 sec (nowayout=0)
ACPI: PCI Interrupt 0000:02:0e.1[B] -> Link [C0B9] -> GSI 10 (level, low) ->
IRQ 10
ohci_hcd 0000:02:0e.1: OHCI Host Controller
ohci_hcd 0000:02:0e.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:02:0e.1: irq 10, io mem 0x40200000
usb usb3: new device found, idVendor=0000, idProduct=0000
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: OHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.16.23.snd-0.25-default ohci_hcd
usb usb3: SerialNumber: 0000:02:0e.1
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 2-2: new low speed USB device using ohci_hcd and address 2
usb 2-2: new device found, idVendor=045e, idProduct=0039
usb 2-2: new device strings: Mfr=1, Product=3, SerialNumber=0
usb 2-2: Product: Microsoft 5-Button Mouse with IntelliEye(TM)
usb 2-2: Manufacturer: Microsoft
usb 2-2: configuration #1 chosen from 1 choice
ACPI: PCI Interrupt 0000:02:06.0[A] -> Link [C0B8] -> GSI 11 (level, low) ->
IRQ 11
Yenta: CardBus bridge found at 0000:02:06.0 [0e11:004e]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:06.0, mfunc 0x012c1202, devctl 0x64
agpgart: Detected an Intel i845 Chipset.
agpgart: AGP aperture is 256M @ 0x60000000
Yenta: ISA IRQ mask 0x0018, PCI irq 11
Socket status: 30000020
pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff
cs: IO port probe 0x2000-0x2fff: clean.
pcmcia: parent PCI bridge Memory window: 0x40000000 - 0x403fffff
pcmcia: parent PCI bridge Memory window: 0x20000000 - 0x21ffffff
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
usbcore: registered new driver hiddev
input: Microsoft Microsoft 5-Button Mouse with IntelliEye(TM) as
/class/input/input4
input: USB HID v1.10 Mouse [Microsoft Microsoft 5-Button Mouse with
IntelliEye(TM)] on usb-0000:02:0e.0-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
hw_random: RNG not detected
pccard: CardBus card inserted into slot 0
cs: IO port probe 0x100-0x4ff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xa00-0xaff: clean.
PCI: Enabling device 0000:03:00.0 (0080 -> 0082)
ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [C0B8] -> GSI 11 (level, low) ->
IRQ 11
pccard: card ejected from slot 0
ALSA sound/pci/rme9652/hdsp.c:771: Hammerfall-DSP: wait for FIFO status <= 0
failed after 30 iterations
ALSA sound/pci/rme9652/hdsp.c:4937: Hammerfall-DSP: couldn't get firmware
from userspace. try using hdsploader
ALSA sound/pci/rme9652/hdsp.c:4943: Hammerfall-DSP: card initialization
pending : waiting for firmware
pccard: CardBus card inserted into slot 0
PCI: Enabling device 0000:03:00.0 (0080 -> 0082)
ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [C0B8] -> GSI 11 (level, low) ->
IRQ 11
ALSA sound/pci/rme9652/hdsp.c:771: Hammerfall-DSP: wait for FIFO status <= 0
failed after 30 iterations
ALSA sound/pci/rme9652/hdsp.c:650: Hammerfall-DSP: loading firmware
ALSA sound/pci/rme9652/hdsp.c:683: Hammerfall-DSP: finished firmware loading
device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@xxxxxxxxxx
loop: loaded (max 8 devices)
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda10, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
AppArmor: AppArmor (version 2.0-19.43r6320) initialized
audit(1164408681.897:2): AppArmor (version 2.0-19.43r6320) initialized
Adding 746980k swap on /dev/hda7. Priority:-1 extents:1 across:746980k
ACPI: AC Adapter [C11B] (on-line)
ACPI: Battery Slot [C11E] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [C17A]
ACPI: Sleep Button (CM) [C120]
ACPI: Lid Switch [C11F]
audit(1164369091.567:3): audit_backlog_limit=256 old=64 by auid=4294967295
IA-32 Microcode Update Driver: v1.14 <tigran@xxxxxxxxxxx>
microcode: CPU0 updated from revision 0xd to 0x20, date = 06052003
IA-32 Microcode Update Driver v1.14 unregistered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
acpi-cpufreq: CPU0 - ACPI performance management activated.
ADDRCONF(NETDEV_UP): eth0: link is not ready
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
NET: Registered protocol family 17
bootsplash: status on console 0 changed to on
eth0: no IPv6 routers present
pccard: card ejected from slot 0
pccard: CardBus card inserted into slot 0
PCI: Enabling device 0000:03:00.0 (0080 -> 0082)
ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [C0B8] -> GSI 11 (level, low) ->
IRQ 11
ALSA sound/pci/rme9652/hdsp.c:4948: Hammerfall-DSP: Firmware already
present, initializing card.
smb_add_request: request [c57c0e80, mid=3591] timed out!
-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your
opinions on IT & business topics through brief surveys - and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV
_______________________________________________
Alsa-user mailing list
Alsa-user@xxxxxxxxxxxxxxxxxxxxx
https://lists.sourceforge.net/lists/listinfo/alsa-user
