Sami J. M?kinen wrote: > #22 Position A > #23 Option A > #26 Position B > #27 Option B > # port 1 option a position a > # port 2 option a position b > # port 3 option b position a > # port 4 option b position b > > The above applies to Biltema 4x1 switch > and to my current switch too. Don't remember > the name, though. Might have been Digiality or not. > > So in your setup I assume that you have ports and LNBs like this: > > 1 - S1.0W > 2 - S5.0E > 3 - S13.0E > 4 - not used > > This diseqc.conf should do the trick: > > # port 1 > S1.0W 11700 V 9750 t v W15 [E0 10 23] W15 [E0 10 22] W15 t > S1.0W 99999 V 10600 t v W15 [E0 10 23] W15 [E0 10 22] W15 T > S1.0W 11700 H 9750 t V W15 [E0 10 23] W15 [E0 10 22] W15 t > S1.0W 99999 H 10600 t V W15 [E0 10 23] W15 [E0 10 22] W15 T > > # port 2 > S5.0E 11700 V 9750 t v W15 [E0 10 23] W15 [E0 10 26] W15 t > S5.0E 99999 V 10600 t v W15 [E0 10 23] W15 [E0 10 26] W15 T > S5.0E 11700 H 9750 t V W15 [E0 10 23] W15 [E0 10 26] W15 t > S5.0E 99999 H 10600 t V W15 [E0 10 23] W15 [E0 10 26] W15 T > > # port 3 > S13.0E 11700 V 9750 t v W15 [E0 10 27] W15 [E0 10 22] W15 t > S13.0E 99999 V 10600 t v W15 [E0 10 27] W15 [E0 10 22] W15 T > S13.0E 11700 H 9750 t V W15 [E0 10 27] W15 [E0 10 22] W15 t > S13.0E 99999 H 10600 t V W15 [E0 10 27] W15 [E0 10 22] W15 T > > # port 4 > #Sxx.yE 11700 V 9750 t v W15 [E0 10 27] W15 [E0 10 26] W15 t > #Sxx.yE 99999 V 10600 t v W15 [E0 10 27] W15 [E0 10 26] W15 T > #Sxx.yE 11700 H 9750 t V W15 [E0 10 27] W15 [E0 10 26] W15 t > #Sxx.yE 99999 H 10600 t V W15 [E0 10 27] W15 [E0 10 26] W15 T > > If the order of ports is different, just edit that. > Not that difficult, is it? Just read the diseqc pdf spec. :) > > -sjm > > > _______________________________________________ > vdr mailing list > vdr@xxxxxxxxxxx > http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr > Very well written and interesting data you got there. But I don't just get it why even this doesn't work, though you mentioned that it works with the biltema stuff as both of mine are of those. Same thing still occurs with both switches, to watch channels with V-pol I first must switch to a H-pol channel. Could this somehow be a limitation of the Skystar 2-pci card? Then again, best configuration that actually has worked flawlesly so far with these twin-lnb's is the configuration for a mini-diseqc with A and B commands, but then I'm without the 3rd satellite. Veeery confusing. I'm off to work now, so I can't continue testing and exploring until tomorrow again. Thanks for your replies guys, HH
