Hi Sascha,
> On March 5, 2020 at 2:24 PM Sascha Hauer <s.hauer@xxxxxxxxxxxxxx> wrote:
>
>
> On Thu, Mar 05, 2020 at 10:50:15AM +0100, Giorgio Dal Molin wrote:
> > Hi,
> >
> > thank you for the quick reply.
> >
> > here is how I register the bbu for the spi flash:
> >
> > imx7_bbu_internal_spi_i2c_register_handler("SPI", "/dev/m25p0", BBU_HANDLER_FLAG_DEFAULT);
> >
> > and here is a hex dump of the spi flash after bb-updating (I hacked the 'cat' command a bit):
> >
> > imx7d: / cat -h -b 0x450 /dev/m25p0
>
> There's the 'md' command for this purpose ;)
>
> > 0000: 0xfe 0x03 0x00 0xea 0xfe 0xff 0xff 0xea 0xfe 0xff 0xff 0xea 0xfe 0xff 0xff 0xea
> > 0010: 0xfe 0xff 0xff 0xea 0xfe 0xff 0xff 0xea 0xfe 0xff 0xff 0xea 0xfe 0xff 0xff 0xea
> > 0020: 0x62 0x61 0x72 0x65 0x62 0x6f 0x78 0x00 0x00 0x00 0x00 0x00 0x00 0xf0 0x06 0x00
> > 0030: 0x55 0x55 0x55 0x55 0x55 0x55 0x55 0x55 0x55 0x55 0x55 0x55 0x55 0x55 0x55 0x55
> > 0040: 0x55 0x55 0x55 0x55 0x55 0x55 0x55 0x55 0x55 0x55 0x55 0x55 0x55 0x55 0x55 0x55
> > 0050: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
> > ... < zeros > ...
> > 03f0: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
> > 0400: 0xd1 0x00 0x20 0x40 0x00 0x10 0x00 0x80 0x00 0x00 0x00 0x00 0x2c 0x04 0x00 0x80
> > 0410: 0x20 0x04 0x00 0x80 0x00 0x04 0x00 0x80 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
> > 0420: 0x00 0x00 0x00 0x80 0x00 0xf0 0x06 0x00 0x00 0x00 0x00 0x00 0xd2 0x01 0xbc 0x40
> > 0430: 0xcc 0x01 0x6c 0x04 0x30 0x34 0x00 0x04 0x0f 0x40 0x00 0x05 0x30 0x39 0x10 0x00
> > 0440: 0x00 0x00 0x00 0x02 0x30 0x7a 0x00 0x00 0x01 0x04 0x00 0x01 0x30 0x7a 0x01 0xa0
> >
> > It seems 'reasonable': there's a 0x400 bytes flash header and then the actual image
> > starts, but it does not boot.
>
> ...
>
> > 03f0: 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
> > 0400: 0xd1 0x00 0x20 0x40 0x00 0x10 0x91 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
> > 0410: 0x20 0x04 0x91 0x00 0x00 0x04 0x91 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
> > 0420: 0x00 0x00 0x91 0x00 0x00 0xa0 0x00 0x00 0x00 0x00 0x00 0x00 0xd2 0x00 0x04 0x40
> > 0430: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
> > 0440: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
> >
> >
> > The first 4 bites at offset 0x400 are the same but then the u-boot working image is
> > different.
>
> Where do you have the SDRAM setup? The U-Boot snippet loads into
> internal SRAM which looks like the SDRAM setup is done in code. The
> barebox image above loads into SDRAM which of course requires that you
> have setup the SDRAM in the DCD table.
>
Yes, this is right, u-boot does not have a DCD, they init the soc (ddr cntr)
in the bootloader self.
The DCD I use in barebox works when I upload the image with the imx-usb-loader:
root [ /tmp ]# /tmp/bbuild/arm32/scripts/imx/imx-usb-loader /tmp/bbuild/arm32/barebox-flash-image
found i.MX7S USB device [15a2:0076]
main dcd length 1bc
DCD write: sub dcd length: 0x016c, flags: 0x04
DCD check condition 3 on address 0x307900c4
DCD write: sub dcd length: 0x0034, flags: 0x04
DCD check condition 3 on address 0x307a0004
loading binary file(/tmp/bbuild/arm32/barebox-flash-image) to 0x80000000, skip=0x0, fsize=456157 type=170...
binary file successfully loaded
jumping to 0x80000400
The same barebox image on the spi flash does not work; unfortunately I have no debug
messages in that case, I just see that the u-boot image boots so the HW is OK.
giorgio
> Sascha
>
> --
> Pengutronix e.K. | |
> Steuerwalder Str. 21 | http://www.pengutronix.de/ |
> 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
>
> _______________________________________________
> barebox mailing list
> barebox@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/barebox
_______________________________________________
barebox mailing list
barebox@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/barebox
