[PATCH 2/3] mxs: iomux-imx23/imx28: unify mode definition

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



i.MX23 and i.MX28 iomux mode definitions differ for no good reason.

Compared to the two previous definitions this introduces a few flags
that are not used yet but this changes in the next commit to detect
broken definitions.

Apart from different constants this commit intends to be a no-op. If
there are changes in the register values there is either a bug in this
patch or the used mode is broken (e.g. a pullup value is defined for a
pin that has a bitkeeper).

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@xxxxxxxxxxxxxx>
---
 arch/arm/mach-mxs/include/mach/iomux-imx23.h | 61 ---------------------
 arch/arm/mach-mxs/include/mach/iomux-imx28.h | 60 --------------------
 arch/arm/mach-mxs/include/mach/iomux.h       | 82 ++++++++++++++++++++++++++++
 3 files changed, 82 insertions(+), 121 deletions(-)

diff --git a/arch/arm/mach-mxs/include/mach/iomux-imx23.h b/arch/arm/mach-mxs/include/mach/iomux-imx23.h
index 39d69810ef08..1e225f8fc51b 100644
--- a/arch/arm/mach-mxs/include/mach/iomux-imx23.h
+++ b/arch/arm/mach-mxs/include/mach/iomux-imx23.h
@@ -9,72 +9,11 @@
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
- *
  */
 
-/* 3322222222221111111111
- * 10987654321098765432109876543210
- *                              ^^^_ Register Number
- *                          ^^^^____ Bit offset
- *                        ^^________ Function
- *                       ^__________ Drive strength feature present
- *                      ^___________ Pull up present
- *                    ^^____________ Drive strength setting
- *                   ^______________ Pull up / bit keeper setting
- *                  ^_______________ Voltage select present
- *                 ^________________ Voltage selection
- *             ^____________________ direction if enabled as GPIO (1 = output)
- *            ^_____________________ initial output value if enabled as GPIO and configured as output
- *           ^______________________ Bit keeper present
- */
 #ifndef __ASM_MACH_IOMUX_MX23_H
 #define __ASM_MACH_IOMUX_MX23_H
 
-/* control pad's function */
-#define FBIT_SHIFT (3)
-#define PORTF(bank,bit)	(((bit) << FBIT_SHIFT) | (bank))
-#define GET_PORTF(x) ((x) & 0x7)
-#define GET_FBITPOS(x) (((x) >> FBIT_SHIFT) & 0xf)
-#define GET_GPIO_NO(x) ((GET_PORTF(x) << 4) + GET_FBITPOS(m))
-#define FUNC_SHIFT 7
-#define FUNC(x)	((x) << FUNC_SHIFT)
-#define GET_FUNC(x) (((x) >> FUNC_SHIFT) & 3)
-#define IS_GPIO (3)
-
-/* control pad's GPIO feature if enabled */
-#define GPIO_OUT (1 << 19)
-#define GPIO_VALUE(x) ((x) << 20)
-#define GPIO_IN (0 << 19)
-#define GET_GPIODIR(x) (!!((x) & (1 << 19)))
-#define GET_GPIOVAL(x) (!!((x) & (1 << 20)))
-
-/* control pad's drive strength */
-#define SE (1 << 9)
-#define SE_PRESENT(x) (!!((x) & SE))
-#define STRENGTH(x) ((x) << 11)
-#define S4MA 0	/* used to define a 4 mA drive strength */
-#define S8MA 1	/* used to define a 8 mA drive strength */
-#define S12MA 2	/* used to define a 12 mA drive strength */
-#define S16MA 3	/* used to define a 16 mA drive strength, not all pads can drive this current! */
-#define GET_STRENGTH(x) (((x) >> 11) & 0x3)
-
-/* control pad's pull up / bit keeper feature */
-#define PE (1 << 10)
-#define BK (1 << 21)
-#define PE_PRESENT(x) (!!((x) & PE))
-#define BK_PRESENT(x) (!!((x) & BK))
-#define PULLUP(x) ((x) << 13)
-#define BITKEEPER(x) ((x) << 14)
-#define GET_PULLUP(x) (!!((x) & (1 << 13)))
-#define GET_BITKEEPER(x) (!!((x) & BITKEEPER(1)))
-
-/* control pad's voltage feature */
-#define VE (1 << 14)
-#define VE_PRESENT(x) (!!((x) & VE))
-#define VE_1_8V (0 << 15)
-#define VE_2_5V (0 << 15) /* don't ask my why, RTFM */
-#define GET_VOLTAGE(x) (!!((x) & (1 << 15)))
-
 /* Bank 0, pins 0 ... 15, GPIO pins 0 ... 15 */
 #define GPMI_D15		(FUNC(0) | PORTF(0, 15) | SE | PE)
 #define GPMI_D15_AUART2_TX	(FUNC(1) | PORTF(0, 15) | SE | PE)
diff --git a/arch/arm/mach-mxs/include/mach/iomux-imx28.h b/arch/arm/mach-mxs/include/mach/iomux-imx28.h
index c9ab8a93aea2..6119f3caf98d 100644
--- a/arch/arm/mach-mxs/include/mach/iomux-imx28.h
+++ b/arch/arm/mach-mxs/include/mach/iomux-imx28.h
@@ -10,69 +10,9 @@
  * GNU General Public License for more details.
  */
 
-/* 3322222222221111111111
- * 10987654321098765432109876543210
- *                            ^^^^^_ Bit offset
- *                         ^^^______ Register Number
- *                       ^^_________ Function
- *                      ^___________ Drive strength feature present
- *                     ^____________ Pull up present
- *                   ^^_____________ Drive strength setting
- *                  ^_______________ Pull up / bit keeper setting
- *                 ^________________ Voltage select present
- *                ^_________________ Voltage selection
- *            ^_____________________ direction if enabled as GPIO (1 = output)
- *           ^______________________ initial output value if enabled as GPIO
- *                                   and configured as output
- *          ^_______________________ Bit keeper present
- */
 #ifndef __MACH_IOMUX_IMX28_H
 #define __MACH_IOMUX_IMX28_H
 
-/* control pad's function */
-#define FBANK_SHIFT (5)
-#define PORTF(bank,bit)	(((bank) << FBANK_SHIFT) | (bit))
-#define GET_GPIO_NO(x) ((x) & 0xff)
-#define FUNC_SHIFT 8
-#define FUNC(x)	((x) << FUNC_SHIFT)
-#define GET_FUNC(x) (((x) >> FUNC_SHIFT) & 3)
-#define IS_GPIO (3)
-
-/* control pad's GPIO feature if enabled */
-#define GPIO_OUT (1 << 20)
-#define GPIO_VALUE(x) ((x) << 21)
-#define GPIO_IN (0 << 20)
-#define GET_GPIODIR(x) (!!((x) & (1 << 20)))
-#define GET_GPIOVAL(x) (!!((x) & (1 << 21)))
-
-/* control pad's drive strength */
-#define SE (1 << 10)
-#define SE_PRESENT(x) (!!((x) & SE))
-#define STRENGTH(x) ((x) << 12)
-#define S4MA 0	/* used to define a 4 mA drive strength */
-#define S8MA 1	/* used to define a 8 mA drive strength */
-#define S12MA 2	/* used to define a 12 mA drive strength */
-#define S16MA 3	/* used to define a 16 mA drive strength,
-		   not all pads can drive this current! */
-#define GET_STRENGTH(x) (((x) >> 12) & 0x3)
-
-/* control pad's pull up / bit keeper feature */
-#define PE (1 << 11)
-#define BK (1 << 22)
-#define PE_PRESENT(x) (!!((x) & PE))
-#define BK_PRESENT(x) (!!((x) & BK))
-#define PULLUP(x) ((x) << 14)
-#define BITKEEPER(x) ((x) << 14)
-#define GET_PULLUP(x) (!!((x) & PULLUP(1)))
-#define GET_BITKEEPER(x) (!!((x) & BITKEEPER(1)))
-
-/* control pad's voltage feature */
-#define VE (1 << 15)
-#define VE_PRESENT(x) (!!((x) & VE))
-#define VE_1_8V (0 << 16)
-#define VE_3_3V (1 << 16)
-#define GET_VOLTAGE(x) (!!((x) & (1 << 16)))
-
 /* Bank 0, GPIO pins 0 ... 31 */
 #define GPMI_RESETN		(FUNC(0) | PORTF(0, 28) | SE | VE | PE)
 #define GPMI_RESETN_SSP3_CMD	(FUNC(1) | PORTF(0, 28) | SE | VE | PE)
diff --git a/arch/arm/mach-mxs/include/mach/iomux.h b/arch/arm/mach-mxs/include/mach/iomux.h
index 84496c6b8497..a647439303fc 100644
--- a/arch/arm/mach-mxs/include/mach/iomux.h
+++ b/arch/arm/mach-mxs/include/mach/iomux.h
@@ -18,10 +18,92 @@
 
 #include <types.h>
 
+/*
+ * The muxable pins on i.MX23 are organized in 4 banks. On i.MX28 there are 7
+ * banks. Each bank has up to 32 pins each. Furthermore for each pin some of the
+ * following properties can be configured:
+ *  - drive strength: 4 mA, 8 mA, 12 mA or 16 mA
+ *  - pull up enabled or bit keeper enabled (a pin cannot have both)
+ *  - voltage: 1.8 V, 2.5 V (i.MX23 only) or 3.3 V (i.MX28 only)
+ *  - function: 0..3, with 3 being the GPIO functionality
+ *
+ * So a configuration for a given pin can be described in an unsigned integer of
+ * length 32:
+ *  - [ 4: 0] bank pin
+ *  - [ 7: 5] bank
+ *  - [    8] 1 iff pin has a switchable pull up
+ *  - [    9] 1 iff pin has a switchable bit keeper
+ *  - [   10] 1 iff pin has switchable drive strength
+ *  - [   11] 1 iff pin has switchable voltage
+ *  - [13:12] function
+ *  - [   14] 1 for enabled pull up
+ *  - [   15] 1 iff [14] is a valid pull up value
+ *  - [   16] 1 for enabled bit keeper
+ *  - [   17] 1 iff [16] is a valid bit keeper value
+ *  - [19:18] value for drive strength i -> i * 4 mA
+ *  - [   20] 1 iff [19:18] is valid
+ *  - [   21] 0 for 1.8 V, 1 for 2.5 V resp. 3.3 V
+ *  - [   22] 1 iff [21] is valid
+ *  - [   23] 1 iff configure as GPIO out if function == 3 (i.e. GPIO)
+ *  - [   24] initial value iff configured as GPIO out
+ *  - [   25] error
+ */
+
+#define BANKPIN(p)	(((p) & 31) | ERROR((p) & ~31))
+#define BANK(b)		((((b) & 7) << 5) | (ERROR((b) & ~7)))
+#define PE		(1 << 8)
+#define BK		(1 << 9)
+#define SE		(1 << 10)
+#define VE		(1 << 11)
+#define FUNC(f)		((((f) & 3) << 12) | (ERROR((f) & ~3)))
+#define PULLUP(p)	((((p) & 1) << 14) | PEVALID | ERROR((p) & ~1))
+#define PEVALID		(1 << 15)
+#define BITKEEPER(b)	((((b) & 1) << 16) | BKVALID | ERROR((b) & ~1))
+#define BKVALID		(1 << 17)
+#define STRENGTH(s)	((((s) & 3) << 18) | SEVALID | ERROR((s) & ~3))
+#define S4MA		0
+#define S8MA		1
+#define S12MA		2
+#define S16MA		3
+#define SEVALID		(1 << 20)
+#define VOLTAGE(v)	((((v) & 1) << 21) | VEVALID | ERROR((v) & ~1))
+#define VE_1_8V		VOLTAGE(0)
+#define VEVALID		(1 << 22)
+
+#define GPIO_OUT	(1 << 23)
+#define GPIO_IN		(0 << 23)
+#define GPIO_VALUE(v)	((((v) & 1) << 24) | ERROR((v) & ~1))
+
+#define ERROR(x)	(!!(x) << 25)
+
+#define GET_GPIO_NO(m)	((m) & 0xff)
+#define GET_FUNC(m)	(((m) >> 12) & 3)
+#define PE_PRESENT(m)	((m) & PE)
+#define GET_PULLUP(m)	(((m) >> 14) & 1)
+#define BK_PRESENT(m)	((m) & BK)
+#define GET_BITKEEPER(m)(((m) >> 16) & 1)
+#define SE_PRESENT(m)	((m) & SE)
+#define GET_STRENGTH(m)	(((m) >> 18) & 3)
+#define VE_PRESENT(m)	((m) & VE)
+#define GET_VOLTAGE(m)	(((m) >> 21) & 1)
+#define GET_GPIODIR(m)	(!!((m) & GPIO_OUT))
+#define GET_GPIOVAL(m)	(!!((m) & GPIO_VALUE(1)))
+#define IS_GPIO		3
+
 #if defined CONFIG_ARCH_IMX23
+/*
+ * The pin definition of i.MX23 are strange. Bank 0's pins 0 .. 15 are defined
+ * using PORTF(0, 0) .. PORTF(0, 15). Its pins 16 .. 31 however use PORTF(1, 0)
+ * .. PORTF(1, 15). So the PORTF macro is more ugly than necessary.
+ */
+# define PORTF(bank,bit)	(BANK((bank) / 2) | BANKPIN((((bank) & 1) << 4) | (bit)) | ERROR((bit) & ~15) | ERROR((bank) & ~7)
+# define VE_2_5V		VOLTAGE(1)
 # include <mach/iomux-imx23.h>
 #endif
+
 #if defined CONFIG_ARCH_IMX28
+# define PORTF(bank,bit)	(BANK(bank) | BANKPIN(bit))
+# define VE_3_3V	VOLTAGE(1)
 # include <mach/iomux-imx28.h>
 #endif
 
-- 
2.1.1


_______________________________________________
barebox mailing list
barebox@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/barebox





[Index of Archives]     [Linux Embedded]     [Linux USB Devel]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]

  Powered by Linux