Понедельник, 12 августа 2013, 9:07 +02:00 от Sascha Hauer <s.hauer@xxxxxxxxxxxxxx>: > On Sat, Aug 10, 2013 at 08:10:53AM +0400, Alexander Shiyan wrote: > > Hello. > > > > USB functionality on PCM038 (PCM970) is broken again due > > patch "Revert usb: chipidea-imx: Fix usb initialization". > > > > Board: Phytec phyCORE-i.MX27 > > detected i.MX27 revision 2.1 > > netconsole: registered as cs1 > > mc13xxx-spi mc137830: Found MC13783 ID: 0x00009b [Rev: 3.1] > > cfi_flash cfi_flash0: found cfi flash at c0000000, size 33554432 > > nand: NAND device: Manufacturer ID: 0x20, Chip ID: 0x36 (ST Micro NAND 64MiB 1,8V 8-bit), 64MiB, page size: 512, OOB size: 16 > > Bad block table found at page 131040, version 0x01 > > Bad block table found at page 131008, version 0x01 > > imxfb imxfb: i.MX Framebuffer driver > > mdio_bus: miibus0: probed > > No ULPI found. vid: 0x0000 pid: 0x0000 > > pcm038: Using environment in NOR Flash > > No ULPI found. vid: 0x0000 pid: 0x0000 > > imx-usb imx-usb2: USB EHCI 1.00 > > imx-mmc imx-mmc1: registered as imx-mmc1 > > running /env/bin/init... > > > > After remove this patch, all works fine. > > Have you verified it really doesn't work? I get the 'No ULPI found' > message aswell, but the ULPI phys are probed again during the 'usb' > command and it then works here. Same result on CCMX51. barebox 2013.06.0-00186-gae970c3 #12 Tue Jul 2 13:56:48 MSK 2013 Board: ConnectCore i.MX51 detected i.MX51 revision 3.0 Module Variant: i.MX515@600MHz, PHY, Accel (0x0b) Module HW Rev : 03 Module Serial : B111156789 mc13xxx-spi mc13xxx-spi0: Found MC13892 ID: 0x0045d0 [Rev: 2.0a] nand: ONFI param page 0 valid nand: ONFI flash detected ... nand: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08AAD), page size: 2048, OOB size: 64 malloc space: 0x95f00000 -> 0x97efffff (size 32 MiB) imx-esdhc imx-esdhc0: registered as imx-esdhc0 Found NXP ISP150x ULPI transceiver (0x04cc:0x1504). imx-usb imx-usb1: USB EHCI 1.00 envfs: wrong magic on /dev/env0 no valid environment found on /dev/env0. Using default environment running /env/bin/init... ... barebox 2013.08.0-00157-g9b0907b-dirty #3 Mon Aug 12 14:47:06 MSK 2013 Board: ConnectCore i.MX51 detected i.MX51 revision 3.0 Module Variant: i.MX515@600MHz, PHY, Accel (0x0b) Module HW Rev : 03 Module Serial : B111156789 mc13xxx-spi mc138920: Found MC13892 ID: 0x0045d0 [Rev: 2.0a] nand: ONFI param page 0 valid nand: ONFI flash detected nand: NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08AAD), 256MiB, page size: 2048, OOB size: 64 Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 malloc space: 0x95f00000 -> 0x97efffff (size 32 MiB) imx-esdhc imx-esdhc0: registered as imx-esdhc0 No ULPI found. vid: 0x0000 pid: 0x0000 imx-usb imx-usb1: USB EHCI 1.00 envfs: wrong magic on /dev/env0 no valid environment found on /dev/env0. Using default environment running /env/bin/init... ... And yes, this works after "usb" command: barebox@ConnectCore i.MX51:/ usb USB: scanning bus for devices... Found NXP ISP150x ULPI transceiver (0x04cc:0x1504). Bus 001 Device 001: ID 0000:0000 EHCI Host Controller 1 USB Device(s) found So, you consider this is not a bug? --- _______________________________________________ barebox mailing list barebox@xxxxxxxxxxxxxxxxxxx http://lists.infradead.org/mailman/listinfo/barebox
