Hi Geert-san, > From: Geert Uytterhoeven > Sent: Monday, April 25, 2016 3:58 PM > > Hi Shimoda-san, > > On Mon, Apr 25, 2016 at 4:10 AM, Yoshihiro Shimoda > <yoshihiro.shimoda.uh@xxxxxxxxxxx> wrote: > >> From: Rob Herring > >> Sent: Friday, April 22, 2016 10:29 PM > >> On Fri, Apr 22, 2016 at 4:36 AM, Felipe Balbi > >> <felipe.balbi@xxxxxxxxxxxxxxx> wrote: > >> > Yoshihiro Shimoda <yoshihiro.shimoda.uh@xxxxxxxxxxx> writes: > >> >> The firmware of R-Car USB 3.0 host controller will control the reset. > >> >> So, if the xhci driver doesn't do firmware downloading (e.g. kernel > >> >> configuration is CONFIG_USB_XHCI_PLATFORM=y and CONFIG_USB_XHCI_RCAR > >> >> is not set), the reset of USB 3.0 host controller doesn't work > >> >> correctly. Then, the host controller will cause long wait in > >> >> xhci_reset() because the CMD_RESET bit of op_regs->command is not > >> >> cleared for 10 seconds. > >> >> > >> >> So, this patch modifies the xhci_rcar_init_quirk() in xhci-rcar.h > >> >> to exit the probe function immediately. > >> >> > >> >> Fixes: 4ac8918f3a7 (usb: host: xhci-plat: add support for the R-Car H2 and M2 xHCI controllers) > >> >> Cc: <stable@xxxxxxxxxxxxxxx> # v3.17+ > >> >> Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@xxxxxxxxxxx> > >> >> --- > >> >> Changes from v1: > >> >> - Revise the commit log. > >> >> (http://www.spinics.net/lists/stable/msg130007.html) > >> >> > >> >> drivers/usb/host/xhci-rcar.h | 6 +++++- > >> >> 1 file changed, 5 insertions(+), 1 deletion(-) > >> >> > >> >> diff --git a/drivers/usb/host/xhci-rcar.h b/drivers/usb/host/xhci-rcar.h > >> >> index 2941a25..2afed68 100644 > >> >> --- a/drivers/usb/host/xhci-rcar.h > >> >> +++ b/drivers/usb/host/xhci-rcar.h > >> >> @@ -24,7 +24,11 @@ static inline void xhci_rcar_start(struct usb_hcd *hcd) > >> >> > >> >> static inline int xhci_rcar_init_quirk(struct usb_hcd *hcd) > >> >> { > >> >> - return 0; > >> >> + /* > >> >> + * To avoid wait and timeout in xhci_reset() if CONFIG_XHCI_RCAR is > >> >> + * disabled, this function fails. > >> >> + */ > >> >> + return -ENODEV; > >> > > >> > okay, if I understood correctly the thing is that you have a kernel > >> > built with XHCI platform support but without XHCI RCAR support. Then, if > >> > you run this kernel on RCAR board, you see this CMD_RESET problem, > >> > right? > > [...] > > >> We should fix this in kconfig to always enable the option when RCAR is > >> enabled IMO. > > > > I could fix this in kconfig like the followings: > > > > diff --git a/arch/arm/mach-shmobile/Kconfig b/arch/arm/mach-shmobile/Kconfig > > index f2bc5c3..905d1d2 100644 > > --- a/arch/arm/mach-shmobile/Kconfig > > +++ b/arch/arm/mach-shmobile/Kconfig > > @@ -46,6 +46,7 @@ menuconfig ARCH_RENESAS > > select PINCTRL > > select ARCH_REQUIRE_GPIOLIB > > select ZONE_DMA if ARM_LPAE > > + select USB_XHCI_RCAR if USB_XHCI_HCD > > > > if ARCH_RENESAS > > > > diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms > > index efa77c1..010d2b7 100644 > > --- a/arch/arm64/Kconfig.platforms > > +++ b/arch/arm64/Kconfig.platforms > > @@ -105,6 +105,7 @@ config ARCH_RENESAS > > select PM > > select PM_GENERIC_DOMAINS > > select RENESAS_IRQC > > + select USB_XHCI_RCAR if USB_XHCI_HCD > > help > > This enables support for the ARMv8 based Renesas SoCs. > > > > If this is acceptable, I will send each patch to arm / arm64. > > What about enforcing this in a single place instead, i.e. in > drivers/usb/host/Kconfig? Thank you for the suggestion. I could make such a patch. I prefer this than each arm / arm64 patch. diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig index 3050b18..e9d4dde 100644 --- a/drivers/usb/host/Kconfig +++ b/drivers/usb/host/Kconfig @@ -35,6 +35,7 @@ config USB_XHCI_PCI config USB_XHCI_PLATFORM tristate "Generic xHCI driver for a platform device" + select USB_XHCI_RCAR if ARCH_RENESAS ---help--- Adds an xHCI host driver for a generic platform device, which provides a memory space and an irq. @@ -63,7 +64,7 @@ config USB_XHCI_MVEBU config USB_XHCI_RCAR tristate "xHCI support for Renesas R-Car SoCs" - select USB_XHCI_PLATFORM + depends on USB_XHCI_PLATFORM depends on ARCH_RENESAS || COMPILE_TEST ---help--- Say 'Y' to enable the support for the xHCI host controller Best regards, Yoshihiro Shimoda > Gr{oetje,eeting}s, > > Geert > > -- > Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx > > In personal conversations with technical people, I call myself a hacker. But > when I'm talking to journalists I just say "programmer" or something like that. > -- Linus Torvalds ��.n��������+%������w��{.n�����������ܨ}���Ơz�j:+v�����w����ޙ��&�)ߡ�a����z�ޗ���ݢj��w�f