Hi Shimoda-san, On Mon, Apr 25, 2016 at 4:10 AM, Yoshihiro Shimoda <yoshihiro.shimoda.uh@xxxxxxxxxxx> wrote: >> From: Rob Herring >> Sent: Friday, April 22, 2016 10:29 PM >> On Fri, Apr 22, 2016 at 4:36 AM, Felipe Balbi >> <felipe.balbi@xxxxxxxxxxxxxxx> wrote: >> > Yoshihiro Shimoda <yoshihiro.shimoda.uh@xxxxxxxxxxx> writes: >> >> The firmware of R-Car USB 3.0 host controller will control the reset. >> >> So, if the xhci driver doesn't do firmware downloading (e.g. kernel >> >> configuration is CONFIG_USB_XHCI_PLATFORM=y and CONFIG_USB_XHCI_RCAR >> >> is not set), the reset of USB 3.0 host controller doesn't work >> >> correctly. Then, the host controller will cause long wait in >> >> xhci_reset() because the CMD_RESET bit of op_regs->command is not >> >> cleared for 10 seconds. >> >> >> >> So, this patch modifies the xhci_rcar_init_quirk() in xhci-rcar.h >> >> to exit the probe function immediately. >> >> >> >> Fixes: 4ac8918f3a7 (usb: host: xhci-plat: add support for the R-Car H2 and M2 xHCI controllers) >> >> Cc: <stable@xxxxxxxxxxxxxxx> # v3.17+ >> >> Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@xxxxxxxxxxx> >> >> --- >> >> Changes from v1: >> >> - Revise the commit log. >> >> (http://www.spinics.net/lists/stable/msg130007.html) >> >> >> >> drivers/usb/host/xhci-rcar.h | 6 +++++- >> >> 1 file changed, 5 insertions(+), 1 deletion(-) >> >> >> >> diff --git a/drivers/usb/host/xhci-rcar.h b/drivers/usb/host/xhci-rcar.h >> >> index 2941a25..2afed68 100644 >> >> --- a/drivers/usb/host/xhci-rcar.h >> >> +++ b/drivers/usb/host/xhci-rcar.h >> >> @@ -24,7 +24,11 @@ static inline void xhci_rcar_start(struct usb_hcd *hcd) >> >> >> >> static inline int xhci_rcar_init_quirk(struct usb_hcd *hcd) >> >> { >> >> - return 0; >> >> + /* >> >> + * To avoid wait and timeout in xhci_reset() if CONFIG_XHCI_RCAR is >> >> + * disabled, this function fails. >> >> + */ >> >> + return -ENODEV; >> > >> > okay, if I understood correctly the thing is that you have a kernel >> > built with XHCI platform support but without XHCI RCAR support. Then, if >> > you run this kernel on RCAR board, you see this CMD_RESET problem, >> > right? [...] >> We should fix this in kconfig to always enable the option when RCAR is >> enabled IMO. > > I could fix this in kconfig like the followings: > > diff --git a/arch/arm/mach-shmobile/Kconfig b/arch/arm/mach-shmobile/Kconfig > index f2bc5c3..905d1d2 100644 > --- a/arch/arm/mach-shmobile/Kconfig > +++ b/arch/arm/mach-shmobile/Kconfig > @@ -46,6 +46,7 @@ menuconfig ARCH_RENESAS > select PINCTRL > select ARCH_REQUIRE_GPIOLIB > select ZONE_DMA if ARM_LPAE > + select USB_XHCI_RCAR if USB_XHCI_HCD > > if ARCH_RENESAS > > diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms > index efa77c1..010d2b7 100644 > --- a/arch/arm64/Kconfig.platforms > +++ b/arch/arm64/Kconfig.platforms > @@ -105,6 +105,7 @@ config ARCH_RENESAS > select PM > select PM_GENERIC_DOMAINS > select RENESAS_IRQC > + select USB_XHCI_RCAR if USB_XHCI_HCD > help > This enables support for the ARMv8 based Renesas SoCs. > > If this is acceptable, I will send each patch to arm / arm64. What about enforcing this in a single place instead, i.e. in drivers/usb/host/Kconfig? Gr{oetje,eeting}s, Geert -- Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that. -- Linus Torvalds -- To unsubscribe from this list: send the line "unsubscribe stable" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html