I use two ports in Micortik Router. one for WAN and other for LAN, I have No rules setup in Router except the natting Src and Dst for private to public IP and vice versa. There are two nics in squid box. but I am using only one. The Lan From router is Connected to switch and the squid nic is also connected to the same vlan of the switch. and i'm using a box connected to the the same vlan of the switch to test squid. Simple . Router to Switch Squid to Switch Test to Switch All in the same Vlan. Thanks, Ganesh J On Thu, Jul 10, 2014 at 6:04 AM, Nyamul Hassan <nyamul@xxxxxxxxx> wrote: > What are the rules in Mikrotik that you are using? What is the > network diagram? How many interfaces on Mikrotik are you using for > this purpose? How many NICs are there on the Squid box? Can you give > an idea of your network diagram? > > Also, a few days ago, I also posted the rules that I am using in > Mikrotik. Can you check if they match yours? > > Regards > HASSAN > > On Thu, Jul 10, 2014 at 6:28 AM, Info OoDoO <info@xxxxxxxxxxx> wrote: >> Hi, >> I'm using Microtik 1100 AH X2 Router, >> >> here is my Basic Data from your latest script. >> >> http://pastebin.com/GHkD5yYx >> >> Thanks, >> Ganesh J >> >> >> On Wed, Jul 9, 2014 at 1:08 AM, Eliezer Croitoru <eliezer@xxxxxxxxxxxx> wrote: >>> What router are you using?? >>> >>> Eliezer >>> >>> P.S. I will be at the squid irc channel for about couple hours >>> http://webchat.freenode.net/?channels=squid >>> >>> >>> On 07/08/2014 10:19 PM, Info OoDoO wrote: >>>> >>>> Configured Squid 3.4.6 again with all the options, still facing the same >>>> issue. >>>> >>>> Thanks, >>>> Ganesh J >>>> >>>> >>>> On Tue, Jul 8, 2014 at 11:55 PM, Nyamul Hassan <nyamul@xxxxxxxxx> wrote: >>>>> >>>>> We were in the same problem just a few days ago. Can you recompile and >>>>> check? >>>>> >>>>> Also, since you are compiling, then can you also try the latest stable >>>>> version 3.4.6? >>>>> >>>>> Regards >>>>> HASSAN >>>>> >>>>> >>>>> On Wed, Jul 9, 2014 at 12:24 AM, Info OoDoO <info@xxxxxxxxxxx> wrote: >>>>>> >>>>>> Sorry, I installed it recently and it was not there when i compiled >>>>>> and configured squid from source. >>>>>> >>>>>> Thanks, >>>>>> Ganesh J >>>>>> >>>>>> >>>>>> On Tue, Jul 8, 2014 at 11:52 PM, Info OoDoO <info@xxxxxxxxxxx> wrote: >>>>>>> >>>>>>> Yes.. it is installed.. >>>>>>> >>>>>>> libcap-devel.x86_64 2.16-5.5.el6 @base >>>>>>> >>>>>>> Thanks, >>>>>>> Ganesh J >>>>>>> >>>>>>> >>>>>>> On Tue, Jul 8, 2014 at 11:49 PM, Nyamul Hassan <nyamul@xxxxxxxxx> >>>>>>> wrote: >>>>>>>>>> >>>>>>>>>> For your kind attention, i have not installed Squid 3.1.10 from YUM. >>>>>>>>>> I >>>>>>>>>> have Compiled and installed from the source with the following >>>>>>>>>> options. >>>>>>>>>> >>>>>>>>>> http://pastebin.com/jFhzd3qj >>>>>>>>>> >>>>>>>> >>>>>>>> Oh! If you did compile it, then can you check if you have >>>>>>>> "libcap-devel" installed? >>>>>>>> >>>>>>>> Regards >>>>>>>> HASSAN >>> >>>
