Hi! On Mon, May 10, 2010 at 8:44 AM, Bradley, Stephen W. Mr. <bradlesw@xxxxxxxxxx> wrote: > Never thought of that, thanks. > > We use one IP address for each of the Squid servers and I gather from what you are saying that is also going to be a problem? It depends on the amount of simultaneous outgoing connections on the proxy, you need to evaluate that. I hit the limit once, it was on a 1000 computers network (used by college students, mainly), I had to increase the port-range to allow 40k connections, and it went stable on around 20k with peaks of ~35k :-S (that lasted a couple of minutes, and occurred at least three times a day). It was interesting. > > steve > > -----Original Message----- > From: Jose Ildefonso Camargo Tolosa [mailto:ildefonso.camargo@xxxxxxxxx] > Sent: Saturday, May 08, 2010 3:17 PM > To: Bradley, Stephen W. Mr. > Cc: mnhassan@xxxxxxx; Squid Users > Subject: Re: Increasing File Descriptors - Fixed!! > > Hi! > > Just one thought here: > > I believe there is a limit on the number of connections that can be > originated from a single IP (IPv4), so, I guess that you have > *several* external IPs and that you make squid use many of them, look > that file on your system: > > cat /proc/sys/net/ipv4/ip_local_port_range > > in my PC it is: 32768 to 61000, thus giving me a max of 28232 outgoing > connections per IP, that's usually "enough", but your case isn't a > "usual" one. > > I hope this helps, > > Ildefonso Camargo > > On Fri, May 7, 2010 at 8:32 AM, Bradley, Stephen W. Mr. > <bradlesw@xxxxxxxxxx> wrote: >> Got it resolved! >> >> cat /proc/sys/fs/file-max showed that I could go as high as 3,138,830 FDs. >> >> I changed the compile options to --with-maxfd=128000 and recompiled and installed it. >> >> I changed the line in my /etc/init.d/squid script to ulimit -HSn 128000 and restarted. >> >> I thought I had tried all this before but evidently not. >> >> If it almost held the load at 32,768 then at 128,000 I should have enough head room to keep us safe, for now. >> >> >> Thanks to all who responded. >> >> steve >> >> >> -----Original Message----- >> From: Nyamul Hassan [mailto:mnhassan@xxxxxxx] >> Sent: Thursday, May 06, 2010 4:15 PM >> To: Squid Users >> Subject: Re: Increasing File Descriptors >> >> He needs more FDs because this single box is handling 5000 users over >> a 400mbps connection. We run around 2,000 users on generic hardware, >> and have seen FDs as high as 20k. >> >> We use CentOS 5 and the following guide is a good place to increase >> the FD limit: >> http://www.cyberciti.biz/faq/linux-increase-the-maximum-number-of-open-files/ >> The command "cat /proc/sys/fs/file-max" shows how many maximum FDs >> your OS can handle. >> >> After you've made sure that your OS is doing your desired FD limit, >> please re-run Squid. Squid shows how many FDs it is configured for in >> its "General Runtime Information" (mgr:info in cli) from the CacheMgr >> interface. If this still shows lower than the OS limit you just saw >> earlier, then you might need to recompile Squid with the >> '--with-maxfd=<your-desired-fdmax>' flag set during "./configure" >> >> As a side note, if you are using Squid as a forward proxy, you might >> have better results with Squid 2.7x. >> >> Regards >> HASSAN >> >> >> On Fri, May 7, 2010 at 00:53, George Herbert <george.herbert@xxxxxxxxx> wrote: >>> >>> Do this: >>> >>> ulimit -Hn >>> >>> If the values is 32768 that's your current kernel/sys max value and >>> you're stuck. >>> >>> If it's more than 32768 (and my RHEL 5.3 box says 65536) then you >>> should be able to increase up to that value. Unless there's an >>> internal signed 16-bit int involved in FD tracking inside the Squid >>> code then something curious is happening... >>> >>> However - I'm curious as to why you'd need that many. I've had top >>> end systems with Squid clusters running with compiles of 16k file >>> descriptors and only ever really used 4-5k. What are you doing that >>> you need more than 32k? >>> >>> >>> -george >>> >>> On Thu, May 6, 2010 at 10:32 AM, Bradley, Stephen W. Mr. >>> <bradlesw@xxxxxxxxxx> wrote: >>> > Unfortunately won't work for me above 32768. >>> > >>> > I have the ulimit in the startup script and that works okay but I need more the 32768. >>> > >>> > :-( >>> > >>> > >>> > >>> > -----Original Message----- >>> > From: Ivan . [mailto:ivanhec@xxxxxxxxx] >>> > Sent: Thursday, May 06, 2010 5:17 AM >>> > To: Bradley, Stephen W. Mr. >>> > Cc: squid-users@xxxxxxxxxxxxxxx >>> > Subject: Re: Increasing File Descriptors >>> > >>> > worked for me >>> > >>> > http://paulgoscicki.com/archives/2007/01/squid-warning-your-cache-is-running-out-of-filedescriptors/ >>> > >>> > no recompile necessary >>> > >>> > >>> > On Thu, May 6, 2010 at 7:13 PM, Bradley, Stephen W. Mr. >>> > <bradlesw@xxxxxxxxxx> wrote: >>> >> I can't seem to get increase the number above 32768 no matter what I do. >>> >> >>> >> Ulimit during compile, sysctl.conf and everything else but no luck. >>> >> >>> >> >>> >> I have about 5,000 users on a 400mbit connection. >>> >> >>> >> Steve >>> >> >>> >> RHEL5 64bit with Squid 3.1.1 >>> > >>> >>> >>> >>> -- >>> -george william herbert >>> george.herbert@xxxxxxxxx >>> >> >
