Hi all,
I've installed Redhat Linux 8.0 and have now the problem that my ADSL
will not
work anymore. Before Redhat 7.2 was installed and all worked fine.
Unfortunately I forgot to save the old custumization. At the moment I
get always
a timeout when I try to connect to my DSL provider (German Telekom). I
assume
that my ethernet card population maybe wrong. According to the debug
output of
adsl-startscript the card should work in half-duplex mode but the kernel
has
full-duplex detected during boot? The hardware has not been changed.
Also to switch off the Redhat firewall has no effect. I'll append all my
logfiles in the hope that anybody can help me. On the other hand I´m total
frustrated after three days.
kernel log about ethernet card during booting:
kernel: eth1: NatSemi DP8381[56] at 0xd8925000, 00:02:e3:17:81:7a, IRQ 10.
kernel: eth1: link up.
kernel: eth1: Setting full-duplex based on negotiated link capability.
Output of iptables -L
Chain INPUT (policy ACCEPT)
target prot opt source destination
Chain FORWARD (policy ACCEPT)
target prot opt source destination
Chain OUTPUT (policy ACCEPT)
target prot opt source destination
Output of ifconfig eth1
eth1 Protokoll:Ethernet Hardware Adresse 00:02:E3:17:81:7A
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:100
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:10 Basisadresse:0x5000
Configuration of ifcfg-eth1 in /etc/sysconfig/network-scripts
DEVICE=eth1
BOOTPROTO=dhcp
ONBOOT=no
USERCTL=yes
PEERDNS=yes
TYPE=Ethernet
Configuration of ifcfg-ppp0 in /etc/sysconfig/network-scripts
USERCTL=yes
PEERDNS=yes
TYPE=xDSL
DEVICE=ppp0
BOOTPROTO=dialup
ONBOOT=no
PIDFILE=/var/run/pppoe-adsl.pid
FIREWALL=NONE
PING=.
PPPOE_TIMEOUT=80
LCP_FAILURE=3
LCP_INTERVAL=20
CLAMPMSS=1412
CONNECT_POLL=1
CONNECT_TIMEOUT=30
PERSIST=no
SYNCHRONOUS=yes
DEFROUTE=yes
USER='...../..................'
PROVIDER=1und1
ETH=eth1
After calling /sbin/ifup ppp0 I can find the following log records in
messages:
Jan 3 10:19:47 hugo kernel: eth1: Promiscuous mode enabled.
Jan 3 10:19:48 hugo kernel: CSLIP: code copyright 1989 Regents of the
University of California
Jan 3 10:19:48 hugo kernel: PPP generic driver version 2.4.2
Jan 3 10:19:48 hugo kernel: HDLC line discipline: version $Revision:
3.3 $, maxframe=4096
Jan 3 10:19:48 hugo kernel: N_HDLC line discipline registered.
Jan 3 10:19:48 hugo pppd[1594]: pppd 2.4.1 started by root, uid 0
Jan 3 10:19:48 hugo pppd[1594]: Using interface ppp0
Jan 3 10:19:48 hugo pppd[1594]: Connect: ppp0 <--> /dev/pts/4
Jan 3 10:19:48 hugo /etc/hotplug/net.agent: assuming ppp0 is already up
Jan 3 10:19:48 hugo pppoe[1595]: Changed pty line discipline to N_HDLC
for synchronous mode
Jan 3 10:20:19 hugo pppd[1594]: LCP: timeout sending Config-Requests
Jan 3 10:20:19 hugo pppd[1594]: Connection terminated.
Jan 3 10:20:19 hugo /etc/hotplug/net.agent: NET unregister event not
supported
Jan 3 10:20:23 hugo pppoe[1595]: Timeout waiting for PADO packets
Jan 3 10:20:23 hugo pppd[1594]: Exit.
tcpdump -i eth1 has the following output:
tcpdump: WARNING: eth1: no IPv4 address assigned
tcpdump: listening on eth1
10:19:48.529124 PPPoE PADI [Service-Name] [Host-Uniq UTF8]
10:19:53.527987 PPPoE PADI [Service-Name] [Host-Uniq UTF8]
10:20:03.527987 PPPoE PADI [Service-Name] [Host-Uniq UTF8]
adsl-start /etc/sysconfig/network-scripts/ifcfg-ppp0 with DEBUG=1
---------------------------------------------
* The following section contains information about your system
Fri Jan 3 11:09:55 CET 2003
Output of uname -a
Linux hugo 2.4.18-19.8.0 #1 Thu Dec 12 05:39:29 EST 2002 i686 athlon
i386 GNU/Linux
---------------------------------------------
* The following section contains information about your network
* interfaces. The one you chose for PPPoE should contain the words:
* 'UP' and 'RUNNING'. If it does not, you probably have an Ethernet
* driver problem.
Output of ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:E0:7D:AB:93:6F
inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:240 (240.0 b)
Interrupt:5 Base address:0xd000
eth1 Link encap:Ethernet HWaddr 00:02:E3:17:81:7A
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:130 errors:0 dropped:0 overruns:0 frame:0
TX packets:9 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:16648 (16.2 Kb) TX bytes:288 (288.0 b)
Interrupt:10 Base address:0x5000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:120 errors:0 dropped:0 overruns:0 frame:0
TX packets:120 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:9229 (9.0 Kb) TX bytes:9229 (9.0 Kb)
---------------------------------------------
* The following section contains information about kernel modules
* If the module for your Ethernet card is 'tulip', you might
* want to look for an updated version at http://www.scyld.com
Output of lsmod
Module Size Used by Not tainted
n_hdlc 8032 0
ppp_synctty 7936 0
ppp_async 9440 0 (unused)
ppp_generic 24380 0 [ppp_synctty ppp_async]
slhc 6756 0 [ppp_generic]
nls_iso8859-1 3516 1 (autoclean)
nls_cp437 5148 1 (autoclean)
vfat 13084 1 (autoclean)
fat 38712 0 (autoclean) [vfat]
sr_mod 18168 0 (autoclean)
via82cxxx_audio 23480 0 (autoclean)
uart401 8420 0 (autoclean) [via82cxxx_audio]
ac97_codec 13416 0 (autoclean) [via82cxxx_audio]
sound 74388 0 (autoclean) [via82cxxx_audio uart401]
soundcore 6532 4 (autoclean) [via82cxxx_audio sound]
parport_pc 19108 1 (autoclean)
lp 8996 0 (autoclean)
parport 37152 1 (autoclean) [parport_pc lp]
autofs 13348 0 (autoclean) (unused)
natsemi 19648 1
8139too 17704 1
mii 2156 0 [8139too]
iptable_filter 2412 0 (autoclean) (unused)
ip_tables 14936 1 [iptable_filter]
ide-scsi 10512 0
ide-cd 33608 0
cdrom 33696 0 [sr_mod ide-cd]
mousedev 5524 1
keybdev 2976 0 (unused)
hid 22244 0 (unused)
input 5920 0 [mousedev keybdev hid]
usb-uhci 26188 0 (unused)
usbcore 77024 1 [hid usb-uhci]
ext3 70336 2
jbd 52212 2 [ext3]
atp870u 23856 0 (unused)
sd_mod 13552 0 (unused)
scsi_mod 107176 4 [sr_mod ide-scsi atp870u sd_mod]
---------------------------------------------
* The following section lists your routing table.
* If you have an entry which starts with '0.0.0.0', you probably
* have defined a default route and gateway, and pppd will
* not create a default route using your ISP. Try getting
* rid of this route.
Output of netstat -n -r
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt
Iface
192.168.0.0 0.0.0.0 255.255.255.0 U 40 0 0
eth0
127.0.0.0 0.0.0.0 255.0.0.0 U 40 0 0 lo
---------------------------------------------
Contents of /etc/resolv.conf
* The following section lists DNS setup.
* If you can browse by IP address, but not name, suspect
* a DNS problem.
---------------------------------------------
* The following section lists /etc/ppp/options.
* You should have NOTHING in that file.
Contents of /etc/ppp/options
---------------------------------------------
* The following section identifies your Ethernet interface
* and user name. Some ISP's need 'username'; others
* need 'username@isp.com'. Try both
ETH=eth1; USER=...../........@online.de
---------------------------------------------
* The following section shows the pppd command we will invoke
pppd invocation
/usr/bin/setsid /usr/sbin/pppd pty '/usr/sbin/pppoe -p
/var/run/pppoe-adsl.pid.pppoe -I eth1 -T 80 -U -s -m 1412 ' debug
ipparam ppp0 linkname ppp0 noipdefault noauth default-asyncmap
defaultroute hide-password nodetach usepeerdns mtu 1492 mru 1492
noaccomp noccp nobsdcomp nodeflate nopcomp novj novjccomp user
...../........@online.de lcp-echo-interval 20 lcp-echo-failure 3 sync
debug
---------------------------------------------
using channel 4
Using interface ppp0
Connect: ppp0 <--> /dev/pts/4
sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x8ad05e5f>]
sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x8ad05e5f>]
sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x8ad05e5f>]
sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x8ad05e5f>]
sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x8ad05e5f>]
sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x8ad05e5f>]
sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x8ad05e5f>]
sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x8ad05e5f>]
sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x8ad05e5f>]
sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x8ad05e5f>]
LCP: timeout sending Config-Requests
Connection terminated.
Waiting for 1 child processes...
script /usr/sbin/pppoe -p /var/run/pppoe-adsl.pid.pppoe -I eth1 -T 80
-U -s -m 1412 -D /tmp/pppoe-debug-3274/pppoe-debug.txt-0, pid 3341
pppoe: Timeout waiting for PADO packets
Script /usr/sbin/pppoe -p /var/run/pppoe-adsl.pid.pppoe -I eth1 -T 80 -U
-s -m 1412 -D /tmp/pppoe-debug-3274/pppoe-debug.txt-0 finished (pid
3341), status = 0x1
---------------------------------------------
* The following section is an extract from your log.
* Look for error messages from pppd, such as
* a lack of kernel support for PPP, authentication failure
* etc.
Extract from /var/log/messages
Jan 2 22:59:09 hugo pppoe[7942]: Changed pty line discipline to N_HDLC
for synchronous mode
Jan 2 22:59:09 hugo /etc/hotplug/net.agent: assuming ppp0 is already up
Jan 2 22:59:40 hugo pppd[7941]: LCP: timeout sending Config-Requests
Jan 2 22:59:40 hugo pppd[7941]: Connection terminated.
Jan 2 22:59:44 hugo pppoe[7942]: Timeout waiting for PADO packets
Jan 2 22:59:44 hugo pppd[7941]: Exit.
Jan 2 23:07:01 hugo pppd[12269]: pppd 2.4.1 started by root, uid 0
Jan 2 23:07:01 hugo /etc/hotplug/net.agent: assuming ppp0 is already up
Jan 2 23:07:01 hugo pppd[12269]: Using interface ppp0
Jan 2 23:07:01 hugo pppd[12269]: Connect: ppp0 <--> /dev/pts/3
Jan 2 23:07:01 hugo pppoe[12270]: Changed pty line discipline to N_HDLC
for synchronous mode
Jan 2 23:07:32 hugo pppd[12269]: LCP: timeout sending Config-Requests
Jan 2 23:07:32 hugo pppd[12269]: Connection terminated.
Jan 2 23:07:36 hugo pppoe[12270]: Timeout waiting for PADO packets
Jan 2 23:07:36 hugo pppd[12269]: Exit.
Jan 2 23:07:41 hugo pppd[12291]: pppd 2.4.1 started by root, uid 0
Jan 2 23:07:41 hugo pppd[12291]: Using interface ppp0
Jan 2 23:07:41 hugo pppd[12291]: Connect: ppp0 <--> /dev/pts/3
Jan 2 23:07:41 hugo pppoe[12292]: Changed pty line discipline to N_HDLC
for synchronous mode
Jan 2 23:07:41 hugo /etc/hotplug/net.agent: assuming ppp0 is already up
Jan 2 23:08:12 hugo pppd[12291]: LCP: timeout sending Config-Requests
Jan 2 23:08:12 hugo pppd[12291]: Connection terminated.
Jan 2 23:08:16 hugo pppoe[12292]: Timeout waiting for PADO packets
Jan 2 23:08:16 hugo pppd[12291]: Exit.
Jan 2 23:08:21 hugo pppd[12326]: pppd 2.4.1 started by root, uid 0
Jan 2 23:08:21 hugo pppd[12326]: Using interface ppp0
Jan 2 23:08:21 hugo pppd[12326]: Connect: ppp0 <--> /dev/pts/3
Jan 2 23:08:21 hugo pppoe[12327]: Changed pty line discipline to N_HDLC
for synchronous mode
Jan 2 23:08:21 hugo /etc/hotplug/net.agent: assuming ppp0 is already up
Jan 2 23:08:52 hugo pppd[12326]: LCP: timeout sending Config-Requests
Jan 2 23:08:52 hugo pppd[12326]: Connection terminated.
Jan 2 23:08:56 hugo pppoe[12327]: Timeout waiting for PADO packets
Jan 2 23:08:56 hugo pppd[12326]: Exit.
Jan 2 23:09:01 hugo pppd[12346]: pppd 2.4.1 started by root, uid 0
Jan 2 23:09:01 hugo pppd[12346]: Using interface ppp0
Jan 2 23:09:01 hugo pppd[12346]: Connect: ppp0 <--> /dev/pts/3
Jan 2 23:09:01 hugo pppoe[12347]: Changed pty line discipline to N_HDLC
for synchronous mode
Jan 2 23:09:01 hugo /etc/hotplug/net.agent: assuming ppp0 is already up
Jan 2 23:09:32 hugo pppd[12346]: LCP: timeout sending Config-Requests
Jan 2 23:09:32 hugo pppd[12346]: Connection terminated.
Jan 2 23:09:36 hugo pppoe[12347]: Timeout waiting for PADO packets
Jan 2 23:09:36 hugo pppd[12346]: Exit.
Jan 2 23:11:25 hugo pppd[12382]: pppd 2.4.1 started by root, uid 0
Jan 2 23:11:25 hugo /etc/hotplug/net.agent: assuming ppp0 is already up
Jan 2 23:11:25 hugo pppd[12382]: Using interface ppp0
Jan 2 23:11:25 hugo pppd[12382]: Connect: ppp0 <--> /dev/pts/3
Jan 2 23:11:25 hugo pppoe[12383]: Changed pty line discipline to N_HDLC
for synchronous mode
Jan 2 23:11:56 hugo pppd[12382]: LCP: timeout sending Config-Requests
Jan 2 23:11:56 hugo pppd[12382]: Connection terminated.
Jan 2 23:12:00 hugo pppoe[12383]: Timeout waiting for PADO packets
Jan 2 23:12:00 hugo pppd[12382]: Exit.
Jan 2 23:12:05 hugo pppd[12402]: pppd 2.4.1 started by root, uid 0
Jan 2 23:12:05 hugo pppd[12402]: Using interface ppp0
Jan 2 23:12:05 hugo pppd[12402]: Connect: ppp0 <--> /dev/pts/3
Jan 2 23:12:05 hugo pppoe[12403]: Changed pty line discipline to N_HDLC
for synchronous mode
Jan 2 23:12:05 hugo /etc/hotplug/net.agent: assuming ppp0 is already up
Jan 2 23:12:36 hugo pppd[12402]: LCP: timeout sending Config-Requests
Jan 2 23:12:36 hugo pppd[12402]: Connection terminated.
Jan 2 23:12:40 hugo pppoe[12403]: Timeout waiting for PADO packets
Jan 2 23:12:40 hugo pppd[12402]: Exit.
Jan 2 23:12:45 hugo pppd[12423]: pppd 2.4.1 started by root, uid 0
Jan 2 23:12:45 hugo pppd[12423]: Using interface ppp0
Jan 2 23:12:45 hugo pppd[12423]: Connect: ppp0 <--> /dev/pts/3
Jan 2 23:12:45 hugo pppoe[12424]: Changed pty line discipline to N_HDLC
for synchronous mode
Jan 2 23:12:45 hugo /etc/hotplug/net.agent: assuming ppp0 is already up
Jan 2 23:13:16 hugo pppd[12423]: LCP: timeout sending Config-Requests
Jan 2 23:13:16 hugo pppd[12423]: Connection terminated.
Jan 2 23:13:20 hugo pppoe[12424]: Timeout waiting for PADO packets
Jan 2 23:13:20 hugo pppd[12423]: Exit.
Jan 2 23:13:25 hugo pppd[12455]: pppd 2.4.1 started by root, uid 0
Jan 2 23:13:25 hugo pppd[12455]: Using interface ppp0
Jan 2 23:13:25 hugo pppd[12455]: Connect: ppp0 <--> /dev/pts/3
Jan 2 23:13:25 hugo pppoe[12456]: Changed pty line discipline to N_HDLC
for synchronous mode
Jan 2 23:13:25 hugo /etc/hotplug/net.agent: assuming ppp0 is already up
Jan 2 23:13:56 hugo pppd[12455]: LCP: timeout sending Config-Requests
Jan 2 23:13:56 hugo pppd[12455]: Connection terminated.
Jan 2 23:14:00 hugo pppoe[12456]: Timeout waiting for PADO packets
Jan 2 23:14:00 hugo pppd[12455]: Exit.
Jan 2 23:55:28 hugo pppd[1147]: pppd 2.4.1 started by root, uid 0
Jan 2 23:55:28 hugo pppd[1147]: Using interface ppp0
Jan 2 23:55:28 hugo pppd[1147]: Connect: ppp0 <--> /dev/pts/2
Jan 2 23:55:28 hugo /etc/hotplug/net.agent: assuming ppp0 is already up
Jan 2 23:55:28 hugo pppoe[1148]: Changed pty line discipline to N_HDLC
for synchronous mode
Jan 2 23:55:59 hugo pppd[1147]: LCP: timeout sending Config-Requests
Jan 2 23:55:59 hugo pppd[1147]: Connection terminated.
Jan 2 23:56:03 hugo pppoe[1148]: Timeout waiting for PADO packets
Jan 2 23:56:03 hugo pppd[1147]: Exit.
Jan 2 23:56:52 hugo pppd[1691]: pppd 2.4.1 started by root, uid 0
Jan 2 23:56:52 hugo /etc/hotplug/net.agent: assuming ppp0 is already up
Jan 2 23:56:52 hugo pppd[1691]: Using interface ppp0
Jan 2 23:56:52 hugo pppd[1691]: Connect: ppp0 <--> /dev/pts/2
Jan 2 23:56:52 hugo pppoe[1692]: Changed pty line discipline to N_HDLC
for synchronous mode
Jan 2 23:56:59 hugo pppd[1781]: pppd 2.4.1 started by root, uid 0
Jan 2 23:56:59 hugo /etc/hotplug/net.agent: assuming ppp1 is already up
Jan 2 23:56:59 hugo pppd[1781]: Using interface ppp1
Jan 2 23:56:59 hugo pppd[1781]: Connect: ppp1 <--> /dev/pts/3
Jan 2 23:56:59 hugo pppoe[1782]: Changed pty line discipline to N_HDLC
for synchronous mode
Jan 2 23:57:23 hugo pppd[1691]: LCP: timeout sending Config-Requests
Jan 2 23:57:23 hugo pppd[1691]: Connection terminated.
Jan 2 23:57:27 hugo pppoe[1692]: Timeout waiting for PADO packets
Jan 2 23:57:27 hugo pppd[1691]: Exit.
Jan 2 23:57:30 hugo pppd[1781]: LCP: timeout sending Config-Requests
Jan 2 23:57:30 hugo pppd[1781]: Connection terminated.
Jan 2 23:57:34 hugo pppoe[1782]: Timeout waiting for PADO packets
Jan 2 23:57:34 hugo pppd[1781]: Exit.
Jan 3 00:00:08 hugo pppd[2247]: pppd 2.4.1 started by root, uid 0
Jan 3 00:00:08 hugo /etc/hotplug/net.agent: assuming ppp0 is already up
Jan 3 00:00:08 hugo pppd[2247]: Using interface ppp0
Jan 3 00:00:08 hugo pppd[2247]: Connect: ppp0 <--> /dev/pts/2
Jan 3 00:00:08 hugo pppoe[2248]: Changed pty line discipline to N_HDLC
for synchronous mode
Jan 3 00:00:39 hugo pppd[2247]: LCP: timeout sending Config-Requests
Jan 3 00:00:39 hugo pppd[2247]: Connection terminated.
Jan 3 00:00:43 hugo pppoe[2248]: Timeout waiting for PADO packets
Jan 3 00:00:43 hugo pppd[2247]: Exit.
Jan 3 10:19:48 hugo pppd[1594]: pppd 2.4.1 started by root, uid 0
Jan 3 10:19:48 hugo pppd[1594]: Using interface ppp0
Jan 3 10:19:48 hugo pppd[1594]: Connect: ppp0 <--> /dev/pts/4
Jan 3 10:19:48 hugo /etc/hotplug/net.agent: assuming ppp0 is already up
Jan 3 10:19:48 hugo pppoe[1595]: Changed pty line discipline to N_HDLC
for synchronous mode
Jan 3 10:20:19 hugo pppd[1594]: LCP: timeout sending Config-Requests
Jan 3 10:20:19 hugo pppd[1594]: Connection terminated.
Jan 3 10:20:23 hugo pppoe[1595]: Timeout waiting for PADO packets
Jan 3 10:20:23 hugo pppd[1594]: Exit.
Jan 3 10:34:14 hugo pppd[2215]: pppd 2.4.1 started by root, uid 0
Jan 3 10:34:14 hugo /etc/hotplug/net.agent: assuming ppp0 is already up
Jan 3 10:34:14 hugo pppd[2215]: Using interface ppp0
Jan 3 10:34:14 hugo pppd[2215]: Connect: ppp0 <--> /dev/pts/4
Jan 3 10:34:14 hugo pppoe[2216]: Changed pty line discipline to N_HDLC
for synchronous mode
Jan 3 10:34:45 hugo pppd[2215]: LCP: timeout sending Config-Requests
Jan 3 10:34:45 hugo pppd[2215]: Connection terminated.
Jan 3 10:34:49 hugo pppoe[2216]: Timeout waiting for PADO packets
Jan 3 10:34:49 hugo pppd[2215]: Exit.
Jan 3 10:42:44 hugo pppd[2608]: pppd 2.4.1 started by root, uid 0
Jan 3 10:42:44 hugo /etc/hotplug/net.agent: assuming ppp0 is already up
Jan 3 10:42:44 hugo pppd[2608]: Using interface ppp0
Jan 3 10:42:44 hugo pppd[2608]: Connect: ppp0 <--> /dev/pts/4
Jan 3 10:42:44 hugo pppoe[2609]: Changed pty line discipline to N_HDLC
for synchronous mode
Jan 3 10:43:15 hugo pppd[2608]: LCP: timeout sending Config-Requests
Jan 3 10:43:15 hugo pppd[2608]: Connection terminated.
Jan 3 10:43:19 hugo pppoe[2609]: Timeout waiting for PADO packets
Jan 3 10:43:19 hugo pppd[2608]: Exit.
Jan 3 11:09:56 hugo pppd[3340]: pppd 2.4.1 started by root, uid 0
Jan 3 11:09:56 hugo /etc/hotplug/net.agent: assuming ppp0 is already up
Jan 3 11:09:56 hugo pppd[3340]: Using interface ppp0
Jan 3 11:09:56 hugo pppd[3340]: Connect: ppp0 <--> /dev/pts/4
Jan 3 11:09:56 hugo pppoe[3341]: Changed pty line discipline to N_HDLC
for synchronous mode
Jan 3 11:10:27 hugo pppd[3340]: LCP: timeout sending Config-Requests
Jan 3 11:10:27 hugo pppd[3340]: Connection terminated.
Jan 3 11:10:31 hugo pppoe[3341]: Timeout waiting for PADO packets
Jan 3 11:10:31 hugo pppd[3340]: Exit.
Fri Jan 3 11:10:32 CET 2003
---------------------------------------------
* The following section is a dump of the packets
* sent and received by rp-pppoe. If you don't see
* any output, it's an Ethernet driver problem. If you only
* see three PADI packets and nothing else, check your cables
* and modem. Make sure the modem lights flash when you try
* to connect. Check that your Ethernet card is in
* half-duplex, 10Mb/s mode. If all else fails,
* try using pppoe-sniff.
rp-pppoe debugging dump
rp-pppoe-3.4
11:09:56.968 SENT PPPoE Discovery (8863) PADI sess-id 0 length 12
SourceAddr 00:02:e3:17:81:7a DestAddr ff:ff:ff:ff:ff:ff
01 01 00 00 01 03 00 04 0d 0d 00 00 ............
11:10:01.967 SENT PPPoE Discovery (8863) PADI sess-id 0 length 12
SourceAddr 00:02:e3:17:81:7a DestAddr ff:ff:ff:ff:ff:ff
01 01 00 00 01 03 00 04 0d 0d 00 00 ............
11:10:11.967 SENT PPPoE Discovery (8863) PADI sess-id 0 length 12
SourceAddr 00:02:e3:17:81:7a DestAddr ff:ff:ff:ff:ff:ff
01 01 00 00 01 03 00 04 0d 0d 00 00 ............
--
Psyche-list mailing list
Psyche-list@redhat.com
https://listman.redhat.com/mailman/listinfo/psyche-list
