Sorry, partition "types" , not labels. Thanks, Tom Callahan TESSCO Technologies Desk: (410)-229-1361 Cell: (443)-506-6216 Email: callahant@xxxxxxxxxx A real engineer only resorts to documentation when the keyboard dents on the forehead get too noticeable. Tom Callahan wrote: >Make sure the partition labels in fdisk are set to "Linux Raid Autodetect" > >Thanks, > >Tom Callahan >TESSCO Technologies >Desk: (410)-229-1361 >Cell: (443)-506-6216 >Email: callahant@xxxxxxxxxx > >A real engineer only resorts to documentation when the keyboard dents on the forehead get too noticeable. > > > >baran.yurdagul@xxxxxxxxxxxxxxx wrote: > > > >>Can you make some full fsck to filesystem ? >> >>-----Original Message----- >>From: redhat-list-bounces@xxxxxxxxxx >>[mailto:redhat-list-bounces@xxxxxxxxxx] On Behalf Of Marc Leveille >>Sent: Friday, January 27, 2006 3:50 PM >>To: General Red Hat Linux discussion list >>Subject: RE: Help with ES v3 Raid1 (Mirror) >> >>Hi, I used ext3. I will try again today using ext2 as I have no other >>idea. I only have experience with hardware raid with Windows. >> >>thanks >> >>Marc >> >>On Fri, 2006-01-27 at 08:09 +0200, baran.yurdagul@xxxxxxxxxxxxxxx wrote: >> >> >> >> >>>Which option did u use while creating the filesystem, ext2 or ext3 via >>>mkfs command ? >>> >>>-----Original Message----- >>>From: redhat-list-bounces@xxxxxxxxxx >>>[mailto:redhat-list-bounces@xxxxxxxxxx] On Behalf Of Marc Leveille >>>Sent: Thursday, January 26, 2006 9:52 PM >>>To: redhat-list@xxxxxxxxxx >>>Subject: Help with ES v3 Raid1 (Mirror) >>> >>>Hi, I'm trying to setup a Raid1 mirror between 2 hard drives. I have >>> >>> >>> >>> >>the >> >> >> >> >>>following. >>> >>>1- SDA 36gig System disk >>>2- SDB 36gig blank >>>3- SDC 36gig blank >>> >>>I'm trying to Mirror SDB to SDC by doing the following. >>> >>>1- By using FDisk I created SDB1 and SDC1 on each drive. >>>2- I then makefs ext3 for each partition. >>>3- Then I used mkadm --create /dev/md0 --level=1 >>>--raid-devices=2 /dev/sdb1 /dev/sdc1 >>> >>>I ran watch cat /proc/mdstat until the process was completed. >>>4- when it was complete I tested the mount using mount -t >>>ext3 /dev/md0 /home/apps and it mounted and I was able to open it. >>>5- I then edited fstab with /dev/md0 /home/apps ext3 defaults 1 2 and >>>rebooted. >>>6- I now get the following error at boot. >>> >>>FSCK.ext3 /dev/mdo the superblock could not be read or does not >>> >>> >>> >>> >>describe >> >> >> >> >>>a correct EXT2 Filesystem.......bla bla and asks to run E2FSCK -B 8193 >>> >>>7- I used Vi and comented out the mount in fstab and re-booted. I >>> >>> >>> >>> >>tried >> >> >> >> >>>to manually mount the drive the same way as (Item #4) and it now fails >>>Mount: Wrong FS Type. >>> >>>Any ideas as to what I need to do. Sould I use ext3 ? >>> >>>thanks >>> >>>Marc >>> >>>-- >>>redhat-list mailing list >>>unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe >>>https://www.redhat.com/mailman/listinfo/redhat-list >>> >>> >>> >>> >>> >>> >>> >>************************************************************************ >> >> >> >> >>>Bu elektronik posta ve onunla iletilen butun dosyalar sadece >>> >>> >>> >>> >>gondericisi tarafindan almasi amaclanan yetkili gercek ya da tuzel >>kisinin kullanimi icindir. Eger soz konusu yetkili alici degilseniz bu >>elektronik postanin icerigini aciklamaniz, kopyalamaniz, yonlendirmeniz >>ve kullanmaniz kesinlikle yasaktir ve bu elektronik postayi derhal >>silmeniz gerekmektedir. >> >> >> >> >>>TURKCELL bu mesajin icerdigi bilgilerin dogrulugu veya eksiksiz oldugu >>> >>> >>> >>> >>konusunda herhangi bir garanti vermemektedir. Bu nedenle bu bilgilerin >>ne sekilde olursa olsun iceriginden, iletilmesinden, alinmasindan ve >>saklanmasindan sorumlu degildir. Bu mesajdaki gorusler yalnizca gonderen >>kisiye aittir ve TURKCELLin goruslerini yansitmayabilir >> >> >> >> >>>Bu e-posta bilinen butun bilgisayar viruslerine karsi taranmistir. >>> >>> >>> >>> >>> >>************************************************************************ >> >> >> >> >>>This e-mail and any files transmitted with it are confidential and >>> >>> >>> >>> >>intended solely for the use of the individual or entity to whom they are >>addressed. If you are not the intended recipient you are hereby notified >>that any dissemination, forwarding, copying or use of any of the >>information is strictly prohibited, and the e-mail should immediately be >>deleted. >> >> >> >> >>>TURKCELL makes no warranty as to the accuracy or completeness of any >>> >>> >>> >>> >>information contained in this message and hereby excludes any liability >>of any kind for the information contained therein or for the information >>transmission, reception, storage or use of such in any way whatsoever. >>The opinions expressed in this message belong to sender alone and may >>not necessarily reflect the opinions of TURKCELL. >> >> >> >> >>>This e-mail has been scanned for all known computer viruses. >>> >>> >>> >>> >>> >>************************************************************************ >> >> >> >> >>> >>> >>> >>> >> >> >> >> > > > -- redhat-list mailing list unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe https://www.redhat.com/mailman/listinfo/redhat-list
