On 26 August 2011 23:26, Timothy D. Lenz <tlenz@xxxxxxxxxx> wrote: > um, no, that was the email that mdadm sends I thought. And it says problem > is sdb in each case. Though I was wondering why each one said [U_] instead > of [_U]. Here is the smartctl for sda and below that will be for sdb > > ====================================================================== > vorg@x64VDR:~$ sudo smartctl -a /dev/sda > smartctl 5.41 2011-06-09 r3365 [x86_64-linux-2.6.34.20100610.1] (local > build) > Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net > > === START OF INFORMATION SECTION === > Model Family: Seagate Barracuda 7200.11 > Device Model: ST3500320AS > Serial Number: 9QM7M86S > LU WWN Device Id: 5 000c50 01059c636 > Firmware Version: SD1A > User Capacity: 500,107,862,016 bytes [500 GB] > Sector Size: 512 bytes logical/physical > Device is: In smartctl database [for details use: -P show] > ATA Version is: 8 > ATA Standard is: ATA-8-ACS revision 4 > Local Time is: Fri Aug 26 15:23:41 2011 MST > SMART support is: Available - device has SMART capability. > SMART support is: Enabled > > === START OF READ SMART DATA SECTION === > SMART overall-health self-assessment test result: PASSED > > General SMART Values: > Offline data collection status: (0x82) Offline data collection activity > was completed without error. > Auto Offline Data Collection: > Enabled. > Self-test execution status: ( 0) The previous self-test routine > completed > without error or no self-test has > ever > been run. > Total time to complete Offline > data collection: ( 650) seconds. > Offline data collection > capabilities: (0x7b) SMART execute Offline immediate. > Auto Offline data collection on/off > support. > Suspend Offline collection upon new > command. > Offline surface scan supported. > Self-test supported. > Conveyance Self-test supported. > Selective Self-test supported. > SMART capabilities: (0x0003) Saves SMART data before entering > power-saving mode. > Supports SMART auto save timer. > Error logging capability: (0x01) Error logging supported. > General Purpose Logging supported. > Short self-test routine > recommended polling time: ( 1) minutes. > Extended self-test routine > recommended polling time: ( 119) minutes. > Conveyance self-test routine > recommended polling time: ( 2) minutes. > SCT capabilities: (0x103b) SCT Status supported. > SCT Error Recovery Control supported. > SCT Feature Control supported. > SCT Data Table supported. > > SMART Attributes Data Structure revision number: 10 > Vendor Specific SMART Attributes with Thresholds: > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED > WHEN_FAILED RAW_VALUE > 1 Raw_Read_Error_Rate 0x000f 114 100 006 Pre-fail Always > - 83309768 > 3 Spin_Up_Time 0x0003 094 094 000 Pre-fail Always > - 0 > 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always > - 13 > 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always > - 0 > 7 Seek_Error_Rate 0x000f 071 060 030 Pre-fail Always > - 13556066 > 9 Power_On_Hours 0x0032 094 094 000 Old_age Always > - 5406 > 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always > - 0 > 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always > - 13 > 184 End-to-End_Error 0x0032 100 100 099 Old_age Always > - 0 > 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always > - 0 > 188 Command_Timeout 0x0032 100 100 000 Old_age Always > - 0 > 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always > - 0 > 190 Airflow_Temperature_Cel 0x0022 067 065 045 Old_age Always > - 33 (Min/Max 30/35) > 194 Temperature_Celsius 0x0022 033 040 000 Old_age Always > - 33 (0 21 0 0) > 195 Hardware_ECC_Recovered 0x001a 058 033 000 Old_age Always > - 83309768 > 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always > - 0 > 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline > - 0 > 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always > - 0 > > SMART Error Log Version: 1 > No Errors Logged > > SMART Self-test log structure revision number 1 > No self-tests have been logged. [To run self-tests, use: smartctl -t] > > > SMART Selective self-test log data structure revision number 1 > SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS > 1 0 0 Not_testing > 2 0 0 Not_testing > 3 0 0 Not_testing > 4 0 0 Not_testing > 5 0 0 Not_testing > Selective self-test flags (0x0): > After scanning selected spans, do NOT read-scan remainder of disk. > If Selective self-test is pending on power-up, resume after 0 minute delay > On 8/26/2011 2:25 PM, Mathias Burén wrote: >> >> smartctl -a /dev/sda > > ====================================================================== > > vorg@x64VDR:~$ sudo smartctl -a /dev/sdb > smartctl 5.41 2011-06-09 r3365 [x86_64-linux-2.6.34.20100610.1] (local > build) > Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net > > Vendor: /1:0:0:0 > Product: > User Capacity: 600,332,565,813,390,450 bytes [600 PB] > Logical block size: 774843950 bytes > scsiModePageOffset: response length too short, resp_len=47 offset=50 > bd_len=46 >>> Terminate command early due to bad response to IEC mode page > A mandatory SMART command failed: exiting. To continue, add one or more '-T > permissive' options. > Indeed, sorry. 600 PB... where did you get that drive? ;) /M ��.n��������+%������w��{.n�����{����w��ܨ}���Ơz�j:+v�����w����ޙ��&�)ߡ�a����z�ޗ���ݢj��w�f
