um, no, that was the email that mdadm sends I thought. And it says
problem is sdb in each case. Though I was wondering why each one said
[U_] instead of [_U]. Here is the smartctl for sda and below that will
be for sdb
======================================================================
vorg@x64VDR:~$ sudo smartctl -a /dev/sda
smartctl 5.41 2011-06-09 r3365 [x86_64-linux-2.6.34.20100610.1] (local
build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.11
Device Model: ST3500320AS
Serial Number: 9QM7M86S
LU WWN Device Id: 5 000c50 01059c636
Firmware Version: SD1A
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Fri Aug 26 15:23:41 2011 MST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test
has ever
been run.
Total time to complete Offline
data collection: ( 650) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 119) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103b) SCT Status supported.
SCT Error Recovery Control
supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 114 100 006 Pre-fail
Always - 83309768
3 Spin_Up_Time 0x0003 094 094 000 Pre-fail
Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age
Always - 13
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000f 071 060 030 Pre-fail
Always - 13556066
9 Power_On_Hours 0x0032 094 094 000 Old_age
Always - 5406
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age
Always - 13
184 End-to-End_Error 0x0032 100 100 099 Old_age Always
- 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always
- 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always
- 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always
- 0
190 Airflow_Temperature_Cel 0x0022 067 065 045 Old_age Always
- 33 (Min/Max 30/35)
194 Temperature_Celsius 0x0022 033 040 000 Old_age Always
- 33 (0 21 0 0)
195 Hardware_ECC_Recovered 0x001a 058 033 000 Old_age Always
- 83309768
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always
- 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always
- 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay
On 8/26/2011 2:25 PM, Mathias Burén wrote:
smartctl -a /dev/sda
======================================================================
vorg@x64VDR:~$ sudo smartctl -a /dev/sdb
smartctl 5.41 2011-06-09 r3365 [x86_64-linux-2.6.34.20100610.1] (local
build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
Vendor: /1:0:0:0
Product:
User Capacity: 600,332,565,813,390,450 bytes [600 PB]
Logical block size: 774843950 bytes
scsiModePageOffset: response length too short, resp_len=47 offset=50
bd_len=46
>> Terminate command early due to bad response to IEC mode page
A mandatory SMART command failed: exiting. To continue, add one or more
'-T permissive' options.
--
To unsubscribe from this list: send the line "unsubscribe linux-raid" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
