Hello,
i am used pegetron freescale processor board. it that when i enter into minicom its not getting the correct booting....see this what i am getting .
ariem@ariem-desktop:~$ minicom -s
Welcome to minicom 2.3
OPTIONS: I18n
Compiled on Oct 24 2008, 06:37:44.
Port /dev/ttyUSB0
Press CTRL-A Z for help on special keys
++Initializing SPI-NOR flash...
JEDEC ID: 0xbf:0x25:0x4a
SPI NOR: block_size=0x10000, blocks=0x40, start=0x00000000, end=0x00400000
... Read from 0x1fef0000-0x1ff00000 at 0x00080000: .
... Read from 0x1fee3000-0x1fee4000 at 0x0008f000: .
PMIC ID: 0x000041d0 [Rev: 2.0]
[Warning] FEC not connect right PHY: ID=0
FEC: [ HALF_DUPLEX ] [ disconnected ] [ 10M bps ]:
Ethernet mxc_fec: MAC address 00:00:45:67:89:ab
No IP info for device!
Reset reason: Power-on reset
fis/fconfig from SPI-NOR
Boot switch: INTERNAL
EXPANSION: SPI-NOR: eCSPI1
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version FSL 200910_P1 - built 16:07:20, Jul 15 2009
Platform: MX51 Babbage (Freescale i.MX51 based) PASS 2.0 [x32 DDR]
Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc.
Copyright (C) 2003, 2004, 2005, 2006 eCosCentric Limited
RAM: 0x00000000-0x1ff00000, [0x00094fb8-0x1fee1000] available
FLASH: 0x00000000 - 0x400000, 64 blocks of 0x00010000 bytes each.
== Executing boot script in 1.000 seconds - enter ^C to abort
RedBoot> pmic 15 0x00400022
val: 0x00400022
RedBoot> mfill -b 0x73f88000 -p 0x01025200 -l 0x04 -4
RedBoot> mfill -b 0x73f84000 -p 0x20 -l 0x04 -4
RedBoot> fis load kernel
... Read from 0x1fef0000-0x1feff000 at 0x00080000: .
... Read from 0x00100000-0x00380000 at 0x00100000: .
RedBoot> e -c "root=/dev/sda1 ro quite splash"
entry=0x90008000, target=0x90008000
Using base address 0x00100000 and length 0x00280000
Uncompressing Linux................................................................................................................................ done, bo.
Welcome to minicom 2.3
OPTIONS: I18n
Compiled on Oct 24 2008, 06:37:44.
Port /dev/ttyUSB0
Press CTRL-A Z for help on special keys
++Initializing SPI-NOR flash...
JEDEC ID: 0xbf:0x25:0x4a
SPI NOR: block_size=0x10000, blocks=0x40, start=0x00000000, end=0x00400000
... Read from 0x1fef0000-0x1ff00000 at 0x00080000: .
... Read from 0x1fee3000-0x1fee4000 at 0x0008f000: .
PMIC ID: 0x000041d0 [Rev: 2.0]
[Warning] FEC not connect right PHY: ID=0
FEC: [ HALF_DUPLEX ] [ disconnected ] [ 10M bps ]:
Ethernet mxc_fec: MAC address 00:00:45:67:89:ab
No IP info for device!
Reset reason: Power-on reset
fis/fconfig from SPI-NOR
Boot switch: INTERNAL
EXPANSION: SPI-NOR: eCSPI1
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version FSL 200910_P1 - built 16:07:20, Jul 15 2009
Platform: MX51 Babbage (Freescale i.MX51 based) PASS 2.0 [x32 DDR]
Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc.
Copyright (C) 2003, 2004, 2005, 2006 eCosCentric Limited
RAM: 0x00000000-0x1ff00000, [0x00094fb8-0x1fee1000] available
FLASH: 0x00000000 - 0x400000, 64 blocks of 0x00010000 bytes each.
== Executing boot script in 1.000 seconds - enter ^C to abort
RedBoot> pmic 15 0x00400022
val: 0x00400022
RedBoot> mfill -b 0x73f88000 -p 0x01025200 -l 0x04 -4
RedBoot> mfill -b 0x73f84000 -p 0x20 -l 0x04 -4
RedBoot> fis load kernel
... Read from 0x1fef0000-0x1feff000 at 0x00080000: .
... Read from 0x00100000-0x00380000 at 0x00100000: .
RedBoot> e -c "root=/dev/sda1 ro quite splash"
entry=0x90008000, target=0x90008000
Using base address 0x00100000 and length 0x00280000
Uncompressing Linux................................................................................................................................ done, bo.
after this i am not getting anything.what to do?
