Signed-off-by: Manuel Lauss <manuel.lauss@xxxxxxxxxxxxxx>
---
arch/mips/alchemy/devboards/Makefile | 16 +-
arch/mips/alchemy/devboards/db1200.c | 705 ++++++++++++++++++++++
arch/mips/alchemy/devboards/db1200/Makefile | 1 -
arch/mips/alchemy/devboards/db1200/platform.c | 648 --------------------
arch/mips/alchemy/devboards/db1200/setup.c | 81 ---
arch/mips/alchemy/devboards/db1x00.c | 256 ++++++++
arch/mips/alchemy/devboards/db1x00/Makefile | 8 -
arch/mips/alchemy/devboards/db1x00/board_setup.c | 108 ----
arch/mips/alchemy/devboards/db1x00/platform.c | 206 -------
arch/mips/alchemy/devboards/pb1100.c | 167 +++++
arch/mips/alchemy/devboards/pb1100/Makefile | 8 -
arch/mips/alchemy/devboards/pb1100/board_setup.c | 127 ----
arch/mips/alchemy/devboards/pb1100/platform.c | 77 ---
arch/mips/alchemy/devboards/pb1200.c | 464 ++++++++++++++
arch/mips/alchemy/devboards/pb1200/Makefile | 5 -
arch/mips/alchemy/devboards/pb1200/board_setup.c | 174 ------
arch/mips/alchemy/devboards/pb1200/platform.c | 339 -----------
arch/mips/alchemy/devboards/pb1500.c | 198 ++++++
arch/mips/alchemy/devboards/pb1500/Makefile | 8 -
arch/mips/alchemy/devboards/pb1500/board_setup.c | 139 -----
arch/mips/alchemy/devboards/pb1500/platform.c | 94 ---
arch/mips/alchemy/devboards/pb1550.c | 178 ++++++
arch/mips/alchemy/devboards/pb1550/Makefile | 8 -
arch/mips/alchemy/devboards/pb1550/board_setup.c | 80 ---
arch/mips/alchemy/devboards/pb1550/platform.c | 140 -----
25 files changed, 1976 insertions(+), 2259 deletions(-)
create mode 100644 arch/mips/alchemy/devboards/db1200.c
delete mode 100644 arch/mips/alchemy/devboards/db1200/Makefile
delete mode 100644 arch/mips/alchemy/devboards/db1200/platform.c
delete mode 100644 arch/mips/alchemy/devboards/db1200/setup.c
create mode 100644 arch/mips/alchemy/devboards/db1x00.c
delete mode 100644 arch/mips/alchemy/devboards/db1x00/Makefile
delete mode 100644 arch/mips/alchemy/devboards/db1x00/board_setup.c
delete mode 100644 arch/mips/alchemy/devboards/db1x00/platform.c
create mode 100644 arch/mips/alchemy/devboards/pb1100.c
delete mode 100644 arch/mips/alchemy/devboards/pb1100/Makefile
delete mode 100644 arch/mips/alchemy/devboards/pb1100/board_setup.c
delete mode 100644 arch/mips/alchemy/devboards/pb1100/platform.c
create mode 100644 arch/mips/alchemy/devboards/pb1200.c
delete mode 100644 arch/mips/alchemy/devboards/pb1200/Makefile
delete mode 100644 arch/mips/alchemy/devboards/pb1200/board_setup.c
delete mode 100644 arch/mips/alchemy/devboards/pb1200/platform.c
create mode 100644 arch/mips/alchemy/devboards/pb1500.c
delete mode 100644 arch/mips/alchemy/devboards/pb1500/Makefile
delete mode 100644 arch/mips/alchemy/devboards/pb1500/board_setup.c
delete mode 100644 arch/mips/alchemy/devboards/pb1500/platform.c
create mode 100644 arch/mips/alchemy/devboards/pb1550.c
delete mode 100644 arch/mips/alchemy/devboards/pb1550/Makefile
delete mode 100644 arch/mips/alchemy/devboards/pb1550/board_setup.c
delete mode 100644 arch/mips/alchemy/devboards/pb1550/platform.c
diff --git a/arch/mips/alchemy/devboards/Makefile b/arch/mips/alchemy/devboards/Makefile
index 3467ec9..f562852 100644
--- a/arch/mips/alchemy/devboards/Makefile
+++ b/arch/mips/alchemy/devboards/Makefile
@@ -4,13 +4,13 @@
obj-y += prom.o bcsr.o platform.o
obj-$(CONFIG_PM) += pm.o
-obj-$(CONFIG_MIPS_PB1100) += pb1100/
-obj-$(CONFIG_MIPS_PB1200) += pb1200/
-obj-$(CONFIG_MIPS_PB1500) += pb1500/
-obj-$(CONFIG_MIPS_PB1550) += pb1550/
-obj-$(CONFIG_MIPS_DB1000) += db1x00/
-obj-$(CONFIG_MIPS_DB1100) += db1x00/
-obj-$(CONFIG_MIPS_DB1200) += db1200/
+obj-$(CONFIG_MIPS_PB1100) += pb1100.o
+obj-$(CONFIG_MIPS_PB1200) += pb1200.o
+obj-$(CONFIG_MIPS_PB1500) += pb1500.o
+obj-$(CONFIG_MIPS_PB1550) += pb1550.o
+obj-$(CONFIG_MIPS_DB1000) += db1x00.o
+obj-$(CONFIG_MIPS_DB1100) += db1x00.o
+obj-$(CONFIG_MIPS_DB1200) += db1200.o
obj-$(CONFIG_MIPS_DB1300) += db1300.o
-obj-$(CONFIG_MIPS_DB1500) += db1x00/
+obj-$(CONFIG_MIPS_DB1500) += db1x00.o
obj-$(CONFIG_MIPS_DB1550) += db1550.o
diff --git a/arch/mips/alchemy/devboards/db1200.c b/arch/mips/alchemy/devboards/db1200.c
new file mode 100644
index 0000000..43f5f1b
--- /dev/null
+++ b/arch/mips/alchemy/devboards/db1200.c
@@ -0,0 +1,705 @@
+/*
+ * DBAu1200 board platform device registration
+ *
+ * Copyright (C) 2008-2011 Manuel Lauss
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/leds.h>
+#include <linux/mmc/host.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/platform_device.h>
+#include <linux/serial_8250.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#include <linux/smc91x.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1100_mmc.h>
+#include <asm/mach-au1x00/au1xxx_dbdma.h>
+#include <asm/mach-au1x00/au1550_spi.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <asm/mach-db1x00/db1200.h>
+
+#include "platform.h"
+
+
+const char *get_system_type(void)
+{
+ return "DB1200";
+}
+
+void __init board_setup(void)
+{
+ unsigned long freq0, clksrc, div, pfc;
+ unsigned short whoami;
+
+ bcsr_init(DB1200_BCSR_PHYS_ADDR,
+ DB1200_BCSR_PHYS_ADDR + DB1200_BCSR_HEXLED_OFS);
+
+ whoami = bcsr_read(BCSR_WHOAMI);
+ printk(KERN_INFO "Alchemy/AMD/RMI DB1200 Board, CPLD Rev %d"
+ " Board-ID %d Daughtercard ID %d\n",
+ (whoami >> 4) & 0xf, (whoami >> 8) & 0xf, whoami & 0xf);
+
+ /* SMBus/SPI on PSC0, Audio on PSC1 */
+ pfc = __raw_readl((void __iomem *)SYS_PINFUNC);
+ pfc &= ~(SYS_PINFUNC_P0A | SYS_PINFUNC_P0B);
+ pfc &= ~(SYS_PINFUNC_P1A | SYS_PINFUNC_P1B | SYS_PINFUNC_FS3);
+ pfc |= SYS_PINFUNC_P1C; /* SPI is configured later */
+ __raw_writel(pfc, (void __iomem *)SYS_PINFUNC);
+ wmb();
+
+ /* Clock configurations: PSC0: ~50MHz via Clkgen0, derived from
+ * CPU clock; all other clock generators off/unused.
+ */
+ div = (get_au1x00_speed() + 25000000) / 50000000;
+ if (div & 1)
+ div++;
+ div = ((div >> 1) - 1) & 0xff;
+
+ freq0 = div << SYS_FC_FRDIV0_BIT;
+ __raw_writel(freq0, (void __iomem *)SYS_FREQCTRL0);
+ wmb();
+ freq0 |= SYS_FC_FE0; /* enable F0 */
+ __raw_writel(freq0, (void __iomem *)SYS_FREQCTRL0);
+ wmb();
+
+ /* psc0_intclk comes 1:1 from F0 */
+ clksrc = SYS_CS_MUX_FQ0 << SYS_CS_ME0_BIT;
+ __raw_writel(clksrc, (void __iomem *)SYS_CLKSRC);
+ wmb();
+}
+
+/******************************************************************************/
+
+static struct mtd_partition db1200_spiflash_parts[] = {
+ {
+ .name = "DB1200 SPI flash",
+ .offset = 0,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct flash_platform_data db1200_spiflash_data = {
+ .name = "s25fl001",
+ .parts = db1200_spiflash_parts,
+ .nr_parts = ARRAY_SIZE(db1200_spiflash_parts),
+ .type = "m25p10",
+};
+
+static struct spi_board_info db1200_spi_devs[] __initdata = {
+ {
+ /* TI TMP121AIDBVR temp sensor */
+ .modalias = "tmp121",
+ .max_speed_hz = 2000000,
+ .bus_num = 0,
+ .chip_select = 0,
+ .mode = 0,
+ },
+ {
+ /* Spansion S25FL001D0FMA SPI flash */
+ .modalias = "m25p80",
+ .max_speed_hz = 50000000,
+ .bus_num = 0,
+ .chip_select = 1,
+ .mode = 0,
+ .platform_data = &db1200_spiflash_data,
+ },
+};
+
+static struct i2c_board_info db1200_i2c_devs[] __initdata = {
+ { I2C_BOARD_INFO("24c04", 0x52), }, /* AT24C04-10 I2C eeprom */
+ { I2C_BOARD_INFO("ne1619", 0x2d), }, /* adm1025-compat hwmon */
+ { I2C_BOARD_INFO("wm8731", 0x1b), }, /* I2S audio codec WM8731 */
+};
+
+/**********************************************************************/
+
+static void au1200_nand_cmd_ctrl(struct mtd_info *mtd, int cmd,
+ unsigned int ctrl)
+{
+ struct nand_chip *this = mtd->priv;
+ unsigned long ioaddr = (unsigned long)this->IO_ADDR_W;
+
+ ioaddr &= 0xffffff00;
+
+ if (ctrl & NAND_CLE) {
+ ioaddr += MEM_STNAND_CMD;
+ } else if (ctrl & NAND_ALE) {
+ ioaddr += MEM_STNAND_ADDR;
+ } else {
+ /* assume we want to r/w real data by default */
+ ioaddr += MEM_STNAND_DATA;
+ }
+ this->IO_ADDR_R = this->IO_ADDR_W = (void __iomem *)ioaddr;
+ if (cmd != NAND_CMD_NONE) {
+ __raw_writeb(cmd, this->IO_ADDR_W);
+ wmb();
+ }
+}
+
+static int au1200_nand_device_ready(struct mtd_info *mtd)
+{
+ return __raw_readl((void __iomem *)MEM_STSTAT) & 1;
+}
+
+static const char *db1200_part_probes[] = { "cmdlinepart", NULL };
+
+static struct mtd_partition db1200_nand_parts[] = {
+ {
+ .name = "NAND FS 0",
+ .offset = 0,
+ .size = 8 * 1024 * 1024,
+ },
+ {
+ .name = "NAND FS 1",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL
+ },
+};
+
+struct platform_nand_data db1200_nand_platdata = {
+ .chip = {
+ .nr_chips = 1,
+ .chip_offset = 0,
+ .nr_partitions = ARRAY_SIZE(db1200_nand_parts),
+ .partitions = db1200_nand_parts,
+ .chip_delay = 20,
+ .part_probe_types = db1200_part_probes,
+ },
+ .ctrl = {
+ .dev_ready = au1200_nand_device_ready,
+ .cmd_ctrl = au1200_nand_cmd_ctrl,
+ },
+};
+
+static struct resource db1200_nand_res[] = {
+ [0] = {
+ .start = DB1200_NAND_PHYS_ADDR,
+ .end = DB1200_NAND_PHYS_ADDR + 0xff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device db1200_nand_dev = {
+ .name = "gen_nand",
+ .num_resources = ARRAY_SIZE(db1200_nand_res),
+ .resource = db1200_nand_res,
+ .id = -1,
+ .dev = {
+ .platform_data = &db1200_nand_platdata,
+ }
+};
+
+/**********************************************************************/
+
+static struct smc91x_platdata db1200_eth_data = {
+ .flags = SMC91X_NOWAIT | SMC91X_USE_16BIT,
+ .leda = RPC_LED_100_10,
+ .ledb = RPC_LED_TX_RX,
+};
+
+static struct resource db1200_eth_res[] = {
+ [0] = {
+ .start = DB1200_ETH_PHYS_ADDR,
+ .end = DB1200_ETH_PHYS_ADDR + 0xf,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = DB1200_ETH_INT,
+ .end = DB1200_ETH_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device db1200_eth_dev = {
+ .dev = {
+ .platform_data = &db1200_eth_data,
+ },
+ .name = "smc91x",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(db1200_eth_res),
+ .resource = db1200_eth_res,
+};
+
+/**********************************************************************/
+
+static struct resource db1200_ide_res[] = {
+ [0] = {
+ .start = DB1200_IDE_PHYS_ADDR,
+ .end = DB1200_IDE_PHYS_ADDR + DB1200_IDE_PHYS_LEN - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = DB1200_IDE_INT,
+ .end = DB1200_IDE_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1200_DSCR_CMD0_DMA_REQ1,
+ .end = AU1200_DSCR_CMD0_DMA_REQ1,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static u64 au1200_ide_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device db1200_ide_dev = {
+ .name = "au1200-ide",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1200_ide_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .num_resources = ARRAY_SIZE(db1200_ide_res),
+ .resource = db1200_ide_res,
+};
+
+/**********************************************************************/
+
+static struct platform_device db1200_rtc_dev = {
+ .name = "rtc-au1xxx",
+ .id = -1,
+};
+
+/**********************************************************************/
+
+/* SD carddetects: they're supposed to be edge-triggered, but ack
+ * doesn't seem to work (CPLD Rev 2). Instead, the screaming one
+ * is disabled and its counterpart enabled. The 500ms timeout is
+ * because the carddetect isn't debounced in hardware.
+ */
+static irqreturn_t db1200_mmc_cd(int irq, void *ptr)
+{
+ void(*mmc_cd)(struct mmc_host *, unsigned long);
+
+ if (irq == DB1200_SD0_INSERT_INT) {
+ disable_irq_nosync(DB1200_SD0_INSERT_INT);
+ enable_irq(DB1200_SD0_EJECT_INT);
+ } else {
+ disable_irq_nosync(DB1200_SD0_EJECT_INT);
+ enable_irq(DB1200_SD0_INSERT_INT);
+ }
+
+ /* link against CONFIG_MMC=m */
+ mmc_cd = symbol_get(mmc_detect_change);
+ if (mmc_cd) {
+ mmc_cd(ptr, msecs_to_jiffies(500));
+ symbol_put(mmc_detect_change);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static int db1200_mmc_cd_setup(void *mmc_host, int en)
+{
+ int ret;
+
+ if (en) {
+ ret = request_irq(DB1200_SD0_INSERT_INT, db1200_mmc_cd,
+ IRQF_DISABLED, "sd_insert", mmc_host);
+ if (ret)
+ goto out;
+
+ ret = request_irq(DB1200_SD0_EJECT_INT, db1200_mmc_cd,
+ IRQF_DISABLED, "sd_eject", mmc_host);
+ if (ret) {
+ free_irq(DB1200_SD0_INSERT_INT, mmc_host);
+ goto out;
+ }
+
+ if (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD0INSERT)
+ enable_irq(DB1200_SD0_EJECT_INT);
+ else
+ enable_irq(DB1200_SD0_INSERT_INT);
+
+ } else {
+ free_irq(DB1200_SD0_INSERT_INT, mmc_host);
+ free_irq(DB1200_SD0_EJECT_INT, mmc_host);
+ }
+ ret = 0;
+out:
+ return ret;
+}
+
+static void db1200_mmc_set_power(void *mmc_host, int state)
+{
+ if (state) {
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD0PWR);
+ msleep(400); /* stabilization time */
+ } else
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD0PWR, 0);
+}
+
+static int db1200_mmc_card_readonly(void *mmc_host)
+{
+ return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD0WP) ? 1 : 0;
+}
+
+static int db1200_mmc_card_inserted(void *mmc_host)
+{
+ return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD0INSERT) ? 1 : 0;
+}
+
+static void db1200_mmcled_set(struct led_classdev *led,
+ enum led_brightness brightness)
+{
+ if (brightness != LED_OFF)
+ bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED0, 0);
+ else
+ bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED0);
+}
+
+static struct led_classdev db1200_mmc_led = {
+ .brightness_set = db1200_mmcled_set,
+};
+
+static struct au1xmmc_platform_data db1200mmc_platdata = {
+ .cd_setup = db1200_mmc_cd_setup,
+ .set_power = db1200_mmc_set_power,
+ .card_inserted = db1200_mmc_card_inserted,
+ .card_readonly = db1200_mmc_card_readonly,
+ .led = &db1200_mmc_led,
+};
+
+static struct resource au1200_mmc0_resources[] = {
+ [0] = {
+ .start = AU1100_SD0_PHYS_ADDR,
+ .end = AU1100_SD0_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_SD_INT,
+ .end = AU1200_SD_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1200_DSCR_CMD0_SDMS_TX0,
+ .end = AU1200_DSCR_CMD0_SDMS_TX0,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1200_DSCR_CMD0_SDMS_RX0,
+ .end = AU1200_DSCR_CMD0_SDMS_RX0,
+ .flags = IORESOURCE_DMA,
+ }
+};
+
+static u64 au1xxx_mmc_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device db1200_mmc0_dev = {
+ .name = "au1xxx-mmc",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1xxx_mmc_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &db1200mmc_platdata,
+ },
+ .num_resources = ARRAY_SIZE(au1200_mmc0_resources),
+ .resource = au1200_mmc0_resources,
+};
+
+/**********************************************************************/
+
+static struct resource au1200_lcd_res[] = {
+ [0] = {
+ .start = AU1200_LCD_PHYS_ADDR,
+ .end = AU1200_LCD_PHYS_ADDR + 0x800 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_LCD_INT,
+ .end = AU1200_LCD_INT,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static u64 au1200_lcd_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device au1200_lcd_dev = {
+ .name = "au1200-lcd",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1200_lcd_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .num_resources = ARRAY_SIZE(au1200_lcd_res),
+ .resource = au1200_lcd_res,
+};
+
+/**********************************************************************/
+
+static struct resource au1200_psc0_res[] = {
+ [0] = {
+ .start = AU1550_PSC0_PHYS_ADDR,
+ .end = AU1550_PSC0_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_PSC0_INT,
+ .end = AU1200_PSC0_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1200_DSCR_CMD0_PSC0_TX,
+ .end = AU1200_DSCR_CMD0_PSC0_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1200_DSCR_CMD0_PSC0_RX,
+ .end = AU1200_DSCR_CMD0_PSC0_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device db1200_i2c_dev = {
+ .name = "au1xpsc_smbus",
+ .id = 0, /* bus number */
+ .num_resources = ARRAY_SIZE(au1200_psc0_res),
+ .resource = au1200_psc0_res,
+};
+
+static void db1200_spi_cs_en(struct au1550_spi_info *spi, int cs, int pol)
+{
+ if (cs)
+ bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_SPISEL);
+ else
+ bcsr_mod(BCSR_RESETS, BCSR_RESETS_SPISEL, 0);
+}
+
+static struct au1550_spi_info db1200_spi_platdata = {
+ .mainclk_hz = 50000000, /* PSC0 clock */
+ .num_chipselect = 2,
+ .activate_cs = db1200_spi_cs_en,
+};
+
+static u64 spi_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device db1200_spi_dev = {
+ .dev = {
+ .dma_mask = &spi_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &db1200_spi_platdata,
+ },
+ .name = "au1550-spi",
+ .id = 0, /* bus number */
+ .num_resources = ARRAY_SIZE(au1200_psc0_res),
+ .resource = au1200_psc0_res,
+};
+
+static struct resource au1200_psc1_res[] = {
+ [0] = {
+ .start = AU1550_PSC1_PHYS_ADDR,
+ .end = AU1550_PSC1_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_PSC1_INT,
+ .end = AU1200_PSC1_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1200_DSCR_CMD0_PSC1_TX,
+ .end = AU1200_DSCR_CMD0_PSC1_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1200_DSCR_CMD0_PSC1_RX,
+ .end = AU1200_DSCR_CMD0_PSC1_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+/* AC97 or I2S device */
+static struct platform_device db1200_audio_dev = {
+ /* name assigned later based on switch setting */
+ .id = 1, /* PSC ID */
+ .num_resources = ARRAY_SIZE(au1200_psc1_res),
+ .resource = au1200_psc1_res,
+};
+
+/* DB1200 ASoC card device */
+static struct platform_device db1200_sound_dev = {
+ /* name assigned later based on switch setting */
+ .id = 1, /* PSC ID */
+};
+
+static struct platform_device db1200_stac_dev = {
+ .name = "ac97-codec",
+ .id = 1, /* on PSC1 */
+};
+
+static struct platform_device db1200_audiodma_dev = {
+ .name = "au1xpsc-pcm",
+ .id = 1, /* PSC ID */
+};
+
+static struct platform_device *db1200_devs[] __initdata = {
+ NULL, /* PSC0, selected by S6.8 */
+ &db1200_ide_dev,
+ &db1200_mmc0_dev,
+ &au1200_lcd_dev,
+ &db1200_eth_dev,
+ &db1200_rtc_dev,
+ &db1200_nand_dev,
+ &db1200_audiodma_dev,
+ &db1200_audio_dev,
+ &db1200_stac_dev,
+ &db1200_sound_dev,
+};
+
+static int __init db1200_dev_init(void)
+{
+ unsigned long pfc;
+ unsigned short sw;
+ int swapped;
+
+ /* GPIO7 is low-level triggered CPLD cascade */
+ irq_set_irq_type(AU1200_GPIO7_INT, IRQF_TRIGGER_LOW);
+ bcsr_init_irq(DB1200_INT_BEGIN, DB1200_INT_END, AU1200_GPIO7_INT);
+
+ /* insert/eject pairs: one of both is always screaming. To avoid
+ * issues they must not be automatically enabled when initially
+ * requested.
+ */
+ irq_set_status_flags(DB1200_SD0_INSERT_INT, IRQ_NOAUTOEN);
+ irq_set_status_flags(DB1200_SD0_EJECT_INT, IRQ_NOAUTOEN);
+ irq_set_status_flags(DB1200_PC0_INSERT_INT, IRQ_NOAUTOEN);
+ irq_set_status_flags(DB1200_PC0_EJECT_INT, IRQ_NOAUTOEN);
+ irq_set_status_flags(DB1200_PC1_INSERT_INT, IRQ_NOAUTOEN);
+ irq_set_status_flags(DB1200_PC1_EJECT_INT, IRQ_NOAUTOEN);
+
+ i2c_register_board_info(0, db1200_i2c_devs,
+ ARRAY_SIZE(db1200_i2c_devs));
+ spi_register_board_info(db1200_spi_devs,
+ ARRAY_SIZE(db1200_i2c_devs));
+
+ /* SWITCHES: S6.8 I2C/SPI selector (OFF=I2C ON=SPI)
+ * S6.7 AC97/I2S selector (OFF=AC97 ON=I2S)
+ */
+
+ /* NOTE: GPIO215 controls OTG VBUS supply. In SPI mode however
+ * this pin is claimed by PSC0 (unused though, but pinmux doesn't
+ * allow to free it without crippling the SPI interface).
+ * As a result, in SPI mode, OTG simply won't work (PSC0 uses
+ * it as an input pin which is pulled high on the boards).
+ */
+ pfc = __raw_readl((void __iomem *)SYS_PINFUNC) & ~SYS_PINFUNC_P0A;
+
+ /* switch off OTG VBUS supply */
+ gpio_request(215, "otg-vbus");
+ gpio_direction_output(215, 1);
+
+ printk(KERN_INFO "DB1200 device configuration:\n");
+
+ sw = bcsr_read(BCSR_SWITCHES);
+ if (sw & BCSR_SWITCHES_DIP_8) {
+ db1200_devs[0] = &db1200_i2c_dev;
+ bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
+
+ pfc |= (2 << 17); /* GPIO2 block owns GPIO215 */
+
+ printk(KERN_INFO " S6.8 OFF: PSC0 mode I2C\n");
+ printk(KERN_INFO " OTG port VBUS supply available!\n");
+ } else {
+ db1200_devs[0] = &db1200_spi_dev;
+ bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_PSC0MUX);
+
+ pfc |= (1 << 17); /* PSC0 owns GPIO215 */
+
+ printk(KERN_INFO " S6.8 ON : PSC0 mode SPI\n");
+ printk(KERN_INFO " OTG port VBUS supply disabled\n");
+ }
+ __raw_writel(pfc, (void __iomem *)SYS_PINFUNC);
+ wmb();
+
+ /* Audio: DIP7 selects I2S(0)/AC97(1), but need I2C for I2S!
+ * so: DIP7=1 || DIP8=0 => AC97, DIP7=0 && DIP8=1 => I2S
+ */
+ sw &= BCSR_SWITCHES_DIP_8 | BCSR_SWITCHES_DIP_7;
+ if (sw == BCSR_SWITCHES_DIP_8) {
+ bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_PSC1MUX);
+ db1200_audio_dev.name = "au1xpsc_i2s";
+ db1200_sound_dev.name = "db1200-i2s";
+ printk(KERN_INFO " S6.7 ON : PSC1 mode I2S\n");
+ } else {
+ bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC1MUX, 0);
+ db1200_audio_dev.name = "au1xpsc_ac97";
+ db1200_sound_dev.name = "db1200-ac97";
+ printk(KERN_INFO " S6.7 OFF: PSC1 mode AC97\n");
+ }
+
+ /* Audio PSC clock is supplied externally. (FIXME: platdata!!) */
+ __raw_writel(PSC_SEL_CLK_SERCLK,
+ (void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR) + PSC_SEL_OFFSET);
+ wmb();
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ DB1200_PC0_INT, DB1200_PC0_INSERT_INT,
+ /*DB1200_PC0_STSCHG_INT*/0, DB1200_PC0_EJECT_INT, 0);
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x004010000 - 1,
+ DB1200_PC1_INT, DB1200_PC1_INSERT_INT,
+ /*DB1200_PC1_STSCHG_INT*/0, DB1200_PC1_EJECT_INT, 1);
+
+ swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1200_SWAPBOOT;
+ db1x_register_norflash(64 << 20, 2, swapped);
+
+ return platform_add_devices(db1200_devs, ARRAY_SIZE(db1200_devs));
+}
+device_initcall(db1200_dev_init);
+
+/* au1200fb calls these: STERBT EINEN TRAGISCHEN TOD!!! */
+int board_au1200fb_panel(void)
+{
+ return (bcsr_read(BCSR_SWITCHES) >> 8) & 0x0f;
+}
+
+int board_au1200fb_panel_init(void)
+{
+ /* Apply power */
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+ BCSR_BOARD_LCDBL);
+ return 0;
+}
+
+int board_au1200fb_panel_shutdown(void)
+{
+ /* Remove power */
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+ BCSR_BOARD_LCDBL, 0);
+ return 0;
+}
diff --git a/arch/mips/alchemy/devboards/db1200/Makefile b/arch/mips/alchemy/devboards/db1200/Makefile
deleted file mode 100644
index 17840a5..0000000
--- a/arch/mips/alchemy/devboards/db1200/Makefile
+++ /dev/null
@@ -1 +0,0 @@
-obj-y += setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/db1200/platform.c b/arch/mips/alchemy/devboards/db1200/platform.c
deleted file mode 100644
index c61867c..0000000
--- a/arch/mips/alchemy/devboards/db1200/platform.c
+++ /dev/null
@@ -1,648 +0,0 @@
-/*
- * DBAu1200 board platform device registration
- *
- * Copyright (C) 2008-2009 Manuel Lauss
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/dma-mapping.h>
-#include <linux/gpio.h>
-#include <linux/i2c.h>
-#include <linux/init.h>
-#include <linux/io.h>
-#include <linux/leds.h>
-#include <linux/mmc/host.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/nand.h>
-#include <linux/mtd/partitions.h>
-#include <linux/platform_device.h>
-#include <linux/serial_8250.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/flash.h>
-#include <linux/smc91x.h>
-
-#include <asm/mach-au1x00/au1100_mmc.h>
-#include <asm/mach-au1x00/au1xxx_dbdma.h>
-#include <asm/mach-au1x00/au1550_spi.h>
-#include <asm/mach-db1x00/bcsr.h>
-#include <asm/mach-db1x00/db1200.h>
-
-#include "../platform.h"
-
-static struct mtd_partition db1200_spiflash_parts[] = {
- {
- .name = "DB1200 SPI flash",
- .offset = 0,
- .size = MTDPART_SIZ_FULL,
- },
-};
-
-static struct flash_platform_data db1200_spiflash_data = {
- .name = "s25fl001",
- .parts = db1200_spiflash_parts,
- .nr_parts = ARRAY_SIZE(db1200_spiflash_parts),
- .type = "m25p10",
-};
-
-static struct spi_board_info db1200_spi_devs[] __initdata = {
- {
- /* TI TMP121AIDBVR temp sensor */
- .modalias = "tmp121",
- .max_speed_hz = 2000000,
- .bus_num = 0,
- .chip_select = 0,
- .mode = 0,
- },
- {
- /* Spansion S25FL001D0FMA SPI flash */
- .modalias = "m25p80",
- .max_speed_hz = 50000000,
- .bus_num = 0,
- .chip_select = 1,
- .mode = 0,
- .platform_data = &db1200_spiflash_data,
- },
-};
-
-static struct i2c_board_info db1200_i2c_devs[] __initdata = {
- {
- /* AT24C04-10 I2C eeprom */
- I2C_BOARD_INFO("24c04", 0x52),
- },
- {
- /* Philips NE1619 temp/voltage sensor (adm1025 drv) */
- I2C_BOARD_INFO("ne1619", 0x2d),
- },
- {
- /* I2S audio codec WM8731 */
- I2C_BOARD_INFO("wm8731", 0x1b),
- },
-};
-
-/**********************************************************************/
-
-static void au1200_nand_cmd_ctrl(struct mtd_info *mtd, int cmd,
- unsigned int ctrl)
-{
- struct nand_chip *this = mtd->priv;
- unsigned long ioaddr = (unsigned long)this->IO_ADDR_W;
-
- ioaddr &= 0xffffff00;
-
- if (ctrl & NAND_CLE) {
- ioaddr += MEM_STNAND_CMD;
- } else if (ctrl & NAND_ALE) {
- ioaddr += MEM_STNAND_ADDR;
- } else {
- /* assume we want to r/w real data by default */
- ioaddr += MEM_STNAND_DATA;
- }
- this->IO_ADDR_R = this->IO_ADDR_W = (void __iomem *)ioaddr;
- if (cmd != NAND_CMD_NONE) {
- __raw_writeb(cmd, this->IO_ADDR_W);
- wmb();
- }
-}
-
-static int au1200_nand_device_ready(struct mtd_info *mtd)
-{
- return __raw_readl((void __iomem *)MEM_STSTAT) & 1;
-}
-
-static const char *db1200_part_probes[] = { "cmdlinepart", NULL };
-
-static struct mtd_partition db1200_nand_parts[] = {
- {
- .name = "NAND FS 0",
- .offset = 0,
- .size = 8 * 1024 * 1024,
- },
- {
- .name = "NAND FS 1",
- .offset = MTDPART_OFS_APPEND,
- .size = MTDPART_SIZ_FULL
- },
-};
-
-struct platform_nand_data db1200_nand_platdata = {
- .chip = {
- .nr_chips = 1,
- .chip_offset = 0,
- .nr_partitions = ARRAY_SIZE(db1200_nand_parts),
- .partitions = db1200_nand_parts,
- .chip_delay = 20,
- .part_probe_types = db1200_part_probes,
- },
- .ctrl = {
- .dev_ready = au1200_nand_device_ready,
- .cmd_ctrl = au1200_nand_cmd_ctrl,
- },
-};
-
-static struct resource db1200_nand_res[] = {
- [0] = {
- .start = DB1200_NAND_PHYS_ADDR,
- .end = DB1200_NAND_PHYS_ADDR + 0xff,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct platform_device db1200_nand_dev = {
- .name = "gen_nand",
- .num_resources = ARRAY_SIZE(db1200_nand_res),
- .resource = db1200_nand_res,
- .id = -1,
- .dev = {
- .platform_data = &db1200_nand_platdata,
- }
-};
-
-/**********************************************************************/
-
-static struct smc91x_platdata db1200_eth_data = {
- .flags = SMC91X_NOWAIT | SMC91X_USE_16BIT,
- .leda = RPC_LED_100_10,
- .ledb = RPC_LED_TX_RX,
-};
-
-static struct resource db1200_eth_res[] = {
- [0] = {
- .start = DB1200_ETH_PHYS_ADDR,
- .end = DB1200_ETH_PHYS_ADDR + 0xf,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = DB1200_ETH_INT,
- .end = DB1200_ETH_INT,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device db1200_eth_dev = {
- .dev = {
- .platform_data = &db1200_eth_data,
- },
- .name = "smc91x",
- .id = -1,
- .num_resources = ARRAY_SIZE(db1200_eth_res),
- .resource = db1200_eth_res,
-};
-
-/**********************************************************************/
-
-static struct resource db1200_ide_res[] = {
- [0] = {
- .start = DB1200_IDE_PHYS_ADDR,
- .end = DB1200_IDE_PHYS_ADDR + DB1200_IDE_PHYS_LEN - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = DB1200_IDE_INT,
- .end = DB1200_IDE_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_DMA_REQ1,
- .end = AU1200_DSCR_CMD0_DMA_REQ1,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static u64 ide_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device db1200_ide_dev = {
- .name = "au1200-ide",
- .id = 0,
- .dev = {
- .dma_mask = &ide_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(db1200_ide_res),
- .resource = db1200_ide_res,
-};
-
-/**********************************************************************/
-
-static struct platform_device db1200_rtc_dev = {
- .name = "rtc-au1xxx",
- .id = -1,
-};
-
-/**********************************************************************/
-
-/* SD carddetects: they're supposed to be edge-triggered, but ack
- * doesn't seem to work (CPLD Rev 2). Instead, the screaming one
- * is disabled and its counterpart enabled. The 500ms timeout is
- * because the carddetect isn't debounced in hardware.
- */
-static irqreturn_t db1200_mmc_cd(int irq, void *ptr)
-{
- void(*mmc_cd)(struct mmc_host *, unsigned long);
-
- if (irq == DB1200_SD0_INSERT_INT) {
- disable_irq_nosync(DB1200_SD0_INSERT_INT);
- enable_irq(DB1200_SD0_EJECT_INT);
- } else {
- disable_irq_nosync(DB1200_SD0_EJECT_INT);
- enable_irq(DB1200_SD0_INSERT_INT);
- }
-
- /* link against CONFIG_MMC=m */
- mmc_cd = symbol_get(mmc_detect_change);
- if (mmc_cd) {
- mmc_cd(ptr, msecs_to_jiffies(500));
- symbol_put(mmc_detect_change);
- }
-
- return IRQ_HANDLED;
-}
-
-static int db1200_mmc_cd_setup(void *mmc_host, int en)
-{
- int ret;
-
- if (en) {
- ret = request_irq(DB1200_SD0_INSERT_INT, db1200_mmc_cd,
- IRQF_DISABLED, "sd_insert", mmc_host);
- if (ret)
- goto out;
-
- ret = request_irq(DB1200_SD0_EJECT_INT, db1200_mmc_cd,
- IRQF_DISABLED, "sd_eject", mmc_host);
- if (ret) {
- free_irq(DB1200_SD0_INSERT_INT, mmc_host);
- goto out;
- }
-
- if (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD0INSERT)
- enable_irq(DB1200_SD0_EJECT_INT);
- else
- enable_irq(DB1200_SD0_INSERT_INT);
-
- } else {
- free_irq(DB1200_SD0_INSERT_INT, mmc_host);
- free_irq(DB1200_SD0_EJECT_INT, mmc_host);
- }
- ret = 0;
-out:
- return ret;
-}
-
-static void db1200_mmc_set_power(void *mmc_host, int state)
-{
- if (state) {
- bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD0PWR);
- msleep(400); /* stabilization time */
- } else
- bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD0PWR, 0);
-}
-
-static int db1200_mmc_card_readonly(void *mmc_host)
-{
- return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD0WP) ? 1 : 0;
-}
-
-static int db1200_mmc_card_inserted(void *mmc_host)
-{
- return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD0INSERT) ? 1 : 0;
-}
-
-static void db1200_mmcled_set(struct led_classdev *led,
- enum led_brightness brightness)
-{
- if (brightness != LED_OFF)
- bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED0, 0);
- else
- bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED0);
-}
-
-static struct led_classdev db1200_mmc_led = {
- .brightness_set = db1200_mmcled_set,
-};
-
-static struct au1xmmc_platform_data db1200mmc_platdata = {
- .cd_setup = db1200_mmc_cd_setup,
- .set_power = db1200_mmc_set_power,
- .card_inserted = db1200_mmc_card_inserted,
- .card_readonly = db1200_mmc_card_readonly,
- .led = &db1200_mmc_led,
-};
-
-static struct resource au1200_mmc0_resources[] = {
- [0] = {
- .start = AU1100_SD0_PHYS_ADDR,
- .end = AU1100_SD0_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_SD_INT,
- .end = AU1200_SD_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_SDMS_TX0,
- .end = AU1200_DSCR_CMD0_SDMS_TX0,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = AU1200_DSCR_CMD0_SDMS_RX0,
- .end = AU1200_DSCR_CMD0_SDMS_RX0,
- .flags = IORESOURCE_DMA,
- }
-};
-
-static u64 au1xxx_mmc_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device db1200_mmc0_dev = {
- .name = "au1xxx-mmc",
- .id = 0,
- .dev = {
- .dma_mask = &au1xxx_mmc_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &db1200mmc_platdata,
- },
- .num_resources = ARRAY_SIZE(au1200_mmc0_resources),
- .resource = au1200_mmc0_resources,
-};
-
-/**********************************************************************/
-
-static struct resource au1200_lcd_res[] = {
- [0] = {
- .start = AU1200_LCD_PHYS_ADDR,
- .end = AU1200_LCD_PHYS_ADDR + 0x800 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_LCD_INT,
- .end = AU1200_LCD_INT,
- .flags = IORESOURCE_IRQ,
- }
-};
-
-static u64 au1200_lcd_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device au1200_lcd_dev = {
- .name = "au1200-lcd",
- .id = 0,
- .dev = {
- .dma_mask = &au1200_lcd_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(au1200_lcd_res),
- .resource = au1200_lcd_res,
-};
-
-/**********************************************************************/
-
-static struct resource au1200_psc0_res[] = {
- [0] = {
- .start = AU1550_PSC0_PHYS_ADDR,
- .end = AU1550_PSC0_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_PSC0_INT,
- .end = AU1200_PSC0_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_PSC0_TX,
- .end = AU1200_DSCR_CMD0_PSC0_TX,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = AU1200_DSCR_CMD0_PSC0_RX,
- .end = AU1200_DSCR_CMD0_PSC0_RX,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static struct platform_device db1200_i2c_dev = {
- .name = "au1xpsc_smbus",
- .id = 0, /* bus number */
- .num_resources = ARRAY_SIZE(au1200_psc0_res),
- .resource = au1200_psc0_res,
-};
-
-static void db1200_spi_cs_en(struct au1550_spi_info *spi, int cs, int pol)
-{
- if (cs)
- bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_SPISEL);
- else
- bcsr_mod(BCSR_RESETS, BCSR_RESETS_SPISEL, 0);
-}
-
-static struct au1550_spi_info db1200_spi_platdata = {
- .mainclk_hz = 50000000, /* PSC0 clock */
- .num_chipselect = 2,
- .activate_cs = db1200_spi_cs_en,
-};
-
-static u64 spi_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device db1200_spi_dev = {
- .dev = {
- .dma_mask = &spi_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &db1200_spi_platdata,
- },
- .name = "au1550-spi",
- .id = 0, /* bus number */
- .num_resources = ARRAY_SIZE(au1200_psc0_res),
- .resource = au1200_psc0_res,
-};
-
-static struct resource au1200_psc1_res[] = {
- [0] = {
- .start = AU1550_PSC1_PHYS_ADDR,
- .end = AU1550_PSC1_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_PSC1_INT,
- .end = AU1200_PSC1_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_PSC1_TX,
- .end = AU1200_DSCR_CMD0_PSC1_TX,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = AU1200_DSCR_CMD0_PSC1_RX,
- .end = AU1200_DSCR_CMD0_PSC1_RX,
- .flags = IORESOURCE_DMA,
- },
-};
-
-/* AC97 or I2S device */
-static struct platform_device db1200_audio_dev = {
- /* name assigned later based on switch setting */
- .id = 1, /* PSC ID */
- .num_resources = ARRAY_SIZE(au1200_psc1_res),
- .resource = au1200_psc1_res,
-};
-
-/* DB1200 ASoC card device */
-static struct platform_device db1200_sound_dev = {
- /* name assigned later based on switch setting */
- .id = 1, /* PSC ID */
-};
-
-static struct platform_device db1200_stac_dev = {
- .name = "ac97-codec",
- .id = 1, /* on PSC1 */
-};
-
-static struct platform_device db1200_audiodma_dev = {
- .name = "au1xpsc-pcm",
- .id = 1, /* PSC ID */
-};
-
-static struct platform_device *db1200_devs[] __initdata = {
- NULL, /* PSC0, selected by S6.8 */
- &db1200_ide_dev,
- &db1200_mmc0_dev,
- &au1200_lcd_dev,
- &db1200_eth_dev,
- &db1200_rtc_dev,
- &db1200_nand_dev,
- &db1200_audiodma_dev,
- &db1200_audio_dev,
- &db1200_stac_dev,
- &db1200_sound_dev,
-};
-
-static int __init db1200_dev_init(void)
-{
- unsigned long pfc;
- unsigned short sw;
- int swapped;
-
- i2c_register_board_info(0, db1200_i2c_devs,
- ARRAY_SIZE(db1200_i2c_devs));
- spi_register_board_info(db1200_spi_devs,
- ARRAY_SIZE(db1200_i2c_devs));
-
- /* SWITCHES: S6.8 I2C/SPI selector (OFF=I2C ON=SPI)
- * S6.7 AC97/I2S selector (OFF=AC97 ON=I2S)
- */
-
- /* NOTE: GPIO215 controls OTG VBUS supply. In SPI mode however
- * this pin is claimed by PSC0 (unused though, but pinmux doesn't
- * allow to free it without crippling the SPI interface).
- * As a result, in SPI mode, OTG simply won't work (PSC0 uses
- * it as an input pin which is pulled high on the boards).
- */
- pfc = __raw_readl((void __iomem *)SYS_PINFUNC) & ~SYS_PINFUNC_P0A;
-
- /* switch off OTG VBUS supply */
- gpio_request(215, "otg-vbus");
- gpio_direction_output(215, 1);
-
- printk(KERN_INFO "DB1200 device configuration:\n");
-
- sw = bcsr_read(BCSR_SWITCHES);
- if (sw & BCSR_SWITCHES_DIP_8) {
- db1200_devs[0] = &db1200_i2c_dev;
- bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
-
- pfc |= (2 << 17); /* GPIO2 block owns GPIO215 */
-
- printk(KERN_INFO " S6.8 OFF: PSC0 mode I2C\n");
- printk(KERN_INFO " OTG port VBUS supply available!\n");
- } else {
- db1200_devs[0] = &db1200_spi_dev;
- bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_PSC0MUX);
-
- pfc |= (1 << 17); /* PSC0 owns GPIO215 */
-
- printk(KERN_INFO " S6.8 ON : PSC0 mode SPI\n");
- printk(KERN_INFO " OTG port VBUS supply disabled\n");
- }
- __raw_writel(pfc, (void __iomem *)SYS_PINFUNC);
- wmb();
-
- /* Audio: DIP7 selects I2S(0)/AC97(1), but need I2C for I2S!
- * so: DIP7=1 || DIP8=0 => AC97, DIP7=0 && DIP8=1 => I2S
- */
- sw &= BCSR_SWITCHES_DIP_8 | BCSR_SWITCHES_DIP_7;
- if (sw == BCSR_SWITCHES_DIP_8) {
- bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_PSC1MUX);
- db1200_audio_dev.name = "au1xpsc_i2s";
- db1200_sound_dev.name = "db1200-i2s";
- printk(KERN_INFO " S6.7 ON : PSC1 mode I2S\n");
- } else {
- bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC1MUX, 0);
- db1200_audio_dev.name = "au1xpsc_ac97";
- db1200_sound_dev.name = "db1200-ac97";
- printk(KERN_INFO " S6.7 OFF: PSC1 mode AC97\n");
- }
-
- /* Audio PSC clock is supplied externally. (FIXME: platdata!!) */
- __raw_writel(PSC_SEL_CLK_SERCLK,
- (void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR) + PSC_SEL_OFFSET);
- wmb();
-
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
- DB1200_PC0_INT, DB1200_PC0_INSERT_INT,
- /*DB1200_PC0_STSCHG_INT*/0, DB1200_PC0_EJECT_INT, 0);
-
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004000000,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x004000000,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x004010000 - 1,
- DB1200_PC1_INT, DB1200_PC1_INSERT_INT,
- /*DB1200_PC1_STSCHG_INT*/0, DB1200_PC1_EJECT_INT, 1);
-
- swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1200_SWAPBOOT;
- db1x_register_norflash(64 << 20, 2, swapped);
-
- return platform_add_devices(db1200_devs, ARRAY_SIZE(db1200_devs));
-}
-device_initcall(db1200_dev_init);
-
-/* au1200fb calls these: STERBT EINEN TRAGISCHEN TOD!!! */
-int board_au1200fb_panel(void)
-{
- return (bcsr_read(BCSR_SWITCHES) >> 8) & 0x0f;
-}
-
-int board_au1200fb_panel_init(void)
-{
- /* Apply power */
- bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
- BCSR_BOARD_LCDBL);
- return 0;
-}
-
-int board_au1200fb_panel_shutdown(void)
-{
- /* Remove power */
- bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
- BCSR_BOARD_LCDBL, 0);
- return 0;
-}
diff --git a/arch/mips/alchemy/devboards/db1200/setup.c b/arch/mips/alchemy/devboards/db1200/setup.c
deleted file mode 100644
index 4a89800..0000000
--- a/arch/mips/alchemy/devboards/db1200/setup.c
+++ /dev/null
@@ -1,81 +0,0 @@
-/*
- * Alchemy/AMD/RMI DB1200 board setup.
- *
- * Licensed under the terms outlined in the file COPYING in the root of
- * this source archive.
- */
-
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/io.h>
-#include <linux/kernel.h>
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-db1x00/bcsr.h>
-#include <asm/mach-db1x00/db1200.h>
-
-const char *get_system_type(void)
-{
- return "Alchemy Db1200";
-}
-
-void __init board_setup(void)
-{
- unsigned long freq0, clksrc, div, pfc;
- unsigned short whoami;
-
- bcsr_init(DB1200_BCSR_PHYS_ADDR,
- DB1200_BCSR_PHYS_ADDR + DB1200_BCSR_HEXLED_OFS);
-
- whoami = bcsr_read(BCSR_WHOAMI);
- printk(KERN_INFO "Alchemy/AMD/RMI DB1200 Board, CPLD Rev %d"
- " Board-ID %d Daughtercard ID %d\n",
- (whoami >> 4) & 0xf, (whoami >> 8) & 0xf, whoami & 0xf);
-
- /* SMBus/SPI on PSC0, Audio on PSC1 */
- pfc = __raw_readl((void __iomem *)SYS_PINFUNC);
- pfc &= ~(SYS_PINFUNC_P0A | SYS_PINFUNC_P0B);
- pfc &= ~(SYS_PINFUNC_P1A | SYS_PINFUNC_P1B | SYS_PINFUNC_FS3);
- pfc |= SYS_PINFUNC_P1C; /* SPI is configured later */
- __raw_writel(pfc, (void __iomem *)SYS_PINFUNC);
- wmb();
-
- /* Clock configurations: PSC0: ~50MHz via Clkgen0, derived from
- * CPU clock; all other clock generators off/unused.
- */
- div = (get_au1x00_speed() + 25000000) / 50000000;
- if (div & 1)
- div++;
- div = ((div >> 1) - 1) & 0xff;
-
- freq0 = div << SYS_FC_FRDIV0_BIT;
- __raw_writel(freq0, (void __iomem *)SYS_FREQCTRL0);
- wmb();
- freq0 |= SYS_FC_FE0; /* enable F0 */
- __raw_writel(freq0, (void __iomem *)SYS_FREQCTRL0);
- wmb();
-
- /* psc0_intclk comes 1:1 from F0 */
- clksrc = SYS_CS_MUX_FQ0 << SYS_CS_ME0_BIT;
- __raw_writel(clksrc, (void __iomem *)SYS_CLKSRC);
- wmb();
-}
-
-static int __init db1200_arch_init(void)
-{
- /* GPIO7 is low-level triggered CPLD cascade */
- irq_set_irq_type(AU1200_GPIO7_INT, IRQF_TRIGGER_LOW);
- bcsr_init_irq(DB1200_INT_BEGIN, DB1200_INT_END, AU1200_GPIO7_INT);
-
- /* insert/eject pairs: one of both is always screaming. To avoid
- * issues they must not be automatically enabled when initially
- * requested.
- */
- irq_set_status_flags(DB1200_SD0_INSERT_INT, IRQ_NOAUTOEN);
- irq_set_status_flags(DB1200_SD0_EJECT_INT, IRQ_NOAUTOEN);
- irq_set_status_flags(DB1200_PC0_INSERT_INT, IRQ_NOAUTOEN);
- irq_set_status_flags(DB1200_PC0_EJECT_INT, IRQ_NOAUTOEN);
- irq_set_status_flags(DB1200_PC1_INSERT_INT, IRQ_NOAUTOEN);
- irq_set_status_flags(DB1200_PC1_EJECT_INT, IRQ_NOAUTOEN);
- return 0;
-}
-arch_initcall(db1200_arch_init);
diff --git a/arch/mips/alchemy/devboards/db1x00.c b/arch/mips/alchemy/devboards/db1x00.c
new file mode 100644
index 0000000..589ae24
--- /dev/null
+++ b/arch/mips/alchemy/devboards/db1x00.c
@@ -0,0 +1,256 @@
+/*
+ * DBAu1000/1500/1100 board support
+ *
+ * Copyright 2000, 2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@xxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1000_dma.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <asm/reboot.h>
+#include <prom.h>
+#include "platform.h"
+
+struct pci_dev;
+
+const char *get_system_type(void)
+{
+ return "Alchemy Db1x00";
+}
+
+void __init board_setup(void)
+{
+#ifdef CONFIG_MIPS_DB1000
+ printk(KERN_INFO "AMD Alchemy Au1000/Db1000 Board\n");
+#endif
+#ifdef CONFIG_MIPS_DB1500
+ printk(KERN_INFO "AMD Alchemy Au1500/Db1500 Board\n");
+#endif
+#ifdef CONFIG_MIPS_DB1100
+ printk(KERN_INFO "AMD Alchemy Au1100/Db1100 Board\n");
+#endif
+ /* initialize board register space */
+ bcsr_init(DB1000_BCSR_PHYS_ADDR,
+ DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
+
+#if defined(CONFIG_IRDA) && defined(CONFIG_AU1000_FIR)
+ {
+ u32 pin_func;
+
+ /* Set IRFIRSEL instead of GPIO15 */
+ pin_func = au_readl(SYS_PINFUNC) | SYS_PF_IRF;
+ au_writel(pin_func, SYS_PINFUNC);
+ /* Power off until the driver is in use */
+ bcsr_mod(BCSR_RESETS, BCSR_RESETS_IRDA_MODE_MASK,
+ BCSR_RESETS_IRDA_MODE_OFF);
+ }
+#endif
+ bcsr_write(BCSR_PCMCIA, 0); /* turn off PCMCIA power */
+
+ /* Enable GPIO[31:0] inputs */
+ alchemy_gpio1_input_enable();
+}
+
+/* DB1xxx PCMCIA interrupt sources:
+ * CD0/1 GPIO0/3
+ * STSCHG0/1 GPIO1/4
+ * CARD0/1 GPIO2/5
+ */
+
+#define F_SWAPPED (bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT)
+
+#if defined(CONFIG_MIPS_DB1000)
+#define DB1XXX_PCMCIA_CD0 AU1000_GPIO0_INT
+#define DB1XXX_PCMCIA_STSCHG0 AU1000_GPIO1_INT
+#define DB1XXX_PCMCIA_CARD0 AU1000_GPIO2_INT
+#define DB1XXX_PCMCIA_CD1 AU1000_GPIO3_INT
+#define DB1XXX_PCMCIA_STSCHG1 AU1000_GPIO4_INT
+#define DB1XXX_PCMCIA_CARD1 AU1000_GPIO5_INT
+#elif defined(CONFIG_MIPS_DB1100)
+#define DB1XXX_PCMCIA_CD0 AU1100_GPIO0_INT
+#define DB1XXX_PCMCIA_STSCHG0 AU1100_GPIO1_INT
+#define DB1XXX_PCMCIA_CARD0 AU1100_GPIO2_INT
+#define DB1XXX_PCMCIA_CD1 AU1100_GPIO3_INT
+#define DB1XXX_PCMCIA_STSCHG1 AU1100_GPIO4_INT
+#define DB1XXX_PCMCIA_CARD1 AU1100_GPIO5_INT
+#elif defined(CONFIG_MIPS_DB1500)
+#define DB1XXX_PCMCIA_CD0 AU1500_GPIO0_INT
+#define DB1XXX_PCMCIA_STSCHG0 AU1500_GPIO1_INT
+#define DB1XXX_PCMCIA_CARD0 AU1500_GPIO2_INT
+#define DB1XXX_PCMCIA_CD1 AU1500_GPIO3_INT
+#define DB1XXX_PCMCIA_STSCHG1 AU1500_GPIO4_INT
+#define DB1XXX_PCMCIA_CARD1 AU1500_GPIO5_INT
+
+static int db1500_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+ if ((slot < 12) || (slot > 13) || pin == 0)
+ return -1;
+ if (slot == 12)
+ return (pin == 1) ? AU1500_PCI_INTA : 0xff;
+ if (slot == 13) {
+ switch (pin) {
+ case 1: return AU1500_PCI_INTA;
+ case 2: return AU1500_PCI_INTB;
+ case 3: return AU1500_PCI_INTC;
+ case 4: return AU1500_PCI_INTD;
+ }
+ }
+ return -1;
+}
+
+static struct resource alchemy_pci_host_res[] = {
+ [0] = {
+ .start = AU1500_PCI_PHYS_ADDR,
+ .end = AU1500_PCI_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct alchemy_pci_platdata db1500_pci_pd = {
+ .board_map_irq = db1500_map_pci_irq,
+};
+
+static struct platform_device db1500_pci_host_dev = {
+ .dev.platform_data = &db1500_pci_pd,
+ .name = "alchemy-pci",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
+ .resource = alchemy_pci_host_res,
+};
+
+static int __init db1500_pci_init(void)
+{
+ return platform_device_register(&db1500_pci_host_dev);
+}
+/* must be arch_initcall; MIPS PCI scans busses in a subsys_initcall */
+arch_initcall(db1500_pci_init);
+#endif
+
+#ifdef CONFIG_MIPS_DB1100
+static struct resource au1100_lcd_resources[] = {
+ [0] = {
+ .start = AU1100_LCD_PHYS_ADDR,
+ .end = AU1100_LCD_PHYS_ADDR + 0x800 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1100_LCD_INT,
+ .end = AU1100_LCD_INT,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static u64 au1100_lcd_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device au1100_lcd_device = {
+ .name = "au1100-lcd",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1100_lcd_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .num_resources = ARRAY_SIZE(au1100_lcd_resources),
+ .resource = au1100_lcd_resources,
+};
+#endif
+
+static struct resource alchemy_ac97c_res[] = {
+ [0] = {
+ .start = AU1000_AC97_PHYS_ADDR,
+ .end = AU1000_AC97_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = DMA_ID_AC97C_TX,
+ .end = DMA_ID_AC97C_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [2] = {
+ .start = DMA_ID_AC97C_RX,
+ .end = DMA_ID_AC97C_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device alchemy_ac97c_dev = {
+ .name = "alchemy-ac97c",
+ .id = -1,
+ .resource = alchemy_ac97c_res,
+ .num_resources = ARRAY_SIZE(alchemy_ac97c_res),
+};
+
+static struct platform_device alchemy_ac97c_dma_dev = {
+ .name = "alchemy-pcm-dma",
+ .id = 0,
+};
+
+static struct platform_device db1x00_codec_dev = {
+ .name = "ac97-codec",
+ .id = -1,
+};
+
+static struct platform_device db1x00_audio_dev = {
+ .name = "db1000-audio",
+};
+
+static int __init db1xxx_dev_init(void)
+{
+ irq_set_irq_type(DB1XXX_PCMCIA_CD0, IRQ_TYPE_EDGE_BOTH);
+ irq_set_irq_type(DB1XXX_PCMCIA_CD1, IRQ_TYPE_EDGE_BOTH);
+ irq_set_irq_type(DB1XXX_PCMCIA_CARD0, IRQ_TYPE_LEVEL_LOW);
+ irq_set_irq_type(DB1XXX_PCMCIA_CARD1, IRQ_TYPE_LEVEL_LOW);
+ irq_set_irq_type(DB1XXX_PCMCIA_STSCHG0, IRQ_TYPE_LEVEL_LOW);
+ irq_set_irq_type(DB1XXX_PCMCIA_STSCHG1, IRQ_TYPE_LEVEL_LOW);
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ DB1XXX_PCMCIA_CARD0, DB1XXX_PCMCIA_CD0,
+ /*DB1XXX_PCMCIA_STSCHG0*/0, 0, 0);
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x004010000 - 1,
+ DB1XXX_PCMCIA_CARD1, DB1XXX_PCMCIA_CD1,
+ /*DB1XXX_PCMCIA_STSCHG1*/0, 0, 1);
+#ifdef CONFIG_MIPS_DB1100
+ platform_device_register(&au1100_lcd_device);
+#endif
+ platform_device_register(&db1x00_codec_dev);
+ platform_device_register(&alchemy_ac97c_dma_dev);
+ platform_device_register(&alchemy_ac97c_dev);
+ platform_device_register(&db1x00_audio_dev);
+
+ db1x_register_norflash(32 << 20, 4 /* 32bit */, F_SWAPPED);
+ return 0;
+}
+device_initcall(db1xxx_dev_init);
diff --git a/arch/mips/alchemy/devboards/db1x00/Makefile b/arch/mips/alchemy/devboards/db1x00/Makefile
deleted file mode 100644
index 613c0c0..0000000
--- a/arch/mips/alchemy/devboards/db1x00/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# Copyright 2000, 2008 MontaVista Software Inc.
-# Author: MontaVista Software, Inc. <source@xxxxxxxxxx>
-#
-# Makefile for the Alchemy Semiconductor DBAu1xx0 boards.
-#
-
-obj-y := board_setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/db1x00/board_setup.c b/arch/mips/alchemy/devboards/db1x00/board_setup.c
deleted file mode 100644
index 2dbebcb..0000000
--- a/arch/mips/alchemy/devboards/db1x00/board_setup.c
+++ /dev/null
@@ -1,108 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * Alchemy Db1x00 board setup.
- *
- * Copyright 2000, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@xxxxxxxxxx>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/pm.h>
-
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-au1x00/au1xxx_eth.h>
-#include <asm/mach-db1x00/db1x00.h>
-#include <asm/mach-db1x00/bcsr.h>
-#include <asm/reboot.h>
-
-#include <prom.h>
-
-const char *get_system_type(void)
-{
- return "Alchemy Db1x00";
-}
-
-
-void __init board_setup(void)
-{
-#ifdef CONFIG_MIPS_DB1000
- printk(KERN_INFO "AMD Alchemy Au1000/Db1000 Board\n");
-#endif
-#ifdef CONFIG_MIPS_DB1500
- printk(KERN_INFO "AMD Alchemy Au1500/Db1500 Board\n");
-#endif
-#ifdef CONFIG_MIPS_DB1100
- printk(KERN_INFO "AMD Alchemy Au1100/Db1100 Board\n");
-#endif
- /* initialize board register space */
- bcsr_init(DB1000_BCSR_PHYS_ADDR,
- DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
-
-#if defined(CONFIG_IRDA) && defined(CONFIG_AU1000_FIR)
- {
- u32 pin_func;
-
- /* Set IRFIRSEL instead of GPIO15 */
- pin_func = au_readl(SYS_PINFUNC) | SYS_PF_IRF;
- au_writel(pin_func, SYS_PINFUNC);
- /* Power off until the driver is in use */
- bcsr_mod(BCSR_RESETS, BCSR_RESETS_IRDA_MODE_MASK,
- BCSR_RESETS_IRDA_MODE_OFF);
- }
-#endif
- bcsr_write(BCSR_PCMCIA, 0); /* turn off PCMCIA power */
-
- /* Enable GPIO[31:0] inputs */
- alchemy_gpio1_input_enable();
-}
-
-static int __init db1x00_init_irq(void)
-{
-#if defined(CONFIG_MIPS_DB1500)
- irq_set_irq_type(AU1500_GPIO0_INT, IRQF_TRIGGER_LOW); /* CD0# */
- irq_set_irq_type(AU1500_GPIO3_INT, IRQF_TRIGGER_LOW); /* CD1# */
- irq_set_irq_type(AU1500_GPIO2_INT, IRQF_TRIGGER_LOW); /* CARD0# */
- irq_set_irq_type(AU1500_GPIO5_INT, IRQF_TRIGGER_LOW); /* CARD1# */
- irq_set_irq_type(AU1500_GPIO1_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
- irq_set_irq_type(AU1500_GPIO4_INT, IRQF_TRIGGER_LOW); /* STSCHG1# */
-#elif defined(CONFIG_MIPS_DB1100)
- irq_set_irq_type(AU1100_GPIO0_INT, IRQF_TRIGGER_LOW); /* CD0# */
- irq_set_irq_type(AU1100_GPIO3_INT, IRQF_TRIGGER_LOW); /* CD1# */
- irq_set_irq_type(AU1100_GPIO2_INT, IRQF_TRIGGER_LOW); /* CARD0# */
- irq_set_irq_type(AU1100_GPIO5_INT, IRQF_TRIGGER_LOW); /* CARD1# */
- irq_set_irq_type(AU1100_GPIO1_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
- irq_set_irq_type(AU1100_GPIO4_INT, IRQF_TRIGGER_LOW); /* STSCHG1# */
-#elif defined(CONFIG_MIPS_DB1000)
- irq_set_irq_type(AU1000_GPIO0_INT, IRQF_TRIGGER_LOW); /* CD0# */
- irq_set_irq_type(AU1000_GPIO3_INT, IRQF_TRIGGER_LOW); /* CD1# */
- irq_set_irq_type(AU1000_GPIO2_INT, IRQF_TRIGGER_LOW); /* CARD0# */
- irq_set_irq_type(AU1000_GPIO5_INT, IRQF_TRIGGER_LOW); /* CARD1# */
- irq_set_irq_type(AU1000_GPIO1_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
- irq_set_irq_type(AU1000_GPIO4_INT, IRQF_TRIGGER_LOW); /* STSCHG1# */
-#endif
- return 0;
-}
-arch_initcall(db1x00_init_irq);
diff --git a/arch/mips/alchemy/devboards/db1x00/platform.c b/arch/mips/alchemy/devboards/db1x00/platform.c
deleted file mode 100644
index b439b4f..0000000
--- a/arch/mips/alchemy/devboards/db1x00/platform.c
+++ /dev/null
@@ -1,206 +0,0 @@
-/*
- * DBAu1xxx board platform device registration
- *
- * Copyright (C) 2009 Manuel Lauss
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/dma-mapping.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/platform_device.h>
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-au1x00/au1000_dma.h>
-#include <asm/mach-db1x00/bcsr.h>
-#include "../platform.h"
-
-struct pci_dev;
-
-/* DB1xxx PCMCIA interrupt sources:
- * CD0/1 GPIO0/3
- * STSCHG0/1 GPIO1/4
- * CARD0/1 GPIO2/5
- */
-
-#define F_SWAPPED (bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT)
-
-#if defined(CONFIG_MIPS_DB1000)
-#define DB1XXX_PCMCIA_CD0 AU1000_GPIO0_INT
-#define DB1XXX_PCMCIA_STSCHG0 AU1000_GPIO1_INT
-#define DB1XXX_PCMCIA_CARD0 AU1000_GPIO2_INT
-#define DB1XXX_PCMCIA_CD1 AU1000_GPIO3_INT
-#define DB1XXX_PCMCIA_STSCHG1 AU1000_GPIO4_INT
-#define DB1XXX_PCMCIA_CARD1 AU1000_GPIO5_INT
-#elif defined(CONFIG_MIPS_DB1100)
-#define DB1XXX_PCMCIA_CD0 AU1100_GPIO0_INT
-#define DB1XXX_PCMCIA_STSCHG0 AU1100_GPIO1_INT
-#define DB1XXX_PCMCIA_CARD0 AU1100_GPIO2_INT
-#define DB1XXX_PCMCIA_CD1 AU1100_GPIO3_INT
-#define DB1XXX_PCMCIA_STSCHG1 AU1100_GPIO4_INT
-#define DB1XXX_PCMCIA_CARD1 AU1100_GPIO5_INT
-#elif defined(CONFIG_MIPS_DB1500)
-#define DB1XXX_PCMCIA_CD0 AU1500_GPIO0_INT
-#define DB1XXX_PCMCIA_STSCHG0 AU1500_GPIO1_INT
-#define DB1XXX_PCMCIA_CARD0 AU1500_GPIO2_INT
-#define DB1XXX_PCMCIA_CD1 AU1500_GPIO3_INT
-#define DB1XXX_PCMCIA_STSCHG1 AU1500_GPIO4_INT
-#define DB1XXX_PCMCIA_CARD1 AU1500_GPIO5_INT
-
-static int db1500_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
-{
- if ((slot < 12) || (slot > 13) || pin == 0)
- return -1;
- if (slot == 12)
- return (pin == 1) ? AU1500_PCI_INTA : 0xff;
- if (slot == 13) {
- switch (pin) {
- case 1: return AU1500_PCI_INTA;
- case 2: return AU1500_PCI_INTB;
- case 3: return AU1500_PCI_INTC;
- case 4: return AU1500_PCI_INTD;
- }
- }
- return -1;
-}
-
-static struct resource alchemy_pci_host_res[] = {
- [0] = {
- .start = AU1500_PCI_PHYS_ADDR,
- .end = AU1500_PCI_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct alchemy_pci_platdata db1500_pci_pd = {
- .board_map_irq = db1500_map_pci_irq,
-};
-
-static struct platform_device db1500_pci_host_dev = {
- .dev.platform_data = &db1500_pci_pd,
- .name = "alchemy-pci",
- .id = 0,
- .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
- .resource = alchemy_pci_host_res,
-};
-
-static int __init db1500_pci_init(void)
-{
- return platform_device_register(&db1500_pci_host_dev);
-}
-/* must be arch_initcall; MIPS PCI scans busses in a subsys_initcall */
-arch_initcall(db1500_pci_init);
-#endif
-
-#ifdef CONFIG_MIPS_DB1100
-static struct resource au1100_lcd_resources[] = {
- [0] = {
- .start = AU1100_LCD_PHYS_ADDR,
- .end = AU1100_LCD_PHYS_ADDR + 0x800 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1100_LCD_INT,
- .end = AU1100_LCD_INT,
- .flags = IORESOURCE_IRQ,
- }
-};
-
-static u64 au1100_lcd_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device au1100_lcd_device = {
- .name = "au1100-lcd",
- .id = 0,
- .dev = {
- .dma_mask = &au1100_lcd_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(au1100_lcd_resources),
- .resource = au1100_lcd_resources,
-};
-#endif
-
-static struct resource alchemy_ac97c_res[] = {
- [0] = {
- .start = AU1000_AC97_PHYS_ADDR,
- .end = AU1000_AC97_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = DMA_ID_AC97C_TX,
- .end = DMA_ID_AC97C_TX,
- .flags = IORESOURCE_DMA,
- },
- [2] = {
- .start = DMA_ID_AC97C_RX,
- .end = DMA_ID_AC97C_RX,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static struct platform_device alchemy_ac97c_dev = {
- .name = "alchemy-ac97c",
- .id = -1,
- .resource = alchemy_ac97c_res,
- .num_resources = ARRAY_SIZE(alchemy_ac97c_res),
-};
-
-static struct platform_device alchemy_ac97c_dma_dev = {
- .name = "alchemy-pcm-dma",
- .id = 0,
-};
-
-static struct platform_device db1x00_codec_dev = {
- .name = "ac97-codec",
- .id = -1,
-};
-
-static struct platform_device db1x00_audio_dev = {
- .name = "db1000-audio",
-};
-
-static int __init db1xxx_dev_init(void)
-{
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
- DB1XXX_PCMCIA_CARD0, DB1XXX_PCMCIA_CD0,
- /*DB1XXX_PCMCIA_STSCHG0*/0, 0, 0);
-
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004000000,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x004000000,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x004010000 - 1,
- DB1XXX_PCMCIA_CARD1, DB1XXX_PCMCIA_CD1,
- /*DB1XXX_PCMCIA_STSCHG1*/0, 0, 1);
-#ifdef CONFIG_MIPS_DB1100
- platform_device_register(&au1100_lcd_device);
-#endif
- platform_device_register(&db1x00_codec_dev);
- platform_device_register(&alchemy_ac97c_dma_dev);
- platform_device_register(&alchemy_ac97c_dev);
- platform_device_register(&db1x00_audio_dev);
-
- db1x_register_norflash(0x02000000, 4 /* 32bit */, F_SWAPPED);
- return 0;
-}
-device_initcall(db1xxx_dev_init);
diff --git a/arch/mips/alchemy/devboards/pb1100.c b/arch/mips/alchemy/devboards/pb1100.c
new file mode 100644
index 0000000..cff50d0
--- /dev/null
+++ b/arch/mips/alchemy/devboards/pb1100.c
@@ -0,0 +1,167 @@
+/*
+ * Pb1100 board platform device registration
+ *
+ * Copyright (C) 2009 Manuel Lauss
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/delay.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <prom.h>
+#include "platform.h"
+
+const char *get_system_type(void)
+{
+ return "PB1100";
+}
+
+void __init board_setup(void)
+{
+ volatile void __iomem *base = (volatile void __iomem *)0xac000000UL;
+
+ bcsr_init(DB1000_BCSR_PHYS_ADDR,
+ DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
+
+ /* Set AUX clock to 12 MHz * 8 = 96 MHz */
+ au_writel(8, SYS_AUXPLL);
+ alchemy_gpio1_input_enable();
+ udelay(100);
+
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+ {
+ u32 pin_func, sys_freqctrl, sys_clksrc;
+
+ /* Configure pins GPIO[14:9] as GPIO */
+ pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_UR3;
+
+ /* Zero and disable FREQ2 */
+ sys_freqctrl = au_readl(SYS_FREQCTRL0);
+ sys_freqctrl &= ~0xFFF00000;
+ au_writel(sys_freqctrl, SYS_FREQCTRL0);
+
+ /* Zero and disable USBH/USBD/IrDA clock */
+ sys_clksrc = au_readl(SYS_CLKSRC);
+ sys_clksrc &= ~(SYS_CS_CIR | SYS_CS_DIR | SYS_CS_MIR_MASK);
+ au_writel(sys_clksrc, SYS_CLKSRC);
+
+ sys_freqctrl = au_readl(SYS_FREQCTRL0);
+ sys_freqctrl &= ~0xFFF00000;
+
+ sys_clksrc = au_readl(SYS_CLKSRC);
+ sys_clksrc &= ~(SYS_CS_CIR | SYS_CS_DIR | SYS_CS_MIR_MASK);
+
+ /* FREQ2 = aux / 2 = 48 MHz */
+ sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) |
+ SYS_FC_FE2 | SYS_FC_FS2;
+ au_writel(sys_freqctrl, SYS_FREQCTRL0);
+
+ /*
+ * Route 48 MHz FREQ2 into USBH/USBD/IrDA
+ */
+ sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MIR_BIT;
+ au_writel(sys_clksrc, SYS_CLKSRC);
+
+ /* Setup the static bus controller */
+ au_writel(0x00000002, MEM_STCFG3); /* type = PCMCIA */
+ au_writel(0x280E3D07, MEM_STTIME3); /* 250ns cycle time */
+ au_writel(0x10000000, MEM_STADDR3); /* any PCMCIA select */
+
+ /*
+ * Get USB Functionality pin state (device vs host drive pins).
+ */
+ pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_USB;
+ /* 2nd USB port is USB host. */
+ pin_func |= SYS_PF_USB;
+ au_writel(pin_func, SYS_PINFUNC);
+ }
+#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
+
+ /* Enable sys bus clock divider when IDLE state or no bus activity. */
+ au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
+
+ /* Enable the RTC if not already enabled. */
+ if (!(readb(base + 0x28) & 0x20)) {
+ writeb(readb(base + 0x28) | 0x20, base + 0x28);
+ au_sync();
+ }
+ /* Put the clock in BCD mode. */
+ if (readb(base + 0x2C) & 0x4) { /* reg B */
+ writeb(readb(base + 0x2c) & ~0x4, base + 0x2c);
+ au_sync();
+ }
+}
+
+/******************************************************************************/
+
+static struct resource au1100_lcd_resources[] = {
+ [0] = {
+ .start = AU1100_LCD_PHYS_ADDR,
+ .end = AU1100_LCD_PHYS_ADDR + 0x800 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1100_LCD_INT,
+ .end = AU1100_LCD_INT,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static u64 au1100_lcd_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device au1100_lcd_device = {
+ .name = "au1100-lcd",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1100_lcd_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .num_resources = ARRAY_SIZE(au1100_lcd_resources),
+ .resource = au1100_lcd_resources,
+};
+
+static int __init pb1100_dev_init(void)
+{
+ int swapped;
+
+ irq_set_irq_type(AU1100_GPIO9_INT, IRQF_TRIGGER_LOW); /* PCCD# */
+ irq_set_irq_type(AU1100_GPIO10_INT, IRQF_TRIGGER_LOW); /* PCSTSCHG# */
+ irq_set_irq_type(AU1100_GPIO11_INT, IRQF_TRIGGER_LOW); /* PCCard# */
+ irq_set_irq_type(AU1100_GPIO13_INT, IRQF_TRIGGER_LOW); /* DC_IRQ# */
+
+ /* PCMCIA. single socket, identical to Pb1500 */
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ AU1100_GPIO11_INT, AU1100_GPIO9_INT, /* card / insert */
+ /*AU1100_GPIO10_INT*/0, 0, 0); /* stschg / eject / id */
+
+ swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT;
+ db1x_register_norflash(64 * 1024 * 1024, 4, swapped);
+ platform_device_register(&au1100_lcd_device);
+
+ return 0;
+}
+device_initcall(pb1100_dev_init);
diff --git a/arch/mips/alchemy/devboards/pb1100/Makefile b/arch/mips/alchemy/devboards/pb1100/Makefile
deleted file mode 100644
index 7e3756c..0000000
--- a/arch/mips/alchemy/devboards/pb1100/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# Copyright 2000, 2001, 2008 MontaVista Software Inc.
-# Author: MontaVista Software, Inc. <source@xxxxxxxxxx>
-#
-# Makefile for the Alchemy Semiconductor Pb1100 board.
-#
-
-obj-y := board_setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/pb1100/board_setup.c b/arch/mips/alchemy/devboards/pb1100/board_setup.c
deleted file mode 100644
index d108fd5..0000000
--- a/arch/mips/alchemy/devboards/pb1100/board_setup.c
+++ /dev/null
@@ -1,127 +0,0 @@
-/*
- * Copyright 2002, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@xxxxxxxxxx>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/interrupt.h>
-
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-db1x00/bcsr.h>
-
-#include <prom.h>
-
-
-const char *get_system_type(void)
-{
- return "Alchemy Pb1100";
-}
-
-void __init board_setup(void)
-{
- volatile void __iomem *base = (volatile void __iomem *)0xac000000UL;
-
- bcsr_init(DB1000_BCSR_PHYS_ADDR,
- DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
-
- /* Set AUX clock to 12 MHz * 8 = 96 MHz */
- au_writel(8, SYS_AUXPLL);
- alchemy_gpio1_input_enable();
- udelay(100);
-
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
- {
- u32 pin_func, sys_freqctrl, sys_clksrc;
-
- /* Configure pins GPIO[14:9] as GPIO */
- pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_UR3;
-
- /* Zero and disable FREQ2 */
- sys_freqctrl = au_readl(SYS_FREQCTRL0);
- sys_freqctrl &= ~0xFFF00000;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
- /* Zero and disable USBH/USBD/IrDA clock */
- sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~(SYS_CS_CIR | SYS_CS_DIR | SYS_CS_MIR_MASK);
- au_writel(sys_clksrc, SYS_CLKSRC);
-
- sys_freqctrl = au_readl(SYS_FREQCTRL0);
- sys_freqctrl &= ~0xFFF00000;
-
- sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~(SYS_CS_CIR | SYS_CS_DIR | SYS_CS_MIR_MASK);
-
- /* FREQ2 = aux / 2 = 48 MHz */
- sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) |
- SYS_FC_FE2 | SYS_FC_FS2;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
- /*
- * Route 48 MHz FREQ2 into USBH/USBD/IrDA
- */
- sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MIR_BIT;
- au_writel(sys_clksrc, SYS_CLKSRC);
-
- /* Setup the static bus controller */
- au_writel(0x00000002, MEM_STCFG3); /* type = PCMCIA */
- au_writel(0x280E3D07, MEM_STTIME3); /* 250ns cycle time */
- au_writel(0x10000000, MEM_STADDR3); /* any PCMCIA select */
-
- /*
- * Get USB Functionality pin state (device vs host drive pins).
- */
- pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_USB;
- /* 2nd USB port is USB host. */
- pin_func |= SYS_PF_USB;
- au_writel(pin_func, SYS_PINFUNC);
- }
-#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
-
- /* Enable sys bus clock divider when IDLE state or no bus activity. */
- au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
-
- /* Enable the RTC if not already enabled. */
- if (!(readb(base + 0x28) & 0x20)) {
- writeb(readb(base + 0x28) | 0x20, base + 0x28);
- au_sync();
- }
- /* Put the clock in BCD mode. */
- if (readb(base + 0x2C) & 0x4) { /* reg B */
- writeb(readb(base + 0x2c) & ~0x4, base + 0x2c);
- au_sync();
- }
-}
-
-static int __init pb1100_init_irq(void)
-{
- irq_set_irq_type(AU1100_GPIO9_INT, IRQF_TRIGGER_LOW); /* PCCD# */
- irq_set_irq_type(AU1100_GPIO10_INT, IRQF_TRIGGER_LOW); /* PCSTSCHG# */
- irq_set_irq_type(AU1100_GPIO11_INT, IRQF_TRIGGER_LOW); /* PCCard# */
- irq_set_irq_type(AU1100_GPIO13_INT, IRQF_TRIGGER_LOW); /* DC_IRQ# */
-
- return 0;
-}
-arch_initcall(pb1100_init_irq);
diff --git a/arch/mips/alchemy/devboards/pb1100/platform.c b/arch/mips/alchemy/devboards/pb1100/platform.c
deleted file mode 100644
index 9c57c01..0000000
--- a/arch/mips/alchemy/devboards/pb1100/platform.c
+++ /dev/null
@@ -1,77 +0,0 @@
-/*
- * Pb1100 board platform device registration
- *
- * Copyright (C) 2009 Manuel Lauss
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/init.h>
-#include <linux/dma-mapping.h>
-#include <linux/platform_device.h>
-
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-db1x00/bcsr.h>
-
-#include "../platform.h"
-
-static struct resource au1100_lcd_resources[] = {
- [0] = {
- .start = AU1100_LCD_PHYS_ADDR,
- .end = AU1100_LCD_PHYS_ADDR + 0x800 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1100_LCD_INT,
- .end = AU1100_LCD_INT,
- .flags = IORESOURCE_IRQ,
- }
-};
-
-static u64 au1100_lcd_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device au1100_lcd_device = {
- .name = "au1100-lcd",
- .id = 0,
- .dev = {
- .dma_mask = &au1100_lcd_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(au1100_lcd_resources),
- .resource = au1100_lcd_resources,
-};
-
-static int __init pb1100_dev_init(void)
-{
- int swapped;
-
- /* PCMCIA. single socket, identical to Pb1500 */
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
- AU1100_GPIO11_INT, AU1100_GPIO9_INT, /* card / insert */
- /*AU1100_GPIO10_INT*/0, 0, 0); /* stschg / eject / id */
-
- swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT;
- db1x_register_norflash(64 * 1024 * 1024, 4, swapped);
- platform_device_register(&au1100_lcd_device);
-
- return 0;
-}
-device_initcall(pb1100_dev_init);
diff --git a/arch/mips/alchemy/devboards/pb1200.c b/arch/mips/alchemy/devboards/pb1200.c
new file mode 100644
index 0000000..a1b6497
--- /dev/null
+++ b/arch/mips/alchemy/devboards/pb1200.c
@@ -0,0 +1,464 @@
+/*
+ * Pb1200/DBAu1200 board platform device registration
+ *
+ * Copyright (C) 2008 MontaVista Software Inc. <source@xxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/leds.h>
+#include <linux/platform_device.h>
+#include <linux/smc91x.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1100_mmc.h>
+#include <asm/mach-au1x00/au1xxx_dbdma.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <asm/mach-pb1x00/pb1200.h>
+#include <prom.h>
+#include "platform.h"
+
+
+const char *get_system_type(void)
+{
+ return "PB1200";
+}
+
+void __init board_setup(void)
+{
+ printk(KERN_INFO "AMD Alchemy Pb1200 Board\n");
+ bcsr_init(PB1200_BCSR_PHYS_ADDR,
+ PB1200_BCSR_PHYS_ADDR + PB1200_BCSR_HEXLED_OFS);
+
+#if 0
+ {
+ u32 pin_func;
+
+ /*
+ * Enable PSC1 SYNC for AC97. Normaly done in audio driver,
+ * but it is board specific code, so put it here.
+ */
+ pin_func = au_readl(SYS_PINFUNC);
+ au_sync();
+ pin_func |= SYS_PF_MUST_BE_SET | SYS_PF_PSC1_S1;
+ au_writel(pin_func, SYS_PINFUNC);
+
+ au_writel(0, (u32)bcsr | 0x10); /* turn off PCMCIA power */
+ au_sync();
+ }
+#endif
+
+#if defined(CONFIG_I2C_AU1550)
+ {
+ u32 freq0, clksrc;
+ u32 pin_func;
+
+ /* Select SMBus in CPLD */
+ bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
+
+ pin_func = au_readl(SYS_PINFUNC);
+ au_sync();
+ pin_func &= ~(SYS_PINFUNC_P0A | SYS_PINFUNC_P0B);
+ /* Set GPIOs correctly */
+ pin_func |= 2 << 17;
+ au_writel(pin_func, SYS_PINFUNC);
+ au_sync();
+
+ /* The I2C driver depends on 50 MHz clock */
+ freq0 = au_readl(SYS_FREQCTRL0);
+ au_sync();
+ freq0 &= ~(SYS_FC_FRDIV1_MASK | SYS_FC_FS1 | SYS_FC_FE1);
+ freq0 |= 3 << SYS_FC_FRDIV1_BIT;
+ /* 396 MHz / (3 + 1) * 2 == 49.5 MHz */
+ au_writel(freq0, SYS_FREQCTRL0);
+ au_sync();
+ freq0 |= SYS_FC_FE1;
+ au_writel(freq0, SYS_FREQCTRL0);
+ au_sync();
+
+ clksrc = au_readl(SYS_CLKSRC);
+ au_sync();
+ clksrc &= ~(SYS_CS_CE0 | SYS_CS_DE0 | SYS_CS_ME0_MASK);
+ /* Bit 22 is EXTCLK0 for PSC0 */
+ clksrc |= SYS_CS_MUX_FQ1 << SYS_CS_ME0_BIT;
+ au_writel(clksrc, SYS_CLKSRC);
+ au_sync();
+ }
+#endif
+
+ /*
+ * The Pb1200 development board uses external MUX for PSC0 to
+ * support SMB/SPI. bcsr_resets bit 12: 0=SMB 1=SPI
+ */
+#ifdef CONFIG_I2C_AU1550
+ bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
+#endif
+ au_sync();
+}
+
+/******************************************************************************/
+
+static int mmc_activity;
+
+static void pb1200mmc0_set_power(void *mmc_host, int state)
+{
+ if (state)
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD0PWR);
+ else
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD0PWR, 0);
+
+ msleep(1);
+}
+
+static int pb1200mmc0_card_readonly(void *mmc_host)
+{
+ return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD0WP) ? 1 : 0;
+}
+
+static int pb1200mmc0_card_inserted(void *mmc_host)
+{
+ return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD0INSERT) ? 1 : 0;
+}
+
+static void pb1200_mmcled_set(struct led_classdev *led,
+ enum led_brightness brightness)
+{
+ if (brightness != LED_OFF) {
+ if (++mmc_activity == 1)
+ bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED0, 0);
+ } else {
+ if (--mmc_activity == 0)
+ bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED0);
+ }
+}
+
+static struct led_classdev pb1200mmc_led = {
+ .brightness_set = pb1200_mmcled_set,
+};
+
+static void pb1200mmc1_set_power(void *mmc_host, int state)
+{
+ if (state)
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD1PWR);
+ else
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD1PWR, 0);
+
+ msleep(1);
+}
+
+static int pb1200mmc1_card_readonly(void *mmc_host)
+{
+ return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD1WP) ? 1 : 0;
+}
+
+static int pb1200mmc1_card_inserted(void *mmc_host)
+{
+ return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD1INSERT) ? 1 : 0;
+}
+
+static struct au1xmmc_platform_data pb1200mmc_platdata[2] = {
+ [0] = {
+ .set_power = pb1200mmc0_set_power,
+ .card_inserted = pb1200mmc0_card_inserted,
+ .card_readonly = pb1200mmc0_card_readonly,
+ .cd_setup = NULL, /* use poll-timer in driver */
+ .led = &pb1200mmc_led,
+ },
+ [1] = {
+ .set_power = pb1200mmc1_set_power,
+ .card_inserted = pb1200mmc1_card_inserted,
+ .card_readonly = pb1200mmc1_card_readonly,
+ .cd_setup = NULL, /* use poll-timer in driver */
+ .led = &pb1200mmc_led,
+ },
+};
+
+static u64 au1xxx_mmc_dmamask = DMA_BIT_MASK(32);
+
+static struct resource au1200_mmc0_res[] = {
+ [0] = {
+ .start = AU1100_SD0_PHYS_ADDR,
+ .end = AU1100_SD0_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_SD_INT,
+ .end = AU1200_SD_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1200_DSCR_CMD0_SDMS_TX0,
+ .end = AU1200_DSCR_CMD0_SDMS_TX0,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1200_DSCR_CMD0_SDMS_RX0,
+ .end = AU1200_DSCR_CMD0_SDMS_RX0,
+ .flags = IORESOURCE_DMA,
+ }
+};
+
+static struct platform_device pb1200_mmc0_dev = {
+ .name = "au1xxx-mmc",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1xxx_mmc_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &pb1200mmc_platdata[0],
+ },
+ .num_resources = ARRAY_SIZE(au1200_mmc0_res),
+ .resource = au1200_mmc0_res,
+};
+
+static struct resource au1200_mmc1_res[] = {
+ [0] = {
+ .start = AU1100_SD1_PHYS_ADDR,
+ .end = AU1100_SD1_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_SD_INT,
+ .end = AU1200_SD_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1200_DSCR_CMD0_SDMS_TX1,
+ .end = AU1200_DSCR_CMD0_SDMS_TX1,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1200_DSCR_CMD0_SDMS_RX1,
+ .end = AU1200_DSCR_CMD0_SDMS_RX1,
+ .flags = IORESOURCE_DMA,
+ }
+};
+
+static struct platform_device pb1200_mmc1_dev = {
+ .name = "au1xxx-mmc",
+ .id = 1,
+ .dev = {
+ .dma_mask = &au1xxx_mmc_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &pb1200mmc_platdata[1],
+ },
+ .num_resources = ARRAY_SIZE(au1200_mmc1_res),
+ .resource = au1200_mmc1_res,
+};
+
+
+static struct resource ide_resources[] = {
+ [0] = {
+ .start = IDE_PHYS_ADDR,
+ .end = IDE_PHYS_ADDR + IDE_PHYS_LEN - 1,
+ .flags = IORESOURCE_MEM
+ },
+ [1] = {
+ .start = IDE_INT,
+ .end = IDE_INT,
+ .flags = IORESOURCE_IRQ
+ },
+ [2] = {
+ .start = AU1200_DSCR_CMD0_DMA_REQ1,
+ .end = AU1200_DSCR_CMD0_DMA_REQ1,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static u64 au1200_ide_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device ide_device = {
+ .name = "au1200-ide",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1200_ide_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .num_resources = ARRAY_SIZE(ide_resources),
+ .resource = ide_resources
+};
+
+static struct smc91x_platdata smc_data = {
+ .flags = SMC91X_NOWAIT | SMC91X_USE_16BIT,
+ .leda = RPC_LED_100_10,
+ .ledb = RPC_LED_TX_RX,
+};
+
+static struct resource smc91c111_resources[] = {
+ [0] = {
+ .name = "smc91x-regs",
+ .start = SMC91C111_PHYS_ADDR,
+ .end = SMC91C111_PHYS_ADDR + 0xf,
+ .flags = IORESOURCE_MEM
+ },
+ [1] = {
+ .start = SMC91C111_INT,
+ .end = SMC91C111_INT,
+ .flags = IORESOURCE_IRQ
+ },
+};
+
+static struct platform_device smc91c111_device = {
+ .dev = {
+ .platform_data = &smc_data,
+ },
+ .name = "smc91x",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(smc91c111_resources),
+ .resource = smc91c111_resources
+};
+
+static struct resource au1200_psc0_res[] = {
+ [0] = {
+ .start = AU1550_PSC0_PHYS_ADDR,
+ .end = AU1550_PSC0_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_PSC0_INT,
+ .end = AU1200_PSC0_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1200_DSCR_CMD0_PSC0_TX,
+ .end = AU1200_DSCR_CMD0_PSC0_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1200_DSCR_CMD0_PSC0_RX,
+ .end = AU1200_DSCR_CMD0_PSC0_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device pb1200_i2c_dev = {
+ .name = "au1xpsc_smbus",
+ .id = 0, /* bus number */
+ .num_resources = ARRAY_SIZE(au1200_psc0_res),
+ .resource = au1200_psc0_res,
+};
+
+static struct resource au1200_lcd_res[] = {
+ [0] = {
+ .start = AU1200_LCD_PHYS_ADDR,
+ .end = AU1200_LCD_PHYS_ADDR + 0x800 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_LCD_INT,
+ .end = AU1200_LCD_INT,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static u64 au1200_lcd_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device au1200_lcd_dev = {
+ .name = "au1200-lcd",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1200_lcd_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .num_resources = ARRAY_SIZE(au1200_lcd_res),
+ .resource = au1200_lcd_res,
+};
+
+static struct platform_device *board_platform_devices[] __initdata = {
+ &ide_device,
+ &smc91c111_device,
+ &pb1200_i2c_dev,
+ &pb1200_mmc0_dev,
+ &pb1200_mmc1_dev,
+ &au1200_lcd_dev,
+};
+
+static int __init board_register_devices(void)
+{
+ int swapped;
+
+ /* We have a problem with CPLD rev 3. */
+ if (BCSR_WHOAMI_CPLD(bcsr_read(BCSR_WHOAMI)) <= 3) {
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "Pb1200 must be at CPLD rev 4. Please have Pb1200\n");
+ printk(KERN_ERR "updated to latest revision. This software will\n");
+ printk(KERN_ERR "not work on anything less than CPLD rev 4.\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ panic("Game over. Your score is 0.");
+ }
+
+ irq_set_irq_type(AU1200_GPIO7_INT, IRQF_TRIGGER_LOW);
+ bcsr_init_irq(PB1200_INT_BEGIN, PB1200_INT_END, AU1200_GPIO7_INT);
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ PB1200_PC0_INT, PB1200_PC0_INSERT_INT,
+ /*PB1200_PC0_STSCHG_INT*/0, PB1200_PC0_EJECT_INT, 0);
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008000000,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008000000,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x008000000,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x008010000 - 1,
+ PB1200_PC1_INT, PB1200_PC1_INSERT_INT,
+ /*PB1200_PC1_STSCHG_INT*/0, PB1200_PC1_EJECT_INT, 1);
+
+ swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1200_SWAPBOOT;
+ db1x_register_norflash(128 * 1024 * 1024, 2, swapped);
+
+ return platform_add_devices(board_platform_devices,
+ ARRAY_SIZE(board_platform_devices));
+}
+device_initcall(board_register_devices);
+
+
+int board_au1200fb_panel(void)
+{
+ return (bcsr_read(BCSR_SWITCHES) >> 8) & 0x0f;
+}
+
+int board_au1200fb_panel_init(void)
+{
+ /* Apply power */
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+ BCSR_BOARD_LCDBL);
+ return 0;
+}
+
+int board_au1200fb_panel_shutdown(void)
+{
+ /* Remove power */
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+ BCSR_BOARD_LCDBL, 0);
+ return 0;
+}
diff --git a/arch/mips/alchemy/devboards/pb1200/Makefile b/arch/mips/alchemy/devboards/pb1200/Makefile
deleted file mode 100644
index 18c1bd5..0000000
--- a/arch/mips/alchemy/devboards/pb1200/Makefile
+++ /dev/null
@@ -1,5 +0,0 @@
-#
-# Makefile for the Alchemy Semiconductor Pb1200/DBAu1200 boards.
-#
-
-obj-y := board_setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/pb1200/board_setup.c b/arch/mips/alchemy/devboards/pb1200/board_setup.c
deleted file mode 100644
index 6d06b07..0000000
--- a/arch/mips/alchemy/devboards/pb1200/board_setup.c
+++ /dev/null
@@ -1,174 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * Alchemy Pb1200/Db1200 board setup.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/sched.h>
-
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-db1x00/bcsr.h>
-
-#ifdef CONFIG_MIPS_PB1200
-#include <asm/mach-pb1x00/pb1200.h>
-#endif
-
-#ifdef CONFIG_MIPS_DB1200
-#include <asm/mach-db1x00/db1200.h>
-#define PB1200_INT_BEGIN DB1200_INT_BEGIN
-#define PB1200_INT_END DB1200_INT_END
-#endif
-
-#include <prom.h>
-
-const char *get_system_type(void)
-{
- return "Alchemy Pb1200";
-}
-
-void __init board_setup(void)
-{
- printk(KERN_INFO "AMD Alchemy Pb1200 Board\n");
- bcsr_init(PB1200_BCSR_PHYS_ADDR,
- PB1200_BCSR_PHYS_ADDR + PB1200_BCSR_HEXLED_OFS);
-
-#if 0
- {
- u32 pin_func;
-
- /*
- * Enable PSC1 SYNC for AC97. Normaly done in audio driver,
- * but it is board specific code, so put it here.
- */
- pin_func = au_readl(SYS_PINFUNC);
- au_sync();
- pin_func |= SYS_PF_MUST_BE_SET | SYS_PF_PSC1_S1;
- au_writel(pin_func, SYS_PINFUNC);
-
- au_writel(0, (u32)bcsr | 0x10); /* turn off PCMCIA power */
- au_sync();
- }
-#endif
-
-#if defined(CONFIG_I2C_AU1550)
- {
- u32 freq0, clksrc;
- u32 pin_func;
-
- /* Select SMBus in CPLD */
- bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
-
- pin_func = au_readl(SYS_PINFUNC);
- au_sync();
- pin_func &= ~(SYS_PINFUNC_P0A | SYS_PINFUNC_P0B);
- /* Set GPIOs correctly */
- pin_func |= 2 << 17;
- au_writel(pin_func, SYS_PINFUNC);
- au_sync();
-
- /* The I2C driver depends on 50 MHz clock */
- freq0 = au_readl(SYS_FREQCTRL0);
- au_sync();
- freq0 &= ~(SYS_FC_FRDIV1_MASK | SYS_FC_FS1 | SYS_FC_FE1);
- freq0 |= 3 << SYS_FC_FRDIV1_BIT;
- /* 396 MHz / (3 + 1) * 2 == 49.5 MHz */
- au_writel(freq0, SYS_FREQCTRL0);
- au_sync();
- freq0 |= SYS_FC_FE1;
- au_writel(freq0, SYS_FREQCTRL0);
- au_sync();
-
- clksrc = au_readl(SYS_CLKSRC);
- au_sync();
- clksrc &= ~(SYS_CS_CE0 | SYS_CS_DE0 | SYS_CS_ME0_MASK);
- /* Bit 22 is EXTCLK0 for PSC0 */
- clksrc |= SYS_CS_MUX_FQ1 << SYS_CS_ME0_BIT;
- au_writel(clksrc, SYS_CLKSRC);
- au_sync();
- }
-#endif
-
- /*
- * The Pb1200 development board uses external MUX for PSC0 to
- * support SMB/SPI. bcsr_resets bit 12: 0=SMB 1=SPI
- */
-#ifdef CONFIG_I2C_AU1550
- bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
-#endif
- au_sync();
-}
-
-static int __init pb1200_init_irq(void)
-{
- /* We have a problem with CPLD rev 3. */
- if (BCSR_WHOAMI_CPLD(bcsr_read(BCSR_WHOAMI)) <= 3) {
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "Pb1200 must be at CPLD rev 4. Please have Pb1200\n");
- printk(KERN_ERR "updated to latest revision. This software will\n");
- printk(KERN_ERR "not work on anything less than CPLD rev 4.\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- panic("Game over. Your score is 0.");
- }
-
- irq_set_irq_type(AU1200_GPIO7_INT, IRQF_TRIGGER_LOW);
- bcsr_init_irq(PB1200_INT_BEGIN, PB1200_INT_END, AU1200_GPIO7_INT);
-
- return 0;
-}
-arch_initcall(pb1200_init_irq);
-
-
-int board_au1200fb_panel(void)
-{
- return (bcsr_read(BCSR_SWITCHES) >> 8) & 0x0f;
-}
-
-int board_au1200fb_panel_init(void)
-{
- /* Apply power */
- bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
- BCSR_BOARD_LCDBL);
- /* printk(KERN_DEBUG "board_au1200fb_panel_init()\n"); */
- return 0;
-}
-
-int board_au1200fb_panel_shutdown(void)
-{
- /* Remove power */
- bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
- BCSR_BOARD_LCDBL, 0);
- /* printk(KERN_DEBUG "board_au1200fb_panel_shutdown()\n"); */
- return 0;
-}
diff --git a/arch/mips/alchemy/devboards/pb1200/platform.c b/arch/mips/alchemy/devboards/pb1200/platform.c
deleted file mode 100644
index 54f7f7b..0000000
--- a/arch/mips/alchemy/devboards/pb1200/platform.c
+++ /dev/null
@@ -1,339 +0,0 @@
-/*
- * Pb1200/DBAu1200 board platform device registration
- *
- * Copyright (C) 2008 MontaVista Software Inc. <source@xxxxxxxxxx>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/dma-mapping.h>
-#include <linux/init.h>
-#include <linux/leds.h>
-#include <linux/platform_device.h>
-#include <linux/smc91x.h>
-
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-au1x00/au1100_mmc.h>
-#include <asm/mach-au1x00/au1xxx_dbdma.h>
-#include <asm/mach-db1x00/bcsr.h>
-#include <asm/mach-pb1x00/pb1200.h>
-
-#include "../platform.h"
-
-static int mmc_activity;
-
-static void pb1200mmc0_set_power(void *mmc_host, int state)
-{
- if (state)
- bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD0PWR);
- else
- bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD0PWR, 0);
-
- msleep(1);
-}
-
-static int pb1200mmc0_card_readonly(void *mmc_host)
-{
- return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD0WP) ? 1 : 0;
-}
-
-static int pb1200mmc0_card_inserted(void *mmc_host)
-{
- return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD0INSERT) ? 1 : 0;
-}
-
-static void pb1200_mmcled_set(struct led_classdev *led,
- enum led_brightness brightness)
-{
- if (brightness != LED_OFF) {
- if (++mmc_activity == 1)
- bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED0, 0);
- } else {
- if (--mmc_activity == 0)
- bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED0);
- }
-}
-
-static struct led_classdev pb1200mmc_led = {
- .brightness_set = pb1200_mmcled_set,
-};
-
-static void pb1200mmc1_set_power(void *mmc_host, int state)
-{
- if (state)
- bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD1PWR);
- else
- bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD1PWR, 0);
-
- msleep(1);
-}
-
-static int pb1200mmc1_card_readonly(void *mmc_host)
-{
- return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD1WP) ? 1 : 0;
-}
-
-static int pb1200mmc1_card_inserted(void *mmc_host)
-{
- return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD1INSERT) ? 1 : 0;
-}
-
-static struct au1xmmc_platform_data pb1200mmc_platdata[2] = {
- [0] = {
- .set_power = pb1200mmc0_set_power,
- .card_inserted = pb1200mmc0_card_inserted,
- .card_readonly = pb1200mmc0_card_readonly,
- .cd_setup = NULL, /* use poll-timer in driver */
- .led = &pb1200mmc_led,
- },
- [1] = {
- .set_power = pb1200mmc1_set_power,
- .card_inserted = pb1200mmc1_card_inserted,
- .card_readonly = pb1200mmc1_card_readonly,
- .cd_setup = NULL, /* use poll-timer in driver */
- .led = &pb1200mmc_led,
- },
-};
-
-static u64 au1xxx_mmc_dmamask = DMA_BIT_MASK(32);
-
-static struct resource au1200_mmc0_res[] = {
- [0] = {
- .start = AU1100_SD0_PHYS_ADDR,
- .end = AU1100_SD0_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_SD_INT,
- .end = AU1200_SD_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_SDMS_TX0,
- .end = AU1200_DSCR_CMD0_SDMS_TX0,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = AU1200_DSCR_CMD0_SDMS_RX0,
- .end = AU1200_DSCR_CMD0_SDMS_RX0,
- .flags = IORESOURCE_DMA,
- }
-};
-
-static struct platform_device pb1200_mmc0_dev = {
- .name = "au1xxx-mmc",
- .id = 0,
- .dev = {
- .dma_mask = &au1xxx_mmc_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &pb1200mmc_platdata[0],
- },
- .num_resources = ARRAY_SIZE(au1200_mmc0_res),
- .resource = au1200_mmc0_res,
-};
-
-static struct resource au1200_mmc1_res[] = {
- [0] = {
- .start = AU1100_SD1_PHYS_ADDR,
- .end = AU1100_SD1_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_SD_INT,
- .end = AU1200_SD_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_SDMS_TX1,
- .end = AU1200_DSCR_CMD0_SDMS_TX1,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = AU1200_DSCR_CMD0_SDMS_RX1,
- .end = AU1200_DSCR_CMD0_SDMS_RX1,
- .flags = IORESOURCE_DMA,
- }
-};
-
-static struct platform_device pb1200_mmc1_dev = {
- .name = "au1xxx-mmc",
- .id = 1,
- .dev = {
- .dma_mask = &au1xxx_mmc_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &pb1200mmc_platdata[1],
- },
- .num_resources = ARRAY_SIZE(au1200_mmc1_res),
- .resource = au1200_mmc1_res,
-};
-
-
-static struct resource ide_resources[] = {
- [0] = {
- .start = IDE_PHYS_ADDR,
- .end = IDE_PHYS_ADDR + IDE_PHYS_LEN - 1,
- .flags = IORESOURCE_MEM
- },
- [1] = {
- .start = IDE_INT,
- .end = IDE_INT,
- .flags = IORESOURCE_IRQ
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_DMA_REQ1,
- .end = AU1200_DSCR_CMD0_DMA_REQ1,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static u64 ide_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device ide_device = {
- .name = "au1200-ide",
- .id = 0,
- .dev = {
- .dma_mask = &ide_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(ide_resources),
- .resource = ide_resources
-};
-
-static struct smc91x_platdata smc_data = {
- .flags = SMC91X_NOWAIT | SMC91X_USE_16BIT,
- .leda = RPC_LED_100_10,
- .ledb = RPC_LED_TX_RX,
-};
-
-static struct resource smc91c111_resources[] = {
- [0] = {
- .name = "smc91x-regs",
- .start = SMC91C111_PHYS_ADDR,
- .end = SMC91C111_PHYS_ADDR + 0xf,
- .flags = IORESOURCE_MEM
- },
- [1] = {
- .start = SMC91C111_INT,
- .end = SMC91C111_INT,
- .flags = IORESOURCE_IRQ
- },
-};
-
-static struct platform_device smc91c111_device = {
- .dev = {
- .platform_data = &smc_data,
- },
- .name = "smc91x",
- .id = -1,
- .num_resources = ARRAY_SIZE(smc91c111_resources),
- .resource = smc91c111_resources
-};
-
-static struct resource au1200_psc0_res[] = {
- [0] = {
- .start = AU1550_PSC0_PHYS_ADDR,
- .end = AU1550_PSC0_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_PSC0_INT,
- .end = AU1200_PSC0_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_PSC0_TX,
- .end = AU1200_DSCR_CMD0_PSC0_TX,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = AU1200_DSCR_CMD0_PSC0_RX,
- .end = AU1200_DSCR_CMD0_PSC0_RX,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static struct platform_device pb1200_i2c_dev = {
- .name = "au1xpsc_smbus",
- .id = 0, /* bus number */
- .num_resources = ARRAY_SIZE(au1200_psc0_res),
- .resource = au1200_psc0_res,
-};
-
-static struct resource au1200_lcd_res[] = {
- [0] = {
- .start = AU1200_LCD_PHYS_ADDR,
- .end = AU1200_LCD_PHYS_ADDR + 0x800 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_LCD_INT,
- .end = AU1200_LCD_INT,
- .flags = IORESOURCE_IRQ,
- }
-};
-
-static u64 au1200_lcd_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device au1200_lcd_dev = {
- .name = "au1200-lcd",
- .id = 0,
- .dev = {
- .dma_mask = &au1200_lcd_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(au1200_lcd_res),
- .resource = au1200_lcd_res,
-};
-
-static struct platform_device *board_platform_devices[] __initdata = {
- &ide_device,
- &smc91c111_device,
- &pb1200_i2c_dev,
- &pb1200_mmc0_dev,
- &pb1200_mmc1_dev,
- &au1200_lcd_dev,
-};
-
-static int __init board_register_devices(void)
-{
- int swapped;
-
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
- PB1200_PC0_INT, PB1200_PC0_INSERT_INT,
- /*PB1200_PC0_STSCHG_INT*/0, PB1200_PC0_EJECT_INT, 0);
-
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008000000,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008000000,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x008000000,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x008010000 - 1,
- PB1200_PC1_INT, PB1200_PC1_INSERT_INT,
- /*PB1200_PC1_STSCHG_INT*/0, PB1200_PC1_EJECT_INT, 1);
-
- swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1200_SWAPBOOT;
- db1x_register_norflash(128 * 1024 * 1024, 2, swapped);
-
- return platform_add_devices(board_platform_devices,
- ARRAY_SIZE(board_platform_devices));
-}
-device_initcall(board_register_devices);
diff --git a/arch/mips/alchemy/devboards/pb1500.c b/arch/mips/alchemy/devboards/pb1500.c
new file mode 100644
index 0000000..e7b807b
--- /dev/null
+++ b/arch/mips/alchemy/devboards/pb1500.c
@@ -0,0 +1,198 @@
+/*
+ * Pb1500 board support.
+ *
+ * Copyright (C) 2009 Manuel Lauss
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <prom.h>
+#include "platform.h"
+
+const char *get_system_type(void)
+{
+ return "PB1500";
+}
+
+void __init board_setup(void)
+{
+ u32 pin_func;
+ u32 sys_freqctrl, sys_clksrc;
+
+ bcsr_init(DB1000_BCSR_PHYS_ADDR,
+ DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
+
+ sys_clksrc = sys_freqctrl = pin_func = 0;
+ /* Set AUX clock to 12 MHz * 8 = 96 MHz */
+ au_writel(8, SYS_AUXPLL);
+ alchemy_gpio1_input_enable();
+ udelay(100);
+
+ /* GPIO201 is input for PCMCIA card detect */
+ /* GPIO203 is input for PCMCIA interrupt request */
+ alchemy_gpio_direction_input(201);
+ alchemy_gpio_direction_input(203);
+
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+
+ /* Zero and disable FREQ2 */
+ sys_freqctrl = au_readl(SYS_FREQCTRL0);
+ sys_freqctrl &= ~0xFFF00000;
+ au_writel(sys_freqctrl, SYS_FREQCTRL0);
+
+ /* zero and disable USBH/USBD clocks */
+ sys_clksrc = au_readl(SYS_CLKSRC);
+ sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
+ SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
+ au_writel(sys_clksrc, SYS_CLKSRC);
+
+ sys_freqctrl = au_readl(SYS_FREQCTRL0);
+ sys_freqctrl &= ~0xFFF00000;
+
+ sys_clksrc = au_readl(SYS_CLKSRC);
+ sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
+ SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
+
+ /* FREQ2 = aux/2 = 48 MHz */
+ sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) | SYS_FC_FE2 | SYS_FC_FS2;
+ au_writel(sys_freqctrl, SYS_FREQCTRL0);
+
+ /*
+ * Route 48MHz FREQ2 into USB Host and/or Device
+ */
+ sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MUH_BIT;
+ au_writel(sys_clksrc, SYS_CLKSRC);
+
+ pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_USB;
+ /* 2nd USB port is USB host */
+ pin_func |= SYS_PF_USB;
+ au_writel(pin_func, SYS_PINFUNC);
+#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
+
+#ifdef CONFIG_PCI
+ {
+ void __iomem *base =
+ (void __iomem *)KSEG1ADDR(AU1500_PCI_PHYS_ADDR);
+ /* Setup PCI bus controller */
+ __raw_writel(0x00003fff, base + PCI_REG_CMEM);
+ __raw_writel(0xf0000000, base + PCI_REG_MWMASK_DEV);
+ __raw_writel(0, base + PCI_REG_MWBASE_REV_CCL);
+ __raw_writel(0x02a00356, base + PCI_REG_STATCMD);
+ __raw_writel(0x00003c04, base + PCI_REG_PARAM);
+ __raw_writel(0x00000008, base + PCI_REG_MBAR);
+ wmb();
+ }
+#endif
+
+ /* Enable sys bus clock divider when IDLE state or no bus activity. */
+ au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
+
+ /* Enable the RTC if not already enabled */
+ if (!(au_readl(0xac000028) & 0x20)) {
+ printk(KERN_INFO "enabling clock ...\n");
+ au_writel((au_readl(0xac000028) | 0x20), 0xac000028);
+ }
+ /* Put the clock in BCD mode */
+ if (au_readl(0xac00002c) & 0x4) { /* reg B */
+ au_writel(au_readl(0xac00002c) & ~0x4, 0xac00002c);
+ au_sync();
+ }
+}
+
+/******************************************************************************/
+
+static int pb1500_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+ if ((slot < 12) || (slot > 13) || pin == 0)
+ return -1;
+ if (slot == 12)
+ return (pin == 1) ? AU1500_PCI_INTA : 0xff;
+ if (slot == 13) {
+ switch (pin) {
+ case 1: return AU1500_PCI_INTA;
+ case 2: return AU1500_PCI_INTB;
+ case 3: return AU1500_PCI_INTC;
+ case 4: return AU1500_PCI_INTD;
+ }
+ }
+ return -1;
+}
+
+static struct resource alchemy_pci_host_res[] = {
+ [0] = {
+ .start = AU1500_PCI_PHYS_ADDR,
+ .end = AU1500_PCI_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct alchemy_pci_platdata pb1500_pci_pd = {
+ .board_map_irq = pb1500_map_pci_irq,
+ .pci_cfg_set = PCI_CONFIG_AEN | PCI_CONFIG_R2H | PCI_CONFIG_R1H |
+ PCI_CONFIG_CH |
+#if defined(__MIPSEB__)
+ PCI_CONFIG_SIC_HWA_DAT | PCI_CONFIG_SM,
+#else
+ 0,
+#endif
+};
+
+static struct platform_device pb1500_pci_host = {
+ .dev.platform_data = &pb1500_pci_pd,
+ .name = "alchemy-pci",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
+ .resource = alchemy_pci_host_res,
+};
+
+static int __init pb1500_dev_init(void)
+{
+ int swapped;
+
+ irq_set_irq_type(AU1500_GPIO9_INT, IRQF_TRIGGER_LOW); /* CD0# */
+ irq_set_irq_type(AU1500_GPIO10_INT, IRQF_TRIGGER_LOW); /* CARD0 */
+ irq_set_irq_type(AU1500_GPIO11_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
+ irq_set_irq_type(AU1500_GPIO204_INT, IRQF_TRIGGER_HIGH);
+ irq_set_irq_type(AU1500_GPIO201_INT, IRQF_TRIGGER_LOW);
+ irq_set_irq_type(AU1500_GPIO202_INT, IRQF_TRIGGER_LOW);
+ irq_set_irq_type(AU1500_GPIO203_INT, IRQF_TRIGGER_LOW);
+ irq_set_irq_type(AU1500_GPIO205_INT, IRQF_TRIGGER_LOW);
+
+ /* PCMCIA. single socket, identical to Pb1100 */
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ AU1500_GPIO11_INT, AU1500_GPIO9_INT, /* card / insert */
+ /*AU1500_GPIO10_INT*/0, 0, 0); /* stschg / eject / id */
+
+ swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT;
+ db1x_register_norflash(64 * 1024 * 1024, 4, swapped);
+ platform_device_register(&pb1500_pci_host);
+
+ return 0;
+}
+arch_initcall(pb1500_dev_init);
diff --git a/arch/mips/alchemy/devboards/pb1500/Makefile b/arch/mips/alchemy/devboards/pb1500/Makefile
deleted file mode 100644
index e83b151..0000000
--- a/arch/mips/alchemy/devboards/pb1500/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# Copyright 2000, 2001, 2008 MontaVista Software Inc.
-# Author: MontaVista Software, Inc. <source@xxxxxxxxxx>
-#
-# Makefile for the Alchemy Semiconductor Pb1500 board.
-#
-
-obj-y := board_setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/pb1500/board_setup.c b/arch/mips/alchemy/devboards/pb1500/board_setup.c
deleted file mode 100644
index 37c1883..0000000
--- a/arch/mips/alchemy/devboards/pb1500/board_setup.c
+++ /dev/null
@@ -1,139 +0,0 @@
-/*
- * Copyright 2000, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@xxxxxxxxxx>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/delay.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-db1x00/bcsr.h>
-
-#include <prom.h>
-
-const char *get_system_type(void)
-{
- return "Alchemy Pb1500";
-}
-
-void __init board_setup(void)
-{
- u32 pin_func;
- u32 sys_freqctrl, sys_clksrc;
-
- bcsr_init(DB1000_BCSR_PHYS_ADDR,
- DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
-
- sys_clksrc = sys_freqctrl = pin_func = 0;
- /* Set AUX clock to 12 MHz * 8 = 96 MHz */
- au_writel(8, SYS_AUXPLL);
- alchemy_gpio1_input_enable();
- udelay(100);
-
- /* GPIO201 is input for PCMCIA card detect */
- /* GPIO203 is input for PCMCIA interrupt request */
- alchemy_gpio_direction_input(201);
- alchemy_gpio_direction_input(203);
-
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
-
- /* Zero and disable FREQ2 */
- sys_freqctrl = au_readl(SYS_FREQCTRL0);
- sys_freqctrl &= ~0xFFF00000;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
- /* zero and disable USBH/USBD clocks */
- sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
- SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
- au_writel(sys_clksrc, SYS_CLKSRC);
-
- sys_freqctrl = au_readl(SYS_FREQCTRL0);
- sys_freqctrl &= ~0xFFF00000;
-
- sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
- SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
-
- /* FREQ2 = aux/2 = 48 MHz */
- sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) | SYS_FC_FE2 | SYS_FC_FS2;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
- /*
- * Route 48MHz FREQ2 into USB Host and/or Device
- */
- sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MUH_BIT;
- au_writel(sys_clksrc, SYS_CLKSRC);
-
- pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_USB;
- /* 2nd USB port is USB host */
- pin_func |= SYS_PF_USB;
- au_writel(pin_func, SYS_PINFUNC);
-#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
-
-#ifdef CONFIG_PCI
- {
- void __iomem *base =
- (void __iomem *)KSEG1ADDR(AU1500_PCI_PHYS_ADDR);
- /* Setup PCI bus controller */
- __raw_writel(0x00003fff, base + PCI_REG_CMEM);
- __raw_writel(0xf0000000, base + PCI_REG_MWMASK_DEV);
- __raw_writel(0, base + PCI_REG_MWBASE_REV_CCL);
- __raw_writel(0x02a00356, base + PCI_REG_STATCMD);
- __raw_writel(0x00003c04, base + PCI_REG_PARAM);
- __raw_writel(0x00000008, base + PCI_REG_MBAR);
- wmb();
- }
-#endif
-
- /* Enable sys bus clock divider when IDLE state or no bus activity. */
- au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
-
- /* Enable the RTC if not already enabled */
- if (!(au_readl(0xac000028) & 0x20)) {
- printk(KERN_INFO "enabling clock ...\n");
- au_writel((au_readl(0xac000028) | 0x20), 0xac000028);
- }
- /* Put the clock in BCD mode */
- if (au_readl(0xac00002c) & 0x4) { /* reg B */
- au_writel(au_readl(0xac00002c) & ~0x4, 0xac00002c);
- au_sync();
- }
-}
-
-static int __init pb1500_init_irq(void)
-{
- irq_set_irq_type(AU1500_GPIO9_INT, IRQF_TRIGGER_LOW); /* CD0# */
- irq_set_irq_type(AU1500_GPIO10_INT, IRQF_TRIGGER_LOW); /* CARD0 */
- irq_set_irq_type(AU1500_GPIO11_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
- irq_set_irq_type(AU1500_GPIO204_INT, IRQF_TRIGGER_HIGH);
- irq_set_irq_type(AU1500_GPIO201_INT, IRQF_TRIGGER_LOW);
- irq_set_irq_type(AU1500_GPIO202_INT, IRQF_TRIGGER_LOW);
- irq_set_irq_type(AU1500_GPIO203_INT, IRQF_TRIGGER_LOW);
- irq_set_irq_type(AU1500_GPIO205_INT, IRQF_TRIGGER_LOW);
-
- return 0;
-}
-arch_initcall(pb1500_init_irq);
diff --git a/arch/mips/alchemy/devboards/pb1500/platform.c b/arch/mips/alchemy/devboards/pb1500/platform.c
deleted file mode 100644
index 1e52a01..0000000
--- a/arch/mips/alchemy/devboards/pb1500/platform.c
+++ /dev/null
@@ -1,94 +0,0 @@
-/*
- * Pb1500 board platform device registration
- *
- * Copyright (C) 2009 Manuel Lauss
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/dma-mapping.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-db1x00/bcsr.h>
-
-#include "../platform.h"
-
-static int pb1500_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
-{
- if ((slot < 12) || (slot > 13) || pin == 0)
- return -1;
- if (slot == 12)
- return (pin == 1) ? AU1500_PCI_INTA : 0xff;
- if (slot == 13) {
- switch (pin) {
- case 1: return AU1500_PCI_INTA;
- case 2: return AU1500_PCI_INTB;
- case 3: return AU1500_PCI_INTC;
- case 4: return AU1500_PCI_INTD;
- }
- }
- return -1;
-}
-
-static struct resource alchemy_pci_host_res[] = {
- [0] = {
- .start = AU1500_PCI_PHYS_ADDR,
- .end = AU1500_PCI_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct alchemy_pci_platdata pb1500_pci_pd = {
- .board_map_irq = pb1500_map_pci_irq,
- .pci_cfg_set = PCI_CONFIG_AEN | PCI_CONFIG_R2H | PCI_CONFIG_R1H |
- PCI_CONFIG_CH |
-#if defined(__MIPSEB__)
- PCI_CONFIG_SIC_HWA_DAT | PCI_CONFIG_SM,
-#else
- 0,
-#endif
-};
-
-static struct platform_device pb1500_pci_host = {
- .dev.platform_data = &pb1500_pci_pd,
- .name = "alchemy-pci",
- .id = 0,
- .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
- .resource = alchemy_pci_host_res,
-};
-
-static int __init pb1500_dev_init(void)
-{
- int swapped;
-
- /* PCMCIA. single socket, identical to Pb1100 */
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
- AU1500_GPIO11_INT, AU1500_GPIO9_INT, /* card / insert */
- /*AU1500_GPIO10_INT*/0, 0, 0); /* stschg / eject / id */
-
- swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT;
- db1x_register_norflash(64 * 1024 * 1024, 4, swapped);
- platform_device_register(&pb1500_pci_host);
-
- return 0;
-}
-arch_initcall(pb1500_dev_init);
diff --git a/arch/mips/alchemy/devboards/pb1550.c b/arch/mips/alchemy/devboards/pb1550.c
new file mode 100644
index 0000000..e4a00a5
--- /dev/null
+++ b/arch/mips/alchemy/devboards/pb1550.c
@@ -0,0 +1,178 @@
+/*
+ * Pb1550 board support.
+ *
+ * Copyright (C) 2009-2011 Manuel Lauss
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1xxx_dbdma.h>
+#include <asm/mach-au1x00/gpio.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include "platform.h"
+
+const char *get_system_type(void)
+{
+ return "PB1550";
+}
+
+void __init board_setup(void)
+{
+ u32 pin_func;
+
+ bcsr_init(PB1550_BCSR_PHYS_ADDR,
+ PB1550_BCSR_PHYS_ADDR + PB1550_BCSR_HEXLED_OFS);
+
+ alchemy_gpio2_enable();
+
+ /*
+ * Enable PSC1 SYNC for AC'97. Normaly done in audio driver,
+ * but it is board specific code, so put it here.
+ */
+ pin_func = au_readl(SYS_PINFUNC);
+ au_sync();
+ pin_func |= SYS_PF_MUST_BE_SET | SYS_PF_PSC1_S1;
+ au_writel(pin_func, SYS_PINFUNC);
+
+ bcsr_write(BCSR_PCMCIA, 0); /* turn off PCMCIA power */
+
+ printk(KERN_INFO "AMD Alchemy Pb1550 Board\n");
+}
+
+/******************************************************************************/
+
+static int pb1550_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+ if ((slot < 12) || (slot > 13) || pin == 0)
+ return -1;
+ if (slot == 12) {
+ switch (pin) {
+ case 1: return AU1500_PCI_INTB;
+ case 2: return AU1500_PCI_INTC;
+ case 3: return AU1500_PCI_INTD;
+ case 4: return AU1500_PCI_INTA;
+ }
+ }
+ if (slot == 13) {
+ switch (pin) {
+ case 1: return AU1500_PCI_INTA;
+ case 2: return AU1500_PCI_INTB;
+ case 3: return AU1500_PCI_INTC;
+ case 4: return AU1500_PCI_INTD;
+ }
+ }
+ return -1;
+}
+
+static struct resource alchemy_pci_host_res[] = {
+ [0] = {
+ .start = AU1500_PCI_PHYS_ADDR,
+ .end = AU1500_PCI_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct alchemy_pci_platdata pb1550_pci_pd = {
+ .board_map_irq = pb1550_map_pci_irq,
+};
+
+static struct platform_device pb1550_pci_host = {
+ .dev.platform_data = &pb1550_pci_pd,
+ .name = "alchemy-pci",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
+ .resource = alchemy_pci_host_res,
+};
+
+static struct resource au1550_psc2_res[] = {
+ [0] = {
+ .start = AU1550_PSC2_PHYS_ADDR,
+ .end = AU1550_PSC2_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1550_PSC2_INT,
+ .end = AU1550_PSC2_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1550_DSCR_CMD0_PSC2_TX,
+ .end = AU1550_DSCR_CMD0_PSC2_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1550_DSCR_CMD0_PSC2_RX,
+ .end = AU1550_DSCR_CMD0_PSC2_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device pb1550_i2c_dev = {
+ .name = "au1xpsc_smbus",
+ .id = 0, /* bus number */
+ .num_resources = ARRAY_SIZE(au1550_psc2_res),
+ .resource = au1550_psc2_res,
+};
+
+static int __init pb1550_dev_init(void)
+{
+ int swapped;
+
+ irq_set_irq_type(AU1550_GPIO0_INT, IRQF_TRIGGER_LOW);
+ irq_set_irq_type(AU1550_GPIO1_INT, IRQF_TRIGGER_LOW);
+ irq_set_irq_type(AU1550_GPIO201_205_INT, IRQF_TRIGGER_HIGH);
+
+ /* enable both PCMCIA card irqs in the shared line */
+ alchemy_gpio2_enable_int(201);
+ alchemy_gpio2_enable_int(202);
+
+ /* Pb1550, like all others, also has statuschange irqs; however they're
+ * wired up on one of the Au1550's shared GPIO201_205 line, which also
+ * services the PCMCIA card interrupts. So we ignore statuschange and
+ * use the GPIO201_205 exclusively for card interrupts, since a) pcmcia
+ * drivers are used to shared irqs and b) statuschange isn't really use-
+ * ful anyway.
+ */
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ AU1550_GPIO201_205_INT, AU1550_GPIO0_INT, 0, 0, 0);
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008000000,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008000000,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x008000000,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x008010000 - 1,
+ AU1550_GPIO201_205_INT, AU1550_GPIO1_INT, 0, 0, 1);
+
+ swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_PB1550_SWAPBOOT;
+ db1x_register_norflash(128 * 1024 * 1024, 4, swapped);
+ platform_device_register(&pb1550_pci_host);
+ platform_device_register(&pb1550_i2c_dev);
+
+ return 0;
+}
+arch_initcall(pb1550_dev_init);
diff --git a/arch/mips/alchemy/devboards/pb1550/Makefile b/arch/mips/alchemy/devboards/pb1550/Makefile
deleted file mode 100644
index 9661b6e..0000000
--- a/arch/mips/alchemy/devboards/pb1550/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# Copyright 2000, 2008 MontaVista Software Inc.
-# Author: MontaVista Software, Inc. <source@xxxxxxxxxx>
-#
-# Makefile for the Alchemy Semiconductor Pb1550 board.
-#
-
-obj-y := board_setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/pb1550/board_setup.c b/arch/mips/alchemy/devboards/pb1550/board_setup.c
deleted file mode 100644
index 0f62d1e..0000000
--- a/arch/mips/alchemy/devboards/pb1550/board_setup.c
+++ /dev/null
@@ -1,80 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * Alchemy Pb1550 board setup.
- *
- * Copyright 2000, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@xxxxxxxxxx>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/interrupt.h>
-
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-pb1x00/pb1550.h>
-#include <asm/mach-db1x00/bcsr.h>
-#include <asm/mach-au1x00/gpio.h>
-
-#include <prom.h>
-
-const char *get_system_type(void)
-{
- return "Alchemy Pb1550";
-}
-
-void __init board_setup(void)
-{
- u32 pin_func;
-
- bcsr_init(PB1550_BCSR_PHYS_ADDR,
- PB1550_BCSR_PHYS_ADDR + PB1550_BCSR_HEXLED_OFS);
-
- alchemy_gpio2_enable();
-
- /*
- * Enable PSC1 SYNC for AC'97. Normaly done in audio driver,
- * but it is board specific code, so put it here.
- */
- pin_func = au_readl(SYS_PINFUNC);
- au_sync();
- pin_func |= SYS_PF_MUST_BE_SET | SYS_PF_PSC1_S1;
- au_writel(pin_func, SYS_PINFUNC);
-
- bcsr_write(BCSR_PCMCIA, 0); /* turn off PCMCIA power */
-
- printk(KERN_INFO "AMD Alchemy Pb1550 Board\n");
-}
-
-static int __init pb1550_init_irq(void)
-{
- irq_set_irq_type(AU1550_GPIO0_INT, IRQF_TRIGGER_LOW);
- irq_set_irq_type(AU1550_GPIO1_INT, IRQF_TRIGGER_LOW);
- irq_set_irq_type(AU1550_GPIO201_205_INT, IRQF_TRIGGER_HIGH);
-
- /* enable both PCMCIA card irqs in the shared line */
- alchemy_gpio2_enable_int(201);
- alchemy_gpio2_enable_int(202);
-
- return 0;
-}
-arch_initcall(pb1550_init_irq);
diff --git a/arch/mips/alchemy/devboards/pb1550/platform.c b/arch/mips/alchemy/devboards/pb1550/platform.c
deleted file mode 100644
index a4604b8..0000000
--- a/arch/mips/alchemy/devboards/pb1550/platform.c
+++ /dev/null
@@ -1,140 +0,0 @@
-/*
- * Pb1550 board platform device registration
- *
- * Copyright (C) 2009 Manuel Lauss
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/dma-mapping.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-au1x00/au1xxx_dbdma.h>
-#include <asm/mach-pb1x00/pb1550.h>
-#include <asm/mach-db1x00/bcsr.h>
-
-#include "../platform.h"
-
-static int pb1550_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
-{
- if ((slot < 12) || (slot > 13) || pin == 0)
- return -1;
- if (slot == 12) {
- switch (pin) {
- case 1: return AU1500_PCI_INTB;
- case 2: return AU1500_PCI_INTC;
- case 3: return AU1500_PCI_INTD;
- case 4: return AU1500_PCI_INTA;
- }
- }
- if (slot == 13) {
- switch (pin) {
- case 1: return AU1500_PCI_INTA;
- case 2: return AU1500_PCI_INTB;
- case 3: return AU1500_PCI_INTC;
- case 4: return AU1500_PCI_INTD;
- }
- }
- return -1;
-}
-
-static struct resource alchemy_pci_host_res[] = {
- [0] = {
- .start = AU1500_PCI_PHYS_ADDR,
- .end = AU1500_PCI_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct alchemy_pci_platdata pb1550_pci_pd = {
- .board_map_irq = pb1550_map_pci_irq,
-};
-
-static struct platform_device pb1550_pci_host = {
- .dev.platform_data = &pb1550_pci_pd,
- .name = "alchemy-pci",
- .id = 0,
- .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
- .resource = alchemy_pci_host_res,
-};
-
-static struct resource au1550_psc2_res[] = {
- [0] = {
- .start = AU1550_PSC2_PHYS_ADDR,
- .end = AU1550_PSC2_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1550_PSC2_INT,
- .end = AU1550_PSC2_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = AU1550_DSCR_CMD0_PSC2_TX,
- .end = AU1550_DSCR_CMD0_PSC2_TX,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = AU1550_DSCR_CMD0_PSC2_RX,
- .end = AU1550_DSCR_CMD0_PSC2_RX,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static struct platform_device pb1550_i2c_dev = {
- .name = "au1xpsc_smbus",
- .id = 0, /* bus number */
- .num_resources = ARRAY_SIZE(au1550_psc2_res),
- .resource = au1550_psc2_res,
-};
-
-static int __init pb1550_dev_init(void)
-{
- int swapped;
-
- /* Pb1550, like all others, also has statuschange irqs; however they're
- * wired up on one of the Au1550's shared GPIO201_205 line, which also
- * services the PCMCIA card interrupts. So we ignore statuschange and
- * use the GPIO201_205 exclusively for card interrupts, since a) pcmcia
- * drivers are used to shared irqs and b) statuschange isn't really use-
- * ful anyway.
- */
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
- AU1550_GPIO201_205_INT, AU1550_GPIO0_INT, 0, 0, 0);
-
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008000000,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008000000,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x008000000,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x008010000 - 1,
- AU1550_GPIO201_205_INT, AU1550_GPIO1_INT, 0, 0, 1);
-
- swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_PB1550_SWAPBOOT;
- db1x_register_norflash(128 * 1024 * 1024, 4, swapped);
- platform_device_register(&pb1550_pci_host);
- platform_device_register(&pb1550_i2c_dev);
-
- return 0;
-}
-arch_initcall(pb1550_dev_init);
--
1.7.7.1
