Hi All, To further to add on to info and to bring one point to notice, I had build my kernel with SDE toolset (gcc version 3.4.4 mipssde-6.02.03-20050629) and binutils 2.15.94 (for e.g., GNU objcopy 2.15.94 mipssde-6.02.03-20050629) It is mentioned on SDE site, that the SDE package will only install compiler but I found that it installed binutils package also. I am going to try with binutils 2.16 and lets see if it helps. Thanks and Regards, Shyamal On 4/27/06, Shyamal Sadanshio <shyamal.sadanshio@xxxxxxxxx> wrote: > Hi Nigel, Ralf, > > Yes, I'm using the default config with option set to R1 processor. > I am using NFS filesystem and loading the image through ethernet using > minicom. > > Here's the sequence: > Start NFS service > load tftp://192.168.2.237/vmlinux.srec > go .nfsroot=192.168.2.237/linux/mipsel ip=192.168.2.24 > > Here's the YAMON boot message: > NUX started... > Config serial console: console=ttyS0,38400n8r > > * Exception (user) : Breakpoint * > CAUSE = 0x10808024 STATUS = 0x10002c02 > CONFIG = 0x80030083 CONFIG1 = 0x1e9b4d8a > EPC = 0x80549830 ERROREPC = 0x80029cf4 > BADVADDR = 0xffffffff HI = 0x00000000 > LO = 0x04000000 > > $ 0(zr):0x00000000 $ 8(t0):0x804c18dc $16(s0):0x8056d0b8 > $24(t8):0x804bfddd > $ 1(at):0x10002c00 $ 9(t1):0x0000007f $17(s1):0x80490000 > $25(t9):0x80571f77 > $ 2(v0):0xffffffff $10(t2):0x00000040 $18(s2):0x80570000 > $26(k0):0x00000000 > $ 3(v1):0xffffffe1 $11(t3):0x80570000 $19(s3):0x8056d0bc > $27(k1):0x00000000 > $ 4(a0):0x00000040 $12(t4):0x80570000 $20(s4):0x00000000 > $28(gp):0x804be000 > $ 5(a1):0x00000000 $13(t5):0x00000000 $21(s5):0x804bffc0 > $29(sp):0x804bff50 > $ 6(a2):0x08000000 $14(t6):0x80571b91 $22(s6):0x00000000 > $30(s8):0x8009e0c0 > $ 7(a3):0xbbe00000 $15(t7):0x00000010 $23(s7):0x00000000 > $31(ra):0x8054b22c > > I have attached my config file along with this mail. > > Thanks and Regards, > Shyamal > > > On 4/27/06, Ralf Baechle <ralf@xxxxxxxxxxxxxx> wrote: > > On Wed, Apr 26, 2006 at 02:15:29PM +0530, Shyamal Sadanshio wrote: > > > > > I am facing boot problem with the Malta specific 2.6.12-rc6 kernel. > > > The kernel is not booting up on our Malta 4kc development board. > > > I do not see any error messages on the minicom window. > > > > In case you're using the default configuration file, it's set to > > MIPS32R1 but the 4Kc is an R1 processor. Are you sure you really have a > > 4Kc and not a 4Kec? The latter is an R2 processor. > > > > Ralf > > > >
