On Sun, 19 Jan 2003, Yuliy Minchev wrote: I have to update the case. I've tried to move /dev/sdb3 to the end of the hard drive. After this, I recreated sdb45 on the same size free space, but starting at lower cyl (again after 1024). And it works. Systems does not hang. I can run pvcreate, vgextend and so on... After this I deleted again disk partition sdb45 and move /dev/sdb3 on its inital place. I recreated again sdb45 and again system hangs. This whole lot looks to strange to me :( It should be like this. As long as I know - position on hard disk is not important at all. > On Sun, 19 Jan 2003, Steven Lembark wrote: > > > > > > > -- Yuliy Minchev <yuliy@mobiltel.bg> > > > > > On Sat, 18 Jan 2003, Steven Lembark wrote: > > > > > >> > > >> > I have installed Red Hat Linux 8.0. I've made volume group (rootvg) > > >> > from /dev/md1 (which is raid1). I've put my /boot on /dev/md0. > > >> > > > >> > As you already have noticed - I have two disks. > > >> > After installation I'm making new partiotion /dev/sdb5 i.e. > > >> > And if I change its to type to 8e after reboot kernel panics. > > >> > If I change type of this partition to something different - the system > > >> > boots fine. > > >> > > > >> > I cannot understand where can be the problem. > > >> > I have to say that I made the same configuration on this machine and > > >> > everything was ok. But now I cannot see any difference. > > >> > > >> sdb5 => sub-partition. Are you accidentally carving out > > >> a piece of an existing PV? For example, if you had partitioned > > >> the disk into /dev/sdb[1234] when it was built with sdb4 taking > > >> up most of the device as 8e (i.e., for LVM), then adding sdb5 > > >> w/in the area of sdb4 would certianly break things -- and scramble > > >> your LV's during pvcreate on the new partition. > > > > > > I have > > > > > > /dev/sdb1 /boot (member of md0,raid1) > > > /dev/sdb1 member of md1, raid1, on md1 is my volume group > > > /dev/sdb3 fat32 > > > /dev/sbd4 extend partion > > > /dev/sdb5 is defined as 8e within sdb4 > > > > > > Sorry, but I did not understand your point :( > > > > One thing people have zapped themselves with in the past > > is something like: > > > > /dev/sdb4 == one partition > > /dev/sdb5 == another partition whose space is > > contained w/in /dev/sdb4 > > > > pvcreate -ff /dev/sdb4; > > vgcreate vg00 /dev/sdb4; > > lvcretate ... vg00; > > > > <later in time> > > > > pvcreate -ff /dev/sdb5; > > vgcreate vg01 /dev/sdb5; > > lvcreate ... vg01; > > > > at this point the creation of vg01 has overwritten > > data in vg00 becuase the partition /dev/sda5 uses > > disk realestate contained within /dev/sda4. This is > > a matter purely caused by having moultiple partitions > > w/in the same spindle. > > > > That is why I wondered if you had made the mistake > > of creating a partition w/in an already-existing > > partition which was used as a PV at the time when > > your new partition was created and used. > > No, no... > The case is not like this. There is no such overlapping here. > > I created my volume group during RH8 installation. > After that I manually created /dev/sdb4 and within /dev/sbd5 with fdisk. > And when I change the type of /dev/sbd5 to 8e in order to be able > to run pvcreate ot it and to add it to my volume groups - the > systems hangs during kernel loading. In fact, the system stops to > recognise my volume group. That's why it hangs. > > yuliy > > > > > > > > > > -- > > Steven Lembark 2930 W. Palmer > > Workhorse Computing Chicago, IL 60647 > > +1 773 252 1080 > > > > _______________________________________________ > > linux-lvm mailing list > > linux-lvm@sistina.com > > http://lists.sistina.com/mailman/listinfo/linux-lvm > > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ > > > > -- Yuliy Minchev, UNIX Administrator _______________________________________________ linux-lvm mailing list linux-lvm@sistina.com http://lists.sistina.com/mailman/listinfo/linux-lvm read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/
