Small Update
...
In addition i searched drivers/hwmon/it87.c in order to find the
patched code from kernel 4.5-rc5.
Unfortunately i found no code changes from Patch v3 (i tested about 5
patches).
Should it not be patched within 4.5-rc1 or do i miss here something?
Does it say anywhere that the patches were reviewed and/or accepted
for upstream integration ?
Problem is that there is hardly anyone willing to review hwmon kernel
patches nowadays, meaning they have to go in unreviewed or not at all.
Given the complexity and scope of the series, I don't want to just push
the patches into the upstream kernel without review. With that in mind,
it may take a while for the code to be upstream.
I see. You wrote that it should go up with rc-1, so i thought it is
already there, my mistake.
Second question
Is it possible to take your code from github to patch/replace it in
another kernel, like 4.3 / 4.4 ?
Yes, that should be possible. I have been running it on earlier kernels
myself.
With GitHub module code for it87 chip's and a boot parameter
"acpi_enforce_resources=lax"
i was able to load it.
it8628-isa-0a40
Adapter: ISA adapter
in0: +0.43 V (min = +0.00 V, max = +3.06 V) <--- seems
to be VCore, tested with cpuBurn
in1: +2.04 V (min = +0.00 V, max = +3.06 V)
in2: +2.00 V (min = +0.00 V, max = +3.06 V)
in3: +2.04 V (min = +0.00 V, max = +3.06 V)
in4: +0.01 V (min = +0.00 V, max = +3.06 V)
in5: +1.07 V (min = +0.00 V, max = +3.06 V)
in6: +1.20 V (min = +0.00 V, max = +3.06 V) <--- could
be RAM Voltage
3VSB: +3.36 V (min = +0.00 V, max = +6.12 V)
Vbat: +3.17 V <--- Battery Voltage from EFI, really?!
fan1: 0 RPM (min = 0 RPM) <--- CPU_FAN not connected
fan2: 2280 RPM (min = 0 RPM) <--- CPU_OPT (my H80i pump)
fan3: 1078 RPM (min = 0 RPM) <--- SYS_FAN3 or 2 (radiator fan)
fan4: 0 RPM (min = 0 RPM) <--- SYS_FAN1 not connected
fan5: 1819 RPM (min = 0 RPM) <--- SYS_FAN2 or 3 (radiator fan #2)
temp1: +43.0°C (low = +127.0°C, high = +127.0°C) sensor =
thermistor
temp2: -8.0°C (low = +127.0°C, high = +127.0°C) sensor =
thermistor
temp3: +22.0°C (low = +127.0°C, high = +127.0°C) sensor =
Intel PECI
intrusion0: OK <--- Nice, i have to check where and how
to use that
Kernel 4.3.5 with Debian Testing (Stretch)
sensors version 3.4.0 with libsensors version 3.4.0
fancontrol 3.4.0-2
I'll try to get that names step by step. Further i tried fancontrol, i
got funny stuff with fan5.
It seems to be that PWM values from fan5 are inverted.
Following fancontrol setting stops all fans.
# Configuration file generated by pwmconfig, changes will be lost
INTERVAL=10
DEVPATH=hwmon2=devices/platform/it87.2624
DEVNAME=hwmon2=it8628
FCTEMPS=hwmon2/pwm5=hwmon2/temp3_input hwmon2/pwm3=hwmon2/temp3_input
FCFANS=hwmon2/pwm5=hwmon2/fan5_input hwmon2/pwm3=hwmon2/fan3_input
MINTEMP=hwmon2/pwm5=20 hwmon2/pwm3=20
MAXTEMP=hwmon2/pwm5=60 hwmon2/pwm3=60
MINSTOP=hwmon2/pwm3=1 hwmon2/pwm5=254
MINSTART=hwmon2/pwm3=1 hwmon2/pwm5=255
MINPWM=hwmon2/pwm3=0 hwmon2/pwm5=254
MAXPWM=hwmon2/pwm3=2 hwmon2/pwm5=255
I tried some different EFI settings with system fans (Silent, Normal,
PWM per degree) without
any changes. Fan3 works out of the box. I will check all other fans soon.
Any idea how to fix that?
Uwe
_______________________________________________
lm-sensors mailing list
lm-sensors@xxxxxxxxxxxxxx
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
