On Wed, Dec 17, 2014 at 12:59:38PM -0500, Sean O'Brien wrote: > Thanks Guenter. Unfortunately I dont see the adapter in the output. I had to load the i2c-dev driver manually and the output is as follows: > $ sudo i2cdetect -li2c-0 i2c Radeon i2c bit bus DVI_DDC I2C adapteri2c-1 i2c Radeon i2c bit bus VGA_DDC I2C adapteri2c-2 i2c Radeon i2c bit bus MONID I2C adapteri2c-3 i2c Radeon i2c bit bus CRT2_DDC I2C adapter > In general, please don't top-post. Also, your output seems to be messed up. Do you use Outlook ? Just wondering. Anyway, guess that explains why you don't see the chip ;-). Wonder why you see it with sensors-detect, though. Try "sudo modprobe i2c-i801". Thanks, Guenter > > Date: Wed, 17 Dec 2014 09:40:24 -0800 > > From: linux@xxxxxxxxxxxx > > To: sean451@xxxxxxxxxxx > > CC: jdelvare@xxxxxxx; lm-sensors@xxxxxxxxxxxxxx > > Subject: Re: Supermicro X7DBU configuration > > > > On Wed, Dec 17, 2014 at 11:54:24AM -0500, Sean O'Brien wrote: > > > Thanks for the help guys. > > > The driver is loaded. It is placed into /etc/modules by a run of sensor-detect, so it sees it. It shows up in the output of lsmod and a replace of the module using modprobe doesn't show any errors when loading it. However, as you point out, it doesn't show up in the output of the sensors commands (after running sensors -s also). Perhaps this is also and issue with the /etc/sensors3.conf files not having the appropriate entries for this board? The entry in there for this chip is as follows: > > > chip "w83793-*" > > > label in0 "VcoreA" label in1 "VcoreB" label in7 "+5V" label in8 "5VSB" label in9 "Vbat" > > > set in7_min 5.0 * 0.90 set in7_max 5.0 * 1.10 set in8_min 5.0 * 0.90 set in8_max 5.0 * 1.10 set in9_min 3.0 * 0.90 set in9_max 3.0 * 1.10 > > > > > > > The configuration file should not cause the chip to disappear completely. > > > > Can you provide the output of i2cdump for the w83793 ? i2cdetect -l should show > > you which bus it is on after loading the 2ic-dev driver; it is the i801 adapter. > > Command would be "sudo i2cdump <bus> 0x2f". > > > > > Btw. I found the machine doesn't have the IPMI board fitted, so no go there. > > > Thanks again. > > > > > sensors-detect reports the IPMI BMC, though, so I would assume it is there. > > Maybe you refer to the ipmi ethernet board ? > > > > Thanks, > > Guenter > > > > > > Date: Wed, 17 Dec 2014 08:27:12 -0800 > > > > From: linux@xxxxxxxxxxxx > > > > To: jdelvare@xxxxxxx > > > > CC: sean451@xxxxxxxxxxx; lm-sensors@xxxxxxxxxxxxxx > > > > Subject: Re: Supermicro X7DBU configuration > > > > > > > > On Wed, Dec 17, 2014 at 04:47:58PM +0100, Jean Delvare wrote: > > > > > Le Wednesday 17 December 2014 à 06:43 -0800, Guenter Roeck a écrit : > > > > > > On 12/17/2014 02:08 AM, Jean Delvare wrote: > > > > > > > This chip is missing from the output of "sensors" below. You need to > > > > > > > figure out why. Is the w83793 kernel module available on your system? > > > > > > > Is it loaded? If not, what happens if you try to load it manually? Any > > > > > > > error message in the kernel log? The fans are certainly connected to > > > > > > > that chip. > > > > > > > > > > > > Hardware monitoring might be disabled for this chip. I have seen this > > > > > > with other Supermicro boards; on mine, for example, they use the second > > > > > > SuperIO chip only for additional serial ports. The kernel log might > > > > > > give a hint if that is the case. > > > > > > > > > > I doubt this is the case here, as the W83793G is a dedicated hardware > > > > > monitoring chip. There's no point in putting it on the board if they > > > > > don't use the feature. > > > > > > > > > > > Another option might be that the missing chip is the one used for hardware > > > > > > monitoring but its register space is reserved by ACPI. That would explain > > > > > > why the chip listed below doesn't report much useful data. Again, the > > > > > > kernel log should give a hint. > > > > > > > > > > I don't think this can happen for an SMBus device. If the SMBus > > > > > controller had an ACPI I/O resource conflict, sensors-detect would not > > > > > have been able to scan it. And there is no notion of I2C/SMBus resource > > > > > space in ACPI. > > > > > > > > > Good point. Maybe the w83793 driver is simply not loaded. > > > > > > > > Guenter > > > > _______________________________________________ lm-sensors mailing list lm-sensors@xxxxxxxxxxxxxx http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
