Hi Mathias, On Mon, 13 Jan 2014 21:49:13 +0100, Mathias Gerber wrote: > -----BEGIN PGP SIGNED MESSAGE----- > Hash: SHA1 > > Hi Folks > > Finally I could demystify most of the sensor values for this mainboard. > My configuration file is attached to this email. > > Not clear is the temp1 reading. Should be PCH temp AFAIK. > But here I read most of the time 32°C or sometimes 33°C. Did you compare with what the BIOS says? It shows only two temperature AFAIK, CPU and M/B. I would bet that temp1 actually us the M/B temperature and temp2 isn't wired (25°C is the "neutral" temperature of thermistor setups typically.) > chip "acpitz-virtual-0" > ignore temp1 # stays always at 27.8°C > ignore temp2 # dito > > chip "it8728-*" > > label in0 "0: CPU Vtt" I've dropped all the prefixes in voltage labels. What makes you think this is Vtt and not Vcore? Almost all boards have Vcore on in0. > set in0_min 1.02 # I'm liberal with these, 2-3% tops > set in0_max 1.08 # after that, cpu gets very unstable > > label in1 "1: +3.3V" > set in1_min 3.3 * 0.95 # Some boards including GA-H67MA-UD2H > set in1_max 3.3 * 1.05 # don't have 3.3V voltage reading > compute in1 1.649*@,@/1.649 # multipliers provided by Martin Malik author of hwinfo Couldn't you figure it out from the BIOS? > label in2 "2: +12V" > set in2_min 12 * 0.95 > set in2_max 12 * 1.05 > compute in2 @ * (72/12), @ / (72/12) #mg,15.05.13 > > label in3 "3: +5V" > set in3_min 5 * 0.95 > set in3_max 5 * 1.05 > compute in3 2.5*@,@/2.5 > > label in4 "4: Vaxg" # Voltage used by the video controller embedded inside the CPU > set in4_min 0.4 > set in4_max 1.4 > > label in5 "5: Vcore" > set in5_min 0.825 * 0.95 > set in5_max 1.425 * 1.05 > > label in6 "6: Vdram" > set in6_min 1.5 * 0.95 # adjust these, 1.35 for LVDDR3 > set in6_max 1.5 * 1.05 # 1.5V is recommended, 1.65 tops > > label in7 "7: 3VSB" > set in7_min 3.00 * 0.95 > set in7_max 3.00 * 1.05 3VSB is normally 3.3V so these limits look wrong. Does the it87 driver say anything about voltage mapping when you load it? If in7 us 3VSB it should already be labeled properly. > > label in8 "8: Vbat" > set in8_min 3.0 * 0.90 > set in8_max 3.0 * 1.10 > > ### fan > > label fan1 "CPU fan" > set fan1_min 700 > > ignore fan2 # comment if connected > label fan2 "Sys1 fan" > set fan2_min 0 > > label fan3 "Sys2 fan" > set fan3_min 200 > > label fan4 "Sys3 fan" > set fan4_min 200 > > ignore fan5 # comment if connected > label fan5 "Sys4 fan" > set fan5_min 0 > > ### temperatures > > label temp1 "PCH temp??" # shows always 33°C > set temp1_min 10 > set temp1_max 60 > > ignore temp2 > label temp2 "MB temp??" # shows always 25°C > set temp2_min 0 > set temp2_max 60 > > label temp3 "CPU temp" > set temp3_min 10 > set temp3_max 85 > > ignore intrusion0 # activate if in use Current version of the configuration file is here: http://www.lm-sensors.org/wiki/Configurations/Gigabyte/Z77-D3H Thanks for your contribution. -- Jean Delvare Suse L3 Support _______________________________________________ lm-sensors mailing list lm-sensors@xxxxxxxxxxxxxx http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
