-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi Folks Finally I could demystify most of the sensor values for this mainboard. My configuration file is attached to this email. Not clear is the temp1 reading. Should be PCH temp AFAIK. But here I read most of the time 32°C or sometimes 33°C. - -- kind regards mathias -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.11 (GNU/Linux) Comment: Using GnuPG with Thunderbird - http://www.enigmail.net/ iEYEARECAAYFAlLUUUMACgkQnfTEjDUZ2fME0wCcCFL+MOQtiNi4Yhj+BRlwPvYQ X28AoLi9YyXl+bqqr0EfBasJ96A+GMc+ =FrNz -----END PGP SIGNATURE-----
chip "acpitz-virtual-0"
ignore temp1 # stays always at 27.8°C
ignore temp2 # dito
chip "it8728-*"
label in0 "0: CPU Vtt"
set in0_min 1.02 # I'm liberal with these, 2-3% tops
set in0_max 1.08 # after that, cpu gets very unstable
label in1 "1: +3.3V"
set in1_min 3.3 * 0.95 # Some boards including GA-H67MA-UD2H
set in1_max 3.3 * 1.05 # don't have 3.3V voltage reading
compute in1 1.649*@,@/1.649 # multipliers provided by Martin Malik author of hwinfo
label in2 "2: +12V"
set in2_min 12 * 0.95
set in2_max 12 * 1.05
compute in2 @ * (72/12), @ / (72/12) #mg,15.05.13
label in3 "3: +5V"
set in3_min 5 * 0.95
set in3_max 5 * 1.05
compute in3 2.5*@,@/2.5
label in4 "4: Vaxg" # Voltage used by the video controller embedded inside the CPU
set in4_min 0.4
set in4_max 1.4
label in5 "5: Vcore"
set in5_min 0.825 * 0.95
set in5_max 1.425 * 1.05
label in6 "6: Vdram"
set in6_min 1.5 * 0.95 # adjust these, 1.35 for LVDDR3
set in6_max 1.5 * 1.05 # 1.5V is recommended, 1.65 tops
label in7 "7: 3VSB"
set in7_min 3.00 * 0.95
set in7_max 3.00 * 1.05
label in8 "8: Vbat"
set in8_min 3.0 * 0.90
set in8_max 3.0 * 1.10
### fan
label fan1 "CPU fan"
set fan1_min 700
ignore fan2 # comment if connected
label fan2 "Sys1 fan"
set fan2_min 0
label fan3 "Sys2 fan"
set fan3_min 200
label fan4 "Sys3 fan"
set fan4_min 200
ignore fan5 # comment if connected
label fan5 "Sys4 fan"
set fan5_min 0
### temperatures
label temp1 "PCH temp??" # shows always 33°C
set temp1_min 10
set temp1_max 60
ignore temp2
label temp2 "MB temp??" # shows always 25°C
set temp2_min 0
set temp2_max 60
label temp3 "CPU temp"
set temp3_min 10
set temp3_max 85
ignore intrusion0 # activate if in use
Attachment:
ga-z77-d3h.conf.sig
Description: Binary data
_______________________________________________ lm-sensors mailing list lm-sensors@xxxxxxxxxxxxxx http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
