Hello everybody, I have no Trac account, but would like to place configuration example for Gigabyte motherboards models: GA-A870-UD3, GA-A870-USB3. Provided configuration was originally found by another guy in his post(http://www.spinics.net/lists/lm-sensors/msg32751.html) for GA-A870-UD3 model, but I tested this configuration on my GA-A870-USB3 and it works pretty good as well. Here is an exact configuration: # libsensors3 configuration file for the Gigabyte GA-870A-UD3 rev 3.0 # based on configuration file for the Gigabyte GA-790XTA-UD4 from Wiki with modifications. # 2011-06-16 Gary Myers <gary@xxxxxxxxxxxxxx> # Updates welcome. # CPU sensor chip "k10temp-*" label temp1 "CPU Temp (K10)" # Set for gnome-sensors-applet. # See second CPU temp below. # Motherboard sensors chip "it8720-isa-*" ### Voltages label in0 "Vcore" label in1 "DDR3 1.5V" # as labelled in the BIOS. label in2 "+3.3V" label in3 "+5V" # Not shown in BIOS. label in4 "+12V" ignore in5 # Ambiguous - ignoring. ignore in6 # Ambiguous - ignoring. label in7 "5VSB" # Not shown in BIOS. label in8 "Vbat" # Not shown in BIOS. ignore cpu0_vid # "Vcore", "DDR3 1.5V", "+3.3V" and "Vbat" are connected directly, so no compute # line is needed for these. +5V and 5VSB are internal so we use the # standard scaling factor. Scaling for +12V is apparently not standard, # factor 3.963 is guessed from BIOS and EasyTune values (3.943 was # another candidate.) compute in3 @ * (6.8/10+1), @ / (6.8/10+1) compute in4 @ * 3.963, @ / 3.963 compute in7 @ * (6.8/10+1), @ / (6.8/10+1) # The BIOS will not set any limit for voltages. set in0_min 0.825 * 0.95 set in0_max 1.425 * 1.05 set in1_min 1.5 * 0.95 set in1_max 1.5 * 1.05 set in2_min 3.3 * 0.95 set in2_max 3.3 * 1.05 set in3_min 5 * 0.95 set in3_max 5 * 1.05 set in4_min 12 * 0.95 set in4_max 12 * 1.05 set in7_min 5 * 0.95 set in7_max 5 * 1.05 ### Temperatures label temp1 "System Temp" # This sensor appears to be around or inside the ITE8720F chip. # The temperature drops if the chip and board area are cooled with # freezer spray. This sensor may be over-reading! # Adjustment applied to match internal case thermal sensor from my Antec P160. compute temp1 (@ -20), (@ + 20) set temp1_min 0 set temp1_max 50 # Tropical ambient max plus a bit label temp2 "CPU Temp" # This sensor can show 2 degrees difference to the K10 sensor. # The end user can choose which one they prefer. set temp2_min 0 set temp2_max 70 # Set to match your BIOS "CPU Warning Temperature" ignore temp3 # No idea what this sensor is for. It always shows # +78 deg C regardless of BIOS settings. ### Fans # Label based on motherboard connectors. label fan1 "CPU Fan" # M/B label: CPU_FAN (4-pin - near ATX 12V) label fan5 "Power Fan" # M/B label: PWR_FAN (3-pin - near ATX) label fan2 "System Fan 1" # M/B label: SYS_FAN1 (4-pin - near F_PANEL) label fan3 "System Fan 2" # M/B label: SYS_FAN2 (3-pin - near SATA3_4) # Minimum fan speeds. # Comment/un-comment fan headers you are using if you want alarms. set fan1_min 300 # CPU Fan set fan5_min 300 # Power Fan #set fan2_min 300 # System Fan 1 set fan3_min 300 # System Fan 2 -- ________________________________________________________________________ Kind regards, Zeke Fast _______________________________________________ lm-sensors mailing list lm-sensors@xxxxxxxxxxxxxx http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
