On 10/11/2012 03:33 AM, Guenter Roeck wrote: > Ok, then I guess it is more likely that the change was triggered by the BIOS > update. Interesting. Attached is a config file for Intel DQ67SW boards with newer BIOSes. -- ======================================================================== Ian Pilcher arequipeno@xxxxxxxxx Sometimes there's nothing left to do but crash and burn...or die trying. ========================================================================
################################################################################ # # # lm_sensors configuration for Intel DQ67SW (with newer BIOS) # # NOTES: # # Temperature input mappings were changed by a BIOS update # between SWQ6710H.86A.0050.2011.0401.1409 (01-Apr-2011) and # SWQ6710H.86A.0065.2012.0917.1519 (17-Sep-2012). # # Minimum and maximum values are the defaults from BIOS version # SWQ6710H.86A.0065.2012.0917.1519 (17-Sep-2012). # # Intel Desktop Utilities 3.2.3.052 appears to get its default # values from the BIOS. # # "FRONT" and "REAR" fan labels correspond to the motherboard # headers, but not necessarily the actual fan locations. # # Minimum fan RPMs should be adjusted to reflect the behavior of # the installed fans. # # "Memory DIMM Temperature" is presumably measured by a diode # somewhere in the vicinity of the DIMM slots; "System Temperature # might be a better name. If this is correct, 90 degrees seems # like an extremely high threshhold for this reading. # # All hysteresis values are set to 75 degrees, which seems to be # the default for the chip/driver. # # ################################################################################ chip "nct6775-*" ignore cpu0_vid ######################################################################## # # Voltages # ######################################################################## # # Processor Vcc # label in0 "VCORE" set in0_min 0.2 set in0_max 1.6 # # +12 Volts # label in1 "+12V" compute in1 16*@, @/16 set in1_min 10.8 set in1_max 13.2 # # AVCC(?) - Not shown in BIOS or IDU; min/max taken from +3.3V # label in2 "AVCC" set in2_min 3.1 set in2_max 3.5 # # +3.3 Volts # label in3 "+3.3V" set in3_min 3.1 set in3_max 3.5 # # +5 Volts # label in4 "+5V" compute in4 4*@, @/4 set in4_min 4.7 set in4_max 5.3 # # Memory Vcc # label in5 "+1.5V" set in5_min 1.4 set in5_max 1.6 # # PCH Vcc # label in6 "PCH" set in6_min 0.6 set in6_max 1.6 # # +3.3 Volt Standby # label in7 "VSB" set in7_min 3.0 set in7_max 3.6 # # VBAT(?) - Not shown in BIOS or IDU; min/max taken from old BIOS # label in8 "VBAT" #set in8_min 2.7 #set in8_max 3.3 ######################################################################## # # Fans # ######################################################################## ignore fan4 # # Chassis Inlet Fan # label fan1 "FRONT" set fan1_min 250 # from IDU (BIOS does not set) # # Processor Fan # label fan2 "CPU" set fan2_min 250 # from IDU (BIOS does not set) # # Chassis Outlet Fan # label fan3 "REAR" set fan3_min 250 # from IDU (BIOS does not set) ######################################################################## # # Temperatures # ######################################################################## ignore temp3 ignore temp8 # # Memory DIMM Temperature # label temp1 "DIMM" set temp1_max 90 set temp1_max_hyst 75 # # VR Temperature # label temp2 "VR" set temp2_max 90 set temp2_max_hyst 75 # # Processor Temperature # label temp6 "CPU" set temp6_max 99 set temp6_max_hyst 75 # # PCH Temperature # label temp7 "PCH" set temp7_max 114 set temp7_max_hyst 75
_______________________________________________ lm-sensors mailing list lm-sensors@xxxxxxxxxxxxxx http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
