Juerg Haefliger wrote: > Simon, > > Could you run sensors-detect and post the output? > Here you go: # sensors-detect # sensors-detect revision 4348 (2007-03-18 02:45:21 -0700) This program will help you determine which kernel modules you need to load to use lm_sensors most effectively. It is generally safe and recommended to accept the default answers to all questions, unless you know what you're doing. We can start with probing for (PCI) I2C or SMBus adapters. Do you want to probe now? (YES/no): YES Probing for PCI bus adapters... Sorry, no known PCI bus adapters found. We will now try to load each adapter module in turn. If you have undetectable or unsupported adapters, you can have them scanned by manually loading the modules before running this script. To continue, we need module `i2c-dev' to be loaded. Do you want to load `i2c-dev' now? (YES/no): YES Module loaded successfully. We are now going to do the I2C/SMBus adapter probings. Some chips may be double detected; we choose the one with the highest confidence value in that case. If you found that the adapter hung after probing a certain address, you can specify that address to remain unprobed. Next adapter: saa7133[0] (i2c-0) Do you want to scan it? (YES/no/selectively): YES Client found at address 0x4b Handled by driver `tuner' (already loaded), chip type `tda8290+75a' (note: this is probably NOT a sensor chip!) Client found at address 0x50 Probing for `Analog Devices ADM1033'... No Probing for `Analog Devices ADM1034'... No Probing for `SPD EEPROM'... No Probing for `EDID EEPROM'... No Probing for `Maxim MAX6900'... No Some chips are also accessible through the ISA I/O ports. We have to write to arbitrary I/O ports to probe them. This is usually safe though. Yes, you do have ISA I/O ports even if you do not have any ISA slots! Do you want to scan the ISA I/O ports? (YES/no): YES Probing for `National Semiconductor LM78' at 0x290... No Probing for `National Semiconductor LM78-J' at 0x290... No Probing for `National Semiconductor LM79' at 0x290... No Probing for `Winbond W83781D' at 0x290... No Probing for `Winbond W83782D' at 0x290... No Probing for `Silicon Integrated Systems SIS5595'... No Probing for `VIA VT82C686 Integrated Sensors'... No Probing for `VIA VT8231 Integrated Sensors'... No Probing for `IPMI BMC KCS' at 0xca0... No Probing for `IPMI BMC SMIC' at 0xca8... No Some Super I/O chips may also contain sensors. We have to write to standard I/O ports to probe them. This is usually safe. Do you want to scan for Super I/O sensors? (YES/no): YES Probing for Super-I/O at 0x2e/0x2f Trying family `ITE'... Yes Found unknown chip with ID 0x8502 Trying family `National Semiconductor'... No Trying family `SMSC'... Yes Found unknown chip with ID 0x8502 Trying family `VIA/Winbond/Fintek'... No Probing for Super-I/O at 0x4e/0x4f Trying family `ITE'... No Trying family `National Semiconductor'... No Trying family `SMSC'... Yes Found unknown chip with ID 0x0b00 Trying family `VIA/Winbond/Fintek'... No Some CPUs or memory controllers may also contain embedded sensors. Do you want to scan for them? (YES/no): YES AMD K8 thermal sensors... No Intel Core family thermal sensor... No Intel AMB FB-DIMM thermal sensor... No Sorry, no sensors were detected. Either your sensors are not supported, or they are connected to an I2C or SMBus adapter that is not supported. See doc/FAQ, doc/lm_sensors-FAQ.html or http://www.lm-sensors.org/wiki/FAQ (FAQ #4.24.3) for further information. If you find out what chips are on your board, check http://www.lm-sensors.org/wiki/Devices for driver status. Note that I suspect I've got an SMSC 5137 Super-I/O chip, but I can't find information on it. -- Hope this helps, Simon Farnsworth