Man... I looked at that file for hours.... THANKS!!!! ----- Original Message ----- From: "Mark Studebaker" <mds4 at verizon.net> To: "Paul Aviles" <paul.aviles at palei.com> Cc: <sensors at Stimpy.netroedge.com> Sent: Friday, December 24, 2004 10:47 AM Subject: Re: Questions > since your chip is an lm85 you must have a chip section headed with > chip "lm85-*" > > > Paul Aviles wrote: >> Jean, >> >> Happy holidays to you all and best wishes for the new year!! >> >> >> >> Quick question, I have sensors 2.8.8 running on a Tyan GS12 server with >> FC1 and kernel 2.4.22-1.2174.nptl and I got everything working. >> >> >> >> I am curious about a problem. Take a look at my results of sensors. I >> have an alarm on in4 and also shows fan4 which I don't have. My >> sensors.conf is also below and it is supposed to ignore in4 and fan4. Is >> there any other way to eliminate those from being reported? >> >> >> >> Thanks so much. >> >> >> >> Paul >> >> >> #sensors >> >> lm85-i2c-0-2e >> Adapter: SMBus I801 adapter at 1480 >> in0: +2.62 V (min = +0.00 V, max = +3.32 V) >> in1: +1.31 V (min = +0.00 V, max = +2.99 V) >> in2: +3.37 V (min = +0.00 V, max = +4.38 V) >> in3: +5.13 V (min = +0.00 V, max = +6.64 V) >> in4: +0.00 V (min = +0.00 V, max = +15.94 V) ALARM >> fan1: 9294 RPM (min = 0 RPM) >> fan2: 8169 RPM (min = 0 RPM) >> fan3: 9712 RPM (min = 0 RPM) >> fan4: 0 RPM (min = 0 RPM) >> temp1: +61?C (low = -127?C, high = +127?C) >> temp2: +41?C (low = -127?C, high = +127?C) >> temp3: +43?C (low = -127?C, high = +127?C) >> pwm1: 86 >> pwm2: 113 >> pwm3: 88 >> vid: +1.325 V (VRM Version 9.1) >> >> /etc/sensors.conf >> chip "adt7463-*" >> >> ignore pwm1 >> ignore pwm2 >> ignore pwm3 >> ignore in4 >> ignore fan4 >> >> label in0 "+2.6V" >> label in1 "CPU Volt" >> label in2 "+3.3V" >> label in3 "+5V" >> >> label fan1 "fan2" >> label fan2 "fan1" >> label fan3 "fan3" >> >> label pwm1 "pwm1 fan" >> label pwm2 "pwm2 fan" >> label pwm3 "pwm3 fan" >> >> label temp1 "CPU Temp" >> label temp2 "Local Temp" >> label temp3 "System Temp" >> >> set in0_min 2.6 * 0.95 >> set in0_max 2.6 * 1.05 >> set in1_min 1.45 * 0.95 >> set in1_max 1.45 * 1.05 >> set in2_min 3.3 * 0.95 >> set in2_max 3.3 * 1.05 >> set in3_min 5.0 * 0.95 >> set in3_max 5.0 * 1.05 >> >> set vrm 9.1[ >> >> > > > -- > This message has been scanned for viruses and > dangerous content by MailScanner, and is > believed to be clean. > > -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean.
