Intel Desktop Board D875PBZ I have this board, lspci dump: 0000:00:00.0 Host bridge: Intel Corp. 82875P Memory Controller Hub (rev 02) 0000:00:01.0 PCI bridge: Intel Corp. 82875P Processor to AGP Controller (rev 02) 0000:00:03.0 PCI bridge: Intel Corp. 82875P Processor to PCI to CSA Bridge (rev 02) 0000:00:1d.0 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #1 (rev 02) 0000:00:1d.1 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #2 (rev 02) 0000:00:1d.2 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #3 (rev 02) 0000:00:1d.3 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #4 (rev 02) 0000:00:1d.7 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller (rev 02) 0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev c2) 0000:00:1f.0 ISA bridge: Intel Corp. 82801EB/ER (ICH5/ICH5R) LPC Bridge (rev 02) 0000:00:1f.1 IDE interface: Intel Corp. 82801EB/ER (ICH5/ICH5R) Ultra ATA 100 Storage Controller (rev 02) 0000:00:1f.2 IDE interface: Intel Corp. 82801EB (ICH5) Serial ATA 150 Storage Controller (rev 02) 0000:00:1f.3 SMBus: Intel Corp. 82801EB/ER (ICH5/ICH5R) SMBus Controller (rev 02) I couldnt find any info on the lm-sensors website about this hardware. sensors detect said: Bus `SMBus I801 adapter at c800' (Algorithm unavailable) Busdriver `i2c-i801', I2C address 0x2e Chip `SMSC EMC6D100 or EMC6D101' (confidence: 7) and also to be written: ISA bus address 0x06e0 (Busdriver `i2c-isa') Chip `Nat. Semi. PC87372 Super IO Fan Sensors' (confidence 9) and with these modules and the force (as recommended by ruik from IRC) modprobe lm85 force=0,0x2e modprobe i2c_i801 sensors will output: lm85-i2c-0-2e Adapter: SMBus I801 adapter at c800 V1.5: +1.50 V (min = +0.00 V, max = +3.32 V) VCore: +1.32 V (min = +0.00 V, max = +2.99 V) V3.3: +3.30 V (min = +0.00 V, max = +4.38 V) V5: +5.10 V (min = +0.00 V, max = +6.64 V) V12: +12.00 V (min = +0.00 V, max = +15.94 V) CPU_Fan: 2928 RPM (min = 0 RPM) CPU: +44?C (low = -128?C, high = +127?C) Board: +29?C (low = -127?C, high = +127?C) Remote: +29?C (low = -127?C, high = +127?C) CPU_PWM: 255 Fan2_PWM: 255 Fan3_PWM: 255 vid: +1.375 V (VRM Version 9.1) Presumably with the "to be written" bit i should be able to alter the fan PWM ratios and ultimately the fan speed, which would be very nice as i could put to rest a piece of hardware i made which uses the serial port to do PWM! I can't lend hardware but i can help test any new drivers. Thank you -Dave Cunningham
