Do you have a supported I2C bus host? Did you check the syslog for possible errors? Is there anything in /proc/sys/dev/sensors? (That's where the files are which have the raw sensor data.) Phil On Wed, Feb 05, 2003 at 11:20:50PM +0100, Franssens wrote: > I'm sorry, > > in my previous email (just sent it) > I forgot one module. > Here's my new output: > > Module Size Used by > gl518sm 8096 0 (unused) > i2c-proc 6064 0 [gl518sm] > i2c-dev 3712 0 > i2c-philips-par 2256 0 (unused) > parport 24192 0 [i2c-philips-par] > i2c-algo-bit 7712 0 [i2c-philips-par] > i2c-piix4 3824 0 > i2c-isa 1216 0 (unused) > i2c-core 13328 0 [gl518sm i2c-proc i2c-dev i2c-algo-bit > i2c-piix4 i2c-isa] > root at Enterprise:~# sensors -s > No sensors found! > > > greetz, > Anne > > > > > > ----- Original Message ----- > From: <phil at netroedge.com> > To: "Franssens" <dirkleni at rendo.dekooi.nl>; <sensors at Stimpy.netroedge.com> > Sent: Tuesday, February 05, 2002 9:14 PM > Subject: Re: gl518sm > > > > > > I don't see a bus driver listed. In order to communicate with your > > chip (a GL518SM, I presume), you need a i2c bus driver which supports > > your hardware installed. Assuming you have a PIIX4, a good start > > might be to insmod i2c-piix4. Good luck! > > > > > > Phil > > > > On Wed, Feb 05, 2003 at 09:18:15AM +0100, Franssens wrote: > > > I'm having quit some difficulties with lm-sensors. > > > Everything, including installing and compiling worked great, > > > but now it doesn't seem to recognize my gl518sm detectors. > > > when I modprobe that module, > > > and then perform a "sensors -s", it says; no sensors found!. > > > But it really IS listed on your supported hardware page. > > > > > > some help: > > > motherboard: FullYes (82440lx), pentiumII 300HMz, 96MB RAM. > > > > > > lsmod: > > > Module Size Used by > > > gl518sm 8096 0 (unused) > > > i2c-proc 6064 0 [gl518sm] > > > i2c-dev 3712 0 > > > i2c-core 13328 0 [gl518sm i2c-proc i2c-dev] > > > > > > the problem was, that sensordetect did not detect that gl518sm, > > > but a piix4 an an eeprom. > > > The only output sensors would give me then, was some info from eeprom, > > > NOT voltages or fans etc. > > > then I manually tried to modprobe gl518sm, with success. (as you can > see) > > > but unfortunately; > > > sensors -s now says: no sensors found! > > > > > > can you help me? > > > > > > thnx! > > > Anne > > > > -- > > Philip Edelbrock -- IS Manager -- Edge Design, Corvallis, OR > > phil at netroedge.com -- http://www.netroedge.com/~phil > > PGP F16: 01 D2 FD 01 B5 46 F4 F0 3A 8B 9D 7E 14 7F FB 7A > > -- Philip Edelbrock -- IS Manager -- Edge Design, Corvallis, OR phil at netroedge.com -- http://www.netroedge.com/~phil PGP F16: 01 D2 FD 01 B5 46 F4 F0 3A 8B 9D 7E 14 7F FB 7A
