On Thu, 2012-05-10 at 12:13 +0300, Arik Nemtsov wrote: > This series adds initial support for the 18xx chip family. The new > module uses wlcore for functionality common with the 12xx family. > > Arik Nemtsov (28): > wl18xx: create per-chip-family private storage > wl18xx: set the number of Tx descriptors > wl18xx: set normal/GEM Tx spare block counts > wl18xx: implement hw op for calculating hw block count per packet > wl18xx: implement hw op for setting blocks in hw_tx_desc > wl18xx: implement hw op for setting frame length in tx_hw_desc > wl18xx: define HW-rate translation elements/tables > wl18xx: add fw_status private data > wl18xx: set Rx block-size alignment quirk > wl18xx: implement hw op for getting rx buffer data alignment > wl18xx: implement hw op for getting rx packet data length > wl18xx: implement immediate Tx completion > wlcore/wl18xx: add hw op for setting Tx HW checksum > wlcore/wl18xx: add hw op for Rx HW checksum > wlcore: track current channel type per vif > wl18xx: send channel type to FW on role start > wl18xx: ipmlement ap_rate_mask hw op > wlcore: support peer MIMO rates > wlcore/wl18xx: enable MIMO/wide-chan rates in AP-mode rate config > wl18xx: set HT capabilities > wl18xx: add module param for overriding HT caps > wl18xx: read FW pc on recovery > wl18xx: disable FW log functionality > wl18xx: implement hw op to read PG version > wl18xx: init Tx-released index to 0 on HW init > wl18xx: don't upload NVS to FW > wl18xx: change board type enum according to new FW > wlcore/wl12xx/18xx: split fw_status struct into two > > Assaf Azulay (1): > wl18xx: change default tcp_checksum to false > > Luciano Coelho (49): > wl18xx: add new module > wlcore_sdio/wl18xx: use SDIO revision number to identify wl18xx chips > wl18xx: add empty operations struct > wl18xx: add partition table > wl18xx: add register table > wl18xx: add identify chip operation > wl18xx: add some boot operations and hw-specific configurations > wl18xx: add trigger command and ack event operations > wl18xx: add hw_init operation > wl18xx: add runtime configuration parameters > wl18xx: add board type module argument > wl18xx: translate and write the board type to SCR_PAD2 > wl18xx: read clock frequency and do top init accordingly > wlcore: rename wl12xx.h to wlcore_i.h > wlcore/wl12xx: move ref_clock and tcxo_clock elements to wl12xx > wlcore/wl12xx: move rx_mem_pool_addr element to wl12xx > wlcore/wl12xx: add plt_init op and move the code to wl12xx > wl18xx: add plt_init operation > wl18xx: change the low_band_component_type for HDK boards > wl18xx: add number of antennas and dc2dc type as module params > wl18xx: add module parameter to disable TCP checksum > wl18xx: derive the MAC address from the BD_ADDR in fuse ROM > wl18xx: add a module parameter to control 11a support > wlcore: add module parameter to dump SDIO reads and writes > wl18xx: copy the default configuration before checking the board_type > wl18xx: changed default board_type to HDK > wlcore: add space for private area when allocating fw_status > wl18xx: change low_band_component_type value for COM8 > wlcore: reorder identify_chip and get_hw_info > wl18xx: disable MCS_13 for wl18xx PG 1.0 > wlcore: update beacon and probe_resp templates when rates change > wlcore: use all AP basic rates as default > wlcore: abstract debugfs fw_stats to be handled by the lower drivers > wlcore: add debugfs macro to help print fw statistics arrays > wl12xx: implement fw status debugfs entries > wl18xx: implement fw status debugfs entries > wlcore: create private static_data area and add operation to parse it > wl18xx: print the PHY firmware version from the private static data > wlcore: print the interrupt status when recovery is triggered > wl18xx: don't use MIMO when ht_mode is set to wide > wlcore: use proper values for supported local rates > wl18xx: add module parameter to force SISO 20MHz > wl18xx: add power limit reference value to mac_and_phy settings > wl18xx: export low/high band component values as module params > wl18xx: export pwr_limit_reference_11_abg value as a module parameter > wlcore/wl12xx/wl18xx: move lower driver debugfs to a subdir > wlcore: increase aggregation buffer size by one page > wl18xx: increase tx_ba_win_size to 64 > wl18xx: use new fw stats structures Applied and pushed this whole series to wl12xx/master. -- Cheers, Luca. -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
