I can now confirm that the patch below DOES compile, and even works.
Here is the dmesg output on my router:
root@OpenWrt:/tmp# dmesg
b43-phy1: Broadcom 5354 WLAN found (core revision 13)
b43-phy1 debug: Found PHY: Analog 6, Type 5, Revision 0
b43-phy1 debug: Found Radio: Manuf 0x17F, Version 0x2062, Revision 1
phy1: Selected rate control algorithm 'minstrel'
Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ]
b43 ssb0:3: firmware: requesting b43/ucode13.fw
b43 ssb0:3: firmware: requesting b43/lp0initvals13.fw
b43 ssb0:3: firmware: requesting b43/lp0bsinitvals13.fw
b43-phy1: Loading firmware version 410.2160 (2007-05-26 15:32:10)
b43-phy1 debug: b2062: Using crystal tab entry 19200 kHz.
b43-phy1 debug: Chip initialized
b43-phy1 debug: 64-bit DMA initialized
Registered led device: b43-phy1::tx
Registered led device: b43-phy1::rx
b43-phy1 debug: Wireless interface started
b43-phy1 debug: Adding Interface type 2
wlan0: direct probe to AP XXXXXXXX (try 1)
wlan0 direct probe responded
wlan0: authenticate with AP XXXXXXXX (try 1)
wlan0: authenticated
wlan0: associate with AP XXXXXXXX (try 1)
wlan0: RX AssocResp from XXXXXXXX (capab=0x431 status=0 aid=1)
wlan0: associated
b43-phy1 debug: Using hardware based encryption for keyidx: 0, mac: XXXXXXXX
root@OpenWrt:/tmp# iwconfig 2> /dev/null
wlan0 IEEE 802.11bg ESSID:"tommy"
Mode:Managed Frequency:2.412 GHz Access Point: XX:XX:XX:XX:XX:XX
Bit Rate=11 Mb/s Tx-Power=20 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=70/70 Signal level=3 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
On Mo, 2009-09-14 at 21:56 +0200, Thomas Ilnseher wrote:
> On Mo, 2009-09-14 at 21:43 +0200, Gábor Stefanik wrote:
> > Always send patches to John Linville, and CC linux-wireless.
> Ok, the last try ...
>
> As I've seen Gàbor's patch, I noticed that my previous patch was
> bullshit. This patch should work:
>
> (see: http://bcm-v4.sipsolutions.net/802.11/PHY/Anacore)
>
> Signed-off-by: Thomas Ilnseher <illth@xxxxxx>
>
> diff -uNr b/drivers/net/wireless/b43/phy_lp.c
> a/drivers/net/wireless/b43/phy_lp.c
> --- b/drivers/net/wireless/b43/phy_lp.c 2009-09-14 06:14:18.000000000
> +0200
> +++ a/drivers/net/wireless/b43/phy_lp.c 2009-09-14 21:03:15.158507573
> +0200
> @@ -2228,6 +2228,16 @@
> return B43_TXPWR_RES_DONE;
> }
>
> +void b43_lpphy_op_switch_analog(struct b43_wldev *dev, bool on)
> +{
> + if (on) {
> + b43_phy_mask(dev, B43_LPPHY_AFE_CTL_OVR, 0xfff8);
> + } else {
> + b43_phy_set(dev, B43_LPPHY_AFE_CTL_OVRVAL, 0x0007);
> + b43_phy_set(dev, B43_LPPHY_AFE_CTL_OVR, 0x0007);
> + }
> +}
> +
> const struct b43_phy_operations b43_phyops_lp = {
> .allocate = b43_lpphy_op_allocate,
> .free = b43_lpphy_op_free,
> @@ -2239,7 +2249,7 @@
> .radio_read = b43_lpphy_op_radio_read,
> .radio_write = b43_lpphy_op_radio_write,
> .software_rfkill = b43_lpphy_op_software_rfkill,
> - .switch_analog = b43_phyop_switch_analog_generic,
> + .switch_analog = b43_lpphy_op_switch_analog,
> .switch_channel = b43_lpphy_op_switch_channel,
> .get_default_chan = b43_lpphy_op_get_default_chan,
> .set_rx_antenna = b43_lpphy_op_set_rx_antenna,
>
>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
