Search Linux Wireless

Re: [PATCH 1/2] dt-bindings: net: wireless: ath10k: add qcom,no-msa-ready-indicator prop

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





On 3/13/24 16:09, Marc Gonzalez wrote:
[ Dropping the DT fellows ]

On 05/03/2024 20:20, Kalle Valo wrote:

Marc Gonzalez wrote:

I need to build a kernel + rootfs + FW to test the proposed solution,
then I can spin a formal submission.

Yeah, please do test this to make sure we are not missing anything :)

I used buildroot ( https://buildroot.org ) to generate a kernel + rootfs
for my board (a variation of qcom/msm8998-mtp.dts)

Not sure if I must use the vendor FW blobs? Or if I can use the blobs
from linux-firmware-20240115.tar.xz (as supported by BR2).


All I see from the ath10k driver (with debugging cranked to the max) is:

[    0.539801] ath10k_snoc 18800000.wifi: Adding to iommu group 0
[    0.541941] ath10k_snoc 18800000.wifi: snoc xo-cal-data return -22
[    0.543633] ath10k_snoc 18800000.wifi: supply vdd-3.3-ch1 not found, using dummy regulator
[    0.544002] ath10k_snoc 18800000.wifi: qmi msa.paddr: 0x0000000094400000 , msa.vaddr: 0x(____ptrval____)
[    0.544271] ath10k_snoc 18800000.wifi: snoc probe


# ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue qlen 1000
     link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000
     link/ether 34:27:92:82:48:ec brd ff:ff:ff:ff:ff:ff

No wlan device at this point.

I got shell-shock from reading these setup steps:

https://wiki.postmarketos.org/wiki/Qualcomm_Snapdragon_835_(MSM8998)#WLAN
https://github.com/jhugo/linux/blob/5.5rc2_wifi/README


Jeffrey, Bjorn, Konrad,
Has someone written idiot-proof (such as myself) steps to enable
the ath10k core on a msm8998 board?

$ cat /tmp/x.json
[
        {"names": ["bus=snoc,qmi-board-id=stinkyboard"], "data": "board_stink.bin"}
]


$ ls -lh board_stink.bin
-rw-rw-r-- 1 konrad konrad 19K Mar 13 16:42 board_stink.bin


$ python3 ~/qca-swiss-army-knife/tools/scripts/ath10k/ath10k-bdencoder -c /tmp/x.json -o board-2.bin
board binary file 'board-2.bin' is created

I believe Kalle aggregates these boardfiles and then uploads a big
combined board-2.bin to linux-firmware nowadays?

Konrad




[Index of Archives]     [Linux Host AP]     [ATH6KL]     [Linux Wireless Personal Area Network]     [Linux Bluetooth]     [Wireless Regulations]     [Linux Netdev]     [Kernel Newbies]     [Linux Kernel]     [IDE]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite Hiking]     [MIPS Linux]     [ARM Linux]     [Linux RAID]

  Powered by Linux