Search Linux Wireless

Re: [PATCH 1/2] dt-bindings: net: wireless: ath10k: add qcom,no-msa-ready-indicator prop

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, 13 Mar 2024 at 17:09, Marc Gonzalez <mgonzalez@xxxxxxxxxx> wrote:
>
> [ Dropping the DT fellows ]
>
> On 05/03/2024 20:20, Kalle Valo wrote:
>
> > Marc Gonzalez wrote:
> >
> >> I need to build a kernel + rootfs + FW to test the proposed solution,
> >> then I can spin a formal submission.
> >
> > Yeah, please do test this to make sure we are not missing anything :)
>
> I used buildroot ( https://buildroot.org ) to generate a kernel + rootfs
> for my board (a variation of qcom/msm8998-mtp.dts)
>
> Not sure if I must use the vendor FW blobs? Or if I can use the blobs
> from linux-firmware-20240115.tar.xz (as supported by BR2).
>
>
> All I see from the ath10k driver (with debugging cranked to the max) is:
>
> [    0.539801] ath10k_snoc 18800000.wifi: Adding to iommu group 0
> [    0.541941] ath10k_snoc 18800000.wifi: snoc xo-cal-data return -22
> [    0.543633] ath10k_snoc 18800000.wifi: supply vdd-3.3-ch1 not found, using dummy regulator
> [    0.544002] ath10k_snoc 18800000.wifi: qmi msa.paddr: 0x0000000094400000 , msa.vaddr: 0x(____ptrval____)
> [    0.544271] ath10k_snoc 18800000.wifi: snoc probe
>
>
> # ip link
> 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue qlen 1000
>     link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
> 2: enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000
>     link/ether 34:27:92:82:48:ec brd ff:ff:ff:ff:ff:ff
>
> No wlan device at this point.

Do you have pd-mapper, rmtfs and tqftpserv running? You also need to
have wlanmdsp.mbn in the same directory as modem.mbn for your platform
(see how this is handled for sdm845).
If these points are implemented and you still don't have the wlan,
please check for tqftpserv messages in syslog.

>
> I got shell-shock from reading these setup steps:
>
> https://wiki.postmarketos.org/wiki/Qualcomm_Snapdragon_835_(MSM8998)#WLAN
> https://github.com/jhugo/linux/blob/5.5rc2_wifi/README

These readmes are mostly correct. You don't need qrtr now, it is
provided by the kernel.  pd-mapper (protection-domain-mapper),
tqftpserv and rmtfs usually can be installed from your distro.

You can mostly ignore the part for board.bin / board-2.bin for now.
You'll get to that point later, when the driver complains about
missing board data.

Also, if you pick up series at [1], you can put your bdwlan.XXX file
as ath10k/WCN3990/hw1.0/board.bin and skip all the json and stuff.
This will work for the bringup, then you can follow the process at [2]
and submit your file for inclusion into board-2.bin.

[1] https://lore.kernel.org/ath10k/20240130-wcn3990-board-fw-v1-0-738f7c19a8c8@xxxxxxxxxx/
[2] https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles

>
>
> Jeffrey, Bjorn, Konrad,
> Has someone written idiot-proof (such as myself) steps to enable
> the ath10k core on a msm8998 board?
>
> I'm still not quite sure where linux-firmware.git fits into all this.
>
> Regards
>


-- 
With best wishes
Dmitry




[Index of Archives]     [Linux Host AP]     [ATH6KL]     [Linux Wireless Personal Area Network]     [Linux Bluetooth]     [Wireless Regulations]     [Linux Netdev]     [Kernel Newbies]     [Linux Kernel]     [IDE]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite Hiking]     [MIPS Linux]     [ARM Linux]     [Linux RAID]

  Powered by Linux