Am 22.10.2013 20:32, schrieb Yannik Völker: > Am 19.10.2013 18:59, schrieb Oleksij Rempel: >> Am 19.10.2013 14:18, schrieb Yannik Völker: >>> Am 18.10.2013 19:16, schrieb Oleksij Rempel: >>>> Am 18.10.2013 18:33, schrieb Yannik Völker: >>>>> Am 18.10.2013 18:16, schrieb Oleksij Rempel: >>>>>> Am 18.10.2013 17:38, schrieb Yannik Völker: >>>>>>> Am 18.10.2013 17:07, schrieb Oleksij Rempel: >>>>>>>> Am 18.10.2013 16:49, schrieb Alan Stern: >>>>>>>>> Yannik, you should always use Reply-To-All so that >>>>>>>>> your messages get sent to the mailing list and not >>>>>>>>> just to me. >>>>>>>>> >>>>>>>>> On Thu, 17 Oct 2013, Yannik Völker wrote: >>>>>>>>> >>>>>>>>>> Am 07.08.2013 19:34, schrieb Alan Stern: >>>>>>>>>>> Please post two usbmon traces, one showing the >>>>>>>>>>> failure on your current system and the other >>>>>>>>>>> showing the adapter running correctly under a >>>>>>>>>>> 32-bit kernel. Instructions for usbmon are in >>>>>>>>>>> the kernel source file >>>>>>>>>>> Documentation/usb/usbmon.txt. >>>>>>>>>> I never got it to work under a 32-bit kernel, i >>>>>>>>>> was just able to utilize a windows32 driver using >>>>>>>>>> ndiswrapper. >>>>>>>>>> >>>>>>>>>> Now i got it to "work". I randomly found out >>>>>>>>>> that the ar5523 driver actually works when you >>>>>>>>>> load it after you unload ndiswrapper so the >>>>>>>>>> following steps make it work: 1. modprobe >>>>>>>>>> ndiswrapper 2. plug in device 3. connect to wlan >>>>>>>>>> using ndiswrapper and disconnect again (might be >>>>>>>>>> optional) 4. modprobe -r ndiswrapper 5. modprobe >>>>>>>>>> ar5523 6. connect to wlan log for that is >>>>>>>>>> attatched as wlanthennative2.log >>>>>>> >>>>>>> >>>>>>>> It sounds like linux driver didn't recognised usb id >>>>>>>> and didn't uploaded firmware, or there was no >>>>>>>> firmware to upload. >>>>>>> there is firmware (/lib/firmware/ar5523.bin exists) >>>>>>> but it does not even get touched (i renamed the file >>>>>>> and the error did not change at all) >>>>> >>>>>> find first usbid of your adapter (it will be changed >>>>>> after firmware upload). And try to force driver to use >>>>>> this id: modprobe -v ar5523 echo 07d1 3a0d > >>>>>> /sys/bus/usb/drivers/ar5523/new_id >>>>> >>>>>> instead of "07d1 3a0d" use your id. >>>>> >>>>> >>>>> # lsusb … Bus 003 Device 011: ID 129b:160c CyberTAN >>>>> Technology Siemens S30853-S1038-R351 802.11g Wireless >>>>> Adapter [Atheros AR5523] … >>>>> >>>>> # modprobe ar5523 # echo 129b 160c > >>>>> /sys/bus/usb/drivers/ar5523/new_id <plugging device in> >>>>> syslog: Oct 18 18:27:47 yannik-desktop kernel: [ >>>>> 8751.447784] usbcore: registered new interface driver >>>>> ar5523 Oct 18 18:28:25 yannik-desktop kernel: [ >>>>> 8789.036912] usb 3-14: new high-speed USB device number 12 >>>>> using xhci_hcd Oct 18 18:28:25 yannik-desktop kernel: [ >>>>> 8789.053995] usb 3-14: New USB device found, idVendor=129b, >>>>> idProduct=160c Oct 18 18:28:25 yannik-desktop kernel: [ >>>>> 8789.054005] usb 3-14: New USB device strings: Mfr=1, >>>>> Product=2, SerialNumber=3 Oct 18 18:28:25 yannik-desktop >>>>> kernel: [ 8789.054010] usb 3-14: Product: AR5523 Oct 18 >>>>> 18:28:25 yannik-desktop kernel: [ 8789.054015] usb 3-14: >>>>> Manufacturer: Atheros Communications Inc Oct 18 18:28:25 >>>>> yannik-desktop kernel: [ 8789.054019] usb 3-14: >>>>> SerialNumber: 1.0 Oct 18 18:28:27 yannik-desktop kernel: [ >>>>> 8791.052313] usb 3-14: timeout waiting for command 01 reply >>>>> Oct 18 18:28:27 yannik-desktop kernel: [ 8791.052323] usb >>>>> 3-14: could not initialize adapter Oct 18 18:28:27 >>>>> yannik-desktop kernel: [ 8791.052359] usb 3-14: RX USB >>>>> error -2. Oct 18 18:28:27 yannik-desktop kernel: [ >>>>> 8791.052378] usb 3-14: error -1 when submitting rx urb Oct >>>>> 18 18:28:27 yannik-desktop kernel: [ 8791.052504] ar5523: >>>>> probe of 3-14:1.0 failed with error -110 >>>>> >>>>>> Besidy, what kernel version are you using? May be it is >>>>>> too old.. >>>>> >>>>> 3.11.0-12-generic it is my understanding that the ar5523 >>>>> driver was included from 3.8 on. >>> >>>> please test attached patch. >>> Stopped the error from appearing but it looks like it would >>> not even try to upload the firmware to me: > >> Hi Yannik, > >> please use this patch instead of previous. It will provide some >> more info. And send me complete dmesg. > > I have to correct myself: I got the sources via apt-get source (as > opposed to git) this time. applied patch, worked. Thank you for update. Can you please send us dmesg with working result. -- Regards, Oleksij -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
