2013/6/17 Franky Lin <frankyl@xxxxxxxxxxxx>: > On 06/17/2013 09:19 AM, Jason Cooper wrote: >> >> Added Franky... >> >> On Wed, Jun 12, 2013 at 06:21:23PM -0400, Jason Cooper wrote: >>> >>> All, >>> >>> I have a Seagate Wireless Plus I am trying to put a vanilla kernel on >>> (currently v3.10-rc5 for various omap DT bits). >>> >>> I have the board booting and running a debian rootfs on the HD. I just >>> got mmc to come up and I've discovered that the wireless card is vendor >>> 0x02d0, device 0x4319. >>> >>> My hope, once I got to this point, was that I would be able to use >>> the mainline, open source driver. Unfortunately, it looks like brcmfmac >>> lost support for the 0x4319 while it was in staging. >>> >>> The commit in question is: >>> >>> 4dad253 staging: brcm80211: remove code for unsupported chip >>> >>> Is adding it back in a bridge too far? >> >> It looks like only two things are needed, adding the chip id and then >> setting the addresses. Here's a preliminary patch to do just that. >> Note, the addresses I have used are a straight copy from the 4329. It >> causes this: >> >> [ 12.346466] mmcblk mmc0:0001: no of_node; not parsing pinctrl DT >> [ 12.353149] brcmfmac_sdio mmc0:0001:1: no of_node; not parsing pinctrl >> DT >> [ 12.360717] brcmfmac_sdio mmc0:0001:2: no of_node; not parsing pinctrl >> DT >> [ 12.368804] brcmfmac: brcmf_sdio_chip_drivestrengthinit: No SDIO Drive >> strength init done for chip 4319 rev 1 pmurev 7 >> [ 12.380462] brcmfmac: brcmf_sdioh_request_byte: Failed to write byte >> F0:@0x00408=03, Err: -22 >> [ 12.391906] brcmfmac: brcmf_sdioh_request_byte: Failed to write byte >> F0:@0x00408=03, Err: -22 >> [ 12.403289] brcmfmac: brcmf_sdioh_request_byte: Failed to write byte >> F0:@0x00408=03, Err: -22 >> [ 12.412261] brcmfmac: brcmf_sdio_regrw_helper: failed with -22 >> [ 12.418457] brcmfmac: brcmf_sdioh_request_byte: Failed to write byte >> F0:@0x00408=01, Err: -22 >> [ 12.429718] brcmfmac: brcmf_sdioh_request_byte: Failed to write byte >> F0:@0x00408=01, Err: -22 >> [ 12.441101] brcmfmac: brcmf_sdioh_request_byte: Failed to write byte >> F0:@0x00408=01, Err: -22 >> [ 12.450073] brcmfmac: brcmf_sdio_regrw_helper: failed with -22 >> >> I've taken a quick look at aosp, the provided GPL broadcom code, and I >> haven't seen anything for the 4319 wrt to addresses. How hard would it >> be to get those addresses from you guys? > > > Hi Jason, > > The major obstacle of adding 4319 support is the obsolete firmware. Since > it's an EOL chip we are not planning to add the support to brcmfmac. Does it mean, BCM4319 is a "new architecture" chipset, working similarly to the already supported (in brcmfmac) chipsets? When thinking about "old architecture" I mean BCM43236, which AFAIR requires some different driver architecture with some extra memory sharing or sth. -- Rafał -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
