On Tue, Nov 5, 2013 at 9:43 PM, Kamil Debski <k.debski@xxxxxxxxxxx> wrote:
> Add a new driver for the Exynos USB PHY. The new driver uses the generic
> PHY framework. The driver includes support for the Exynos 4x10 and 4x12
> SoC families.
>
> Signed-off-by: Kamil Debski <k.debski@xxxxxxxxxxx>
> Signed-off-by: Kyungmin Park <kyungmin.park@xxxxxxxxxxx>
> ---
> .../devicetree/bindings/phy/samsung-usbphy.txt | 52 ++++
> drivers/phy/Kconfig | 23 +-
> drivers/phy/Makefile | 4 +
> drivers/phy/phy-exynos-usb2.c | 234 ++++++++++++++
> drivers/phy/phy-exynos-usb2.h | 87 ++++++
> drivers/phy/phy-exynos4210-usb2.c | 272 ++++++++++++++++
> drivers/phy/phy-exynos4212-usb2.c | 324 ++++++++++++++++++++
> 7 files changed, 995 insertions(+), 1 deletion(-)
> create mode 100644 Documentation/devicetree/bindings/phy/samsung-usbphy.txt
> create mode 100644 drivers/phy/phy-exynos-usb2.c
> create mode 100644 drivers/phy/phy-exynos-usb2.h
> create mode 100644 drivers/phy/phy-exynos4210-usb2.c
> create mode 100644 drivers/phy/phy-exynos4212-usb2.c
>
> diff --git a/Documentation/devicetree/bindings/phy/samsung-usbphy.txt b/Documentation/devicetree/bindings/phy/samsung-usbphy.txt
> new file mode 100644
> index 0000000..c8fbc70
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/samsung-usbphy.txt
> @@ -0,0 +1,52 @@
> +Samsung S5P/EXYNOS SoC series USB PHY
> +-------------------------------------------------
> +
> +Required properties:
> +- compatible : should be one of the listed compatibles:
> + - "samsung,exynos4210-usbphy"
> + - "samsung,exynos4212-usbphy"
> +- reg : a list of registers used by phy driver
> + - first and obligatory is the location of phy modules registers
> + - second and also required is the location of isolation registers
> + (isolation registers control the physical connection between the in
> + SoC modules and outside of the SoC, this also can be called enable
> + control in the documentation of the SoC)
> + - third is the location of the mode switch register, this only applies
> + to SoCs that have such a feature; mode switching enables to have
> + both host and device used the same SoC pins and is commonly used
> + when OTG is supported
> +- #phy-cells : from the generic phy bindings, must be 1;
> +- clocks and clock-names:
> + - the "phy" clocks is required by the phy module
> + - other clocks are associated by name with their respective phys and
> + are used to determine the value of the clock settings register
> +
> +The second cell in the PHY specifier identifies the PHY, its meaning is
> +compatible dependent. For the currently supported SoCs (Exynos 4210 and
> +Exynos 4212) it is as follows:
> + 0 - USB device,
> + 1 - USB host,
> + 2 - HSIC0,
> + 3 - HSIC1,
> +
> +Example:
> +
> +For Exynos 4412 (compatible with Exynos 4212):
> +
> +exynos_usbphy: exynos-usbphy@125B0000 {
> + compatible = "samsung,exynos4212-usbphy";
> + reg = <0x125B0000 0x100 0x10020704 0x0c 0x1001021c 0x4>;
> + clocks = <&clock 305>, <&clock 2>, <&clock 2>, <&clock 2>,
> + <&clock 2>;
> + clock-names = "phy", "device", "host", "hsic0", "hsic1";
> + status = "okay";
> + #phy-cells = <1>;
> +};
> +
> +Then the PHY can be used in other nodes such as:
> +
> +ehci@12580000 {
> + status = "okay";
> + phys = <&exynos_usbphy 2>;
> + phy-names = "hsic0";
> +};
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index a344f3d..bdf0fab 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -14,7 +14,7 @@ config GENERIC_PHY
> API by which phy drivers can create PHY using the phy framework and
> phy users can obtain reference to the PHY. All the users of this
> framework should select this config.
> -
> +
> config PHY_EXYNOS_MIPI_VIDEO
> tristate "S5P/EXYNOS SoC series MIPI CSI-2/DSI PHY driver"
> help
> @@ -51,4 +51,25 @@ config PHY_EXYNOS_DP_VIDEO
> help
> Support for Display Port PHY found on Samsung EXYNOS SoCs.
>
> +config PHY_EXYNOS_USB2
> + tristate "Samsung USB 2.0 PHY driver"
> + help
> + Enable this to support Samsung USB phy helper driver for Samsung SoCs.
> + This driver provides common interface to interact, for Samsung
> + USB 2.0 PHY driver.
> +
> +config PHY_EXYNOS4210_USB2
> + bool "Support for Exynos 4210"
> + depends on PHY_EXYNOS_USB2
> + depends on CPU_EXYNOS4210
> + help
> + Enable USB PHY support for Exynos 4210
> +
> +config PHY_EXYNOS4212_USB2
> + bool "Support for Exynos 4212"
> + depends on PHY_EXYNOS_USB2
> + depends on (SOC_EXYNOS4212 || SOC_EXYNOS4412)
> + help
> + Enable USB PHY support for Exynos 4212
> +
> endmenu
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index d0caae9..c87bc65 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -7,3 +7,7 @@ obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO) += phy-exynos-dp-video.o
> obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO) += phy-exynos-mipi-video.o
> obj-$(CONFIG_OMAP_USB2) += phy-omap-usb2.o
> obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o
> +obj-$(CONFIG_PHY_EXYNOS5250_USB) += phy-exynos5250-usb.o
> +obj-$(CONFIG_PHY_EXYNOS_USB2) += phy-exynos-usb2.o
> +obj-$(CONFIG_PHY_EXYNOS4210_USB2) += phy-exynos4210-usb2.o
> +obj-$(CONFIG_PHY_EXYNOS4212_USB2) += phy-exynos4212-usb2.o
> diff --git a/drivers/phy/phy-exynos-usb2.c b/drivers/phy/phy-exynos-usb2.c
> new file mode 100644
> index 0000000..3e9d525
> --- /dev/null
> +++ b/drivers/phy/phy-exynos-usb2.c
> @@ -0,0 +1,234 @@
> +/*
> + * Samsung S5P/EXYNOS SoC series USB PHY driver
> + *
> + * Copyright (C) 2013 Samsung Electronics Co., Ltd.
> + * Author: Kamil Debski <k.debski@xxxxxxxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/spinlock.h>
> +#include "phy-exynos-usb2.h"
> +
> +static int exynos_usb2_phy_power_on(struct phy *phy)
> +{
> + struct usb2_phy_instance *inst = phy_get_drvdata(phy);
> + struct usb2_phy_driver *drv = inst->drv;
> + int ret;
> +
> + dev_dbg(drv->dev, "Request to power_on \"%s\" usb phy\n",
> + inst->cfg->label);
> + ret = clk_prepare_enable(drv->clk);
> + if (ret)
> + return ret;
> + if (inst->cfg->power_on) {
> + spin_lock(&drv->lock);
> + ret = inst->cfg->power_on(inst);
> + spin_unlock(&drv->lock);
> + }
> + clk_disable_unprepare(drv->clk);
> + return ret;
> +}
> +
> +static int exynos_usb2_phy_power_off(struct phy *phy)
> +{
> + struct usb2_phy_instance *inst = phy_get_drvdata(phy);
> + struct usb2_phy_driver *drv = inst->drv;
> + int ret;
> +
> + dev_dbg(drv->dev, "Request to power_off \"%s\" usb phy\n",
> + inst->cfg->label);
> + ret = clk_prepare_enable(drv->clk);
> + if (ret)
> + return ret;
> + if (inst->cfg->power_off) {
> + spin_lock(&drv->lock);
> + ret = inst->cfg->power_off(inst);
> + spin_unlock(&drv->lock);
> + }
> + clk_disable_unprepare(drv->clk);
> + return ret;
> +}
> +
> +static struct phy_ops exynos_usb2_phy_ops = {
> + .power_on = exynos_usb2_phy_power_on,
> + .power_off = exynos_usb2_phy_power_off,
> + .owner = THIS_MODULE,
> +};
> +
> +static struct phy *exynos_usb2_phy_xlate(struct device *dev,
> + struct of_phandle_args *args)
> +{
> + struct usb2_phy_driver *drv;
> +
> + drv = dev_get_drvdata(dev);
> + if (!drv)
> + return ERR_PTR(-EINVAL);
> +
> + if (WARN_ON(args->args[0] >= drv->cfg->num_phys))
> + return ERR_PTR(-ENODEV);
> +
> + return drv->usb2_phy_instances[args->args[0]].phy;
> +}
> +
> +static const struct of_device_id exynos_usb2_phy_of_match[];
> +
> +static int exynos_usb2_phy_probe(struct platform_device *pdev)
> +{
> + struct usb2_phy_driver *drv;
> + struct device *dev = &pdev->dev;
> + struct resource *mem;
> + struct phy_provider *phy_provider;
> +
> + const struct of_device_id *match;
> + const struct usb2_phy_config *cfg;
> + struct clk *clk;
> +
> + int i;
> +
> + match = of_match_node(exynos_usb2_phy_of_match, pdev->dev.of_node);
> + if (!match) {
> + dev_err(dev, "of_match_node() failed\n");
> + return -EINVAL;
> + }
> + cfg = match->data;
> + if (!cfg) {
> + dev_err(dev, "Failed to get configuration\n");
> + return -EINVAL;
> + }
> +
> + drv = devm_kzalloc(dev, sizeof(struct usb2_phy_driver) +
> + cfg->num_phys * sizeof(struct usb2_phy_instance), GFP_KERNEL);
> +
> + if (!drv) {
> + dev_err(dev, "Failed to allocate memory\n");
> + return -ENOMEM;
> + }
> +
> + dev_set_drvdata(dev, drv);
> + spin_lock_init(&drv->lock);
> +
> + drv->cfg = cfg;
> + drv->dev = dev;
> +
> + mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + drv->reg_phy = devm_ioremap_resource(dev, mem);
> + if (IS_ERR(drv->reg_phy)) {
> + dev_err(dev, "Failed to map register memory (phy)\n");
> + return PTR_ERR(drv->reg_phy);
> + }
> +
> + mem = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> + drv->reg_isol = devm_ioremap_resource(dev, mem);
> + if (IS_ERR(drv->reg_isol)) {
> + dev_err(dev, "Failed to map register memory (isolation)\n");
> + return PTR_ERR(drv->reg_isol);
> + }
> +
> + if (drv->cfg->has_mode_switch) {
> + mem = platform_get_resource(pdev, IORESOURCE_MEM, 2);
> + drv->reg_mode = devm_ioremap_resource(dev, mem);
> + if (IS_ERR(drv->reg_mode)) {
> + dev_err(dev, "Failed to map register memory (mode switch)\n");
> + return PTR_ERR(drv->reg_mode);
> + }
> + }
> +
> + phy_provider = devm_of_phy_provider_register(dev,
> + exynos_usb2_phy_xlate);
> + if (IS_ERR(phy_provider)) {
> + dev_err(drv->dev, "Failed to register phy provider\n");
> + return PTR_ERR(phy_provider);
> + }
> +
> + drv->clk = devm_clk_get(dev, "phy");
> + if (IS_ERR(drv->clk)) {
> + dev_err(dev, "Failed to get clock of phy controller\n");
> + return PTR_ERR(drv->clk);
> + }
> +
> + for (i = 0; i < drv->cfg->num_phys; i++) {
> + char *label = drv->cfg->phys[i].label;
> + struct usb2_phy_instance *p = &drv->usb2_phy_instances[i];
> +
> + dev_dbg(dev, "Creating phy \"%s\"\n", label);
> + p->phy = devm_phy_create(dev, &exynos_usb2_phy_ops, NULL);
> + if (IS_ERR(p->phy)) {
> + dev_err(drv->dev, "Failed to create usb2_phy \"%s\"\n",
> + label);
> + return PTR_ERR(p->phy);
> + }
> +
> + p->cfg = &drv->cfg->phys[i];
> + p->drv = drv;
> + phy_set_drvdata(p->phy, p);
> +
> + clk = clk_get(dev, p->cfg->label);
> + if (IS_ERR(clk)) {
> + dev_err(dev, "Failed to get clock of \"%s\" phy\n",
> + p->cfg->label);
> + return PTR_ERR(clk);
> + }
> +
> + p->rate = clk_get_rate(clk);
> +
> + if (p->cfg->rate_to_clk) {
> + p->clk = p->cfg->rate_to_clk(p->rate);
> + if (p->clk == CLKSEL_ERROR) {
> + dev_err(dev, "Clock rate (%ld) not supported\n",
> + p->rate);
> + clk_put(clk);
> + return -EINVAL;
> + }
> + }
> + clk_put(clk);
> + }
> +
> + return 0;
> +}
> +
> +extern const struct usb2_phy_config exynos4210_usb2_phy_config;
> +extern const struct usb2_phy_config exynos4212_usb2_phy_config;
> +
> +static const struct of_device_id exynos_usb2_phy_of_match[] = {
> +#ifdef CONFIG_PHY_EXYNOS4210_USB2
> + {
> + .compatible = "samsung,exynos4210-usb2-phy",
> + .data = &exynos4210_usb2_phy_config,
> + },
> +#endif
> +#ifdef CONFIG_PHY_EXYNOS4212_USB2
> + {
> + .compatible = "samsung,exynos4212-usb2-phy",
> + .data = &exynos4212_usb2_phy_config,
> + },
> +#endif
> + { },
> +};
> +
> +static struct platform_driver exynos_usb2_phy_driver = {
> + .probe = exynos_usb2_phy_probe,
> + .driver = {
> + .of_match_table = exynos_usb2_phy_of_match,
> + .name = "exynos-usb2-phy",
> + .owner = THIS_MODULE,
> + }
> +};
> +
> +module_platform_driver(exynos_usb2_phy_driver);
> +MODULE_DESCRIPTION("Samsung S5P/EXYNOS SoC USB PHY driver");
> +MODULE_AUTHOR("Kamil Debski <k.debski@xxxxxxxxxxx>");
> +MODULE_LICENSE("GPL v2");
> +MODULE_ALIAS("platform:exynos-usb2-phy");
> +
> diff --git a/drivers/phy/phy-exynos-usb2.h b/drivers/phy/phy-exynos-usb2.h
> new file mode 100644
> index 0000000..91e4f73
> --- /dev/null
> +++ b/drivers/phy/phy-exynos-usb2.h
> @@ -0,0 +1,87 @@
> +/*
> + * Samsung S5P/EXYNOS SoC series USB PHY driver
> + *
> + * Copyright (C) 2013 Samsung Electronics Co., Ltd.
> + * Author: Kamil Debski <k.debski@xxxxxxxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#ifndef _PHY_EXYNOS_USB2_H
> +#define _PHY_EXYNOS_USB2_H
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/spinlock.h>
> +
> +#define CLKSEL_ERROR -1
> +
> +#ifndef KHZ
> +#define KHZ 1000
> +#endif
> +
> +#ifndef MHZ
> +#define MHZ (KHZ * KHZ)
> +#endif
> +
> +enum phy_type {
> + PHY_DEVICE,
> + PHY_HOST,
> +};
> +
> +enum usb2_phy_state {
> + STATE_OFF,
> + STATE_ON,
> +};
> +
> +struct usb2_phy_driver;
> +struct usb2_phy_instance;
> +struct usb2_phy_config;
> +
> +struct usb2_phy_instance {
> + struct usb2_phy_driver *drv;
> + struct phy *phy;
> + const struct common_phy *cfg;
> + enum usb2_phy_state state;
> + u32 clk;
> + unsigned long rate;
> +};
> +
> +struct usb2_phy_driver {
> + struct device *dev;
> + spinlock_t lock;
> + void __iomem *reg_phy;
> + void __iomem *reg_isol;
> + void __iomem *reg_mode;
> + const struct usb2_phy_config *cfg;
> + struct clk *clk;
> + struct usb2_phy_instance usb2_phy_instances[0];
> +};
> +
> +struct common_phy {
> + char *label;
> + enum phy_type type;
> + unsigned int id;
> + u32 (*rate_to_clk)(unsigned long);
> + int (*power_on)(struct usb2_phy_instance*);
> + int (*power_off)(struct usb2_phy_instance*);
> +};
> +
> +
> +struct usb2_phy_config {
> + int num_phys;
> + const struct common_phy *phys;
> + char has_mode_switch;
> +};
> +
> +#endif
> +
> diff --git a/drivers/phy/phy-exynos4210-usb2.c b/drivers/phy/phy-exynos4210-usb2.c
> new file mode 100644
> index 0000000..d04ee8e
> --- /dev/null
> +++ b/drivers/phy/phy-exynos4210-usb2.c
> @@ -0,0 +1,272 @@
> +/*
> + * Samsung S5P/EXYNOS SoC series USB PHY driver
> + *
> + * Copyright (C) 2013 Samsung Electronics Co., Ltd.
> + * Author: Kamil Debski <k.debski@xxxxxxxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/spinlock.h>
> +#include "phy-exynos-usb2.h"
> +
> +/* Exynos USB PHY registers */
> +
> +/* PHY power control */
> +#define EXYNOS_4210_UPHYPWR 0x0
> +
> +#define EXYNOS_4210_UPHYPWR_PHY0_SUSPEND (1 << 0)
> +#define EXYNOS_4210_UPHYPWR_PHY0_PWR (1 << 3)
> +#define EXYNOS_4210_UPHYPWR_PHY0_OTG_PWR (1 << 4)
> +#define EXYNOS_4210_UPHYPWR_PHY0_SLEEP (1 << 5)
> +#define EXYNOS_4210_UPHYPWR_PHY0 ( \
> + EXYNOS_4210_UPHYPWR_PHY0_SUSPEND | \
> + EXYNOS_4210_UPHYPWR_PHY0_PWR | \
> + EXYNOS_4210_UPHYPWR_PHY0_OTG_PWR | \
> + EXYNOS_4210_UPHYPWR_PHY0_SLEEP)
> +
> +#define EXYNOS_4210_UPHYPWR_PHY1_SUSPEND (1 << 6)
> +#define EXYNOS_4210_UPHYPWR_PHY1_PWR (1 << 7)
> +#define EXYNOS_4210_UPHYPWR_PHY1_SLEEP (1 << 8)
> +#define EXYNOS_4210_UPHYPWR_PHY1 ( \
> + EXYNOS_4210_UPHYPWR_PHY1_SUSPEND | \
> + EXYNOS_4210_UPHYPWR_PHY1_PWR | \
> + EXYNOS_4210_UPHYPWR_PHY1_SLEEP)
> +
> +#define EXYNOS_4210_UPHYPWR_HSCI0_SUSPEND (1 << 9)
> +#define EXYNOS_4210_UPHYPWR_HSCI0_SLEEP (1 << 10)
> +#define EXYNOS_4210_UPHYPWR_HSCI0 ( \
> + EXYNOS_4210_UPHYPWR_HSCI0_SUSPEND | \
> + EXYNOS_4210_UPHYPWR_HSCI0_SLEEP)
> +
> +#define EXYNOS_4210_UPHYPWR_HSCI1_SUSPEND (1 << 11)
> +#define EXYNOS_4210_UPHYPWR_HSCI1_SLEEP (1 << 12)
> +#define EXYNOS_4210_UPHYPWR_HSCI1 ( \
> + EXYNOS_4210_UPHYPWR_HSCI1_SUSPEND | \
> + EXYNOS_4210_UPHYPWR_HSCI1_SLEEP)
> +
> +/* PHY clock control */
> +#define EXYNOS_4210_UPHYCLK 0x4
> +
> +#define EXYNOS_4210_UPHYCLK_PHYFSEL_MASK (0x3 << 0)
> +#define EXYNOS_4210_UPHYCLK_PHYFSEL_48MHZ (0x0 << 0)
> +#define EXYNOS_4210_UPHYCLK_PHYFSEL_24MHZ (0x3 << 0)
> +#define EXYNOS_4210_UPHYCLK_PHYFSEL_12MHZ (0x2 << 0)
> +
> +#define EXYNOS_4210_UPHYCLK_PHY0_ID_PULLUP (0x1 << 2)
> +#define EXYNOS_4210_UPHYCLK_PHY0_COMMON_ON (0x1 << 4)
> +#define EXYNOS_4210_UPHYCLK_PHY1_COMMON_ON (0x1 << 7)
> +
> +/* PHY reset control */
> +#define EXYNOS_4210_UPHYRST 0x8
> +
> +#define EXYNOS_4210_URSTCON_PHY0 (1 << 0)
> +#define EXYNOS_4210_URSTCON_OTG_HLINK (1 << 1)
> +#define EXYNOS_4210_URSTCON_OTG_PHYLINK (1 << 2)
> +#define EXYNOS_4210_URSTCON_PHY1_ALL (1 << 3)
> +#define EXYNOS_4210_URSTCON_PHY1_P0 (1 << 4)
> +#define EXYNOS_4210_URSTCON_PHY1_P1P2 (1 << 5)
> +#define EXYNOS_4210_URSTCON_HOST_LINK_ALL (1 << 6)
> +#define EXYNOS_4210_URSTCON_HOST_LINK_P0 (1 << 7)
> +#define EXYNOS_4210_URSTCON_HOST_LINK_P1 (1 << 8)
> +#define EXYNOS_4210_URSTCON_HOST_LINK_P2 (1 << 9)
> +
> +/* Isolation, configured in the power management unit */
> +#define EXYNOS_4210_USB_ISOL_DEVICE_OFFSET 0x0
> +#define EXYNOS_4210_USB_ISOL_DEVICE (1 << 0)
> +#define EXYNOS_4210_USB_ISOL_HOST_OFFSET 0x4
> +#define EXYNOS_4210_USB_ISOL_HOST (1 << 0)
> +
> +/* USBYPHY1 Floating prevention */
> +#define EXYNOS_4210_UPHY1CON 0x34
> +#define EXYNOS_4210_UPHY1CON_FLOAT_PREVENTION 0x1
> +
> +enum exynos4210_phy_id {
> + EXYNOS4210_DEVICE,
> + EXYNOS4210_HOST,
> + EXYNOS4210_HSIC0,
> + EXYNOS4210_HSIC1,
> + EXYNOS4210_NUM_PHYS,
> +};
> +
> +/*
> + * exynos4210_rate_to_clk() converts the supplied clock rate to the value that
> + * can be written to the phy register.
> + */
> +static u32 exynos4210_rate_to_clk(unsigned long rate)
> +{
> + unsigned int clksel;
> +
> + switch (rate) {
> + case 12 * MHZ:
> + clksel = EXYNOS_4210_UPHYCLK_PHYFSEL_12MHZ;
> + break;
> + case 24 * MHZ:
> + clksel = EXYNOS_4210_UPHYCLK_PHYFSEL_24MHZ;
> + break;
> + case 48 * MHZ:
> + clksel = EXYNOS_4210_UPHYCLK_PHYFSEL_48MHZ;
> + break;
> + default:
> + clksel = CLKSEL_ERROR;
> + }
> +
> + return clksel;
> +}
> +
> +static void exynos4210_isol(struct usb2_phy_instance *inst, bool on)
Can we have this functionality as xxxx_pwr_on and plugged into generic phy ops?
> +{
> + struct usb2_phy_driver *drv = inst->drv;
> + u32 offset;
> + u32 mask;
> + u32 tmp;
> +
> + if (!drv->reg_isol)
> + return;
> +
> + switch (inst->cfg->id) {
> + case EXYNOS4210_DEVICE:
> + offset = EXYNOS_4210_USB_ISOL_DEVICE_OFFSET;
> + mask = EXYNOS_4210_USB_ISOL_DEVICE;
> + break;
> + case EXYNOS4210_HOST:
> + offset = EXYNOS_4210_USB_ISOL_HOST_OFFSET;
> + mask = EXYNOS_4210_USB_ISOL_HOST;
> + break;
> + default:
> + return;
> + };
> +
> + tmp = readl(drv->reg_isol + offset);
> + if (on)
> + tmp &= ~mask;
> + else
> + tmp |= mask;
> + writel(tmp, drv->reg_isol + offset);
> +}
> +
> +static void exynos4210_phy_pwr(struct usb2_phy_instance *inst, bool on)
It would be better to rename this as xxxx_phy_init and plugged into
phy_ops .init routine.
With this, we can use phy_ops->init in ehci-exynos driver to do the
init and power_on which
would be more aligned with the generic PHY framework.
@Kishon: Please correct me if i am wrong.
> +{
> + struct usb2_phy_driver *drv = inst->drv;
> + u32 rstbits = 0;
> + u32 phypwr = 0;
> + u32 rst;
> + u32 pwr;
> +
> + switch (inst->cfg->id) {
> + case EXYNOS4210_DEVICE:
> + phypwr = EXYNOS_4210_UPHYPWR_PHY0;
> + rstbits = EXYNOS_4210_URSTCON_PHY0;
> + break;
> + case EXYNOS4210_HOST:
> + phypwr = EXYNOS_4210_UPHYPWR_PHY1;
> + rstbits = EXYNOS_4210_URSTCON_PHY1_ALL |
> + EXYNOS_4210_URSTCON_PHY1_P0 |
> + EXYNOS_4210_URSTCON_PHY1_P1P2 |
> + EXYNOS_4210_URSTCON_HOST_LINK_ALL |
> + EXYNOS_4210_URSTCON_HOST_LINK_P0;
> + writel(on, drv->reg_phy + EXYNOS_4210_UPHY1CON);
> + break;
> + case EXYNOS4210_HSIC0:
> + phypwr = EXYNOS_4210_UPHYPWR_HSCI0;
> + rstbits = EXYNOS_4210_URSTCON_PHY1_P1P2 |
> + EXYNOS_4210_URSTCON_HOST_LINK_P1;
> + break;
> + case EXYNOS4210_HSIC1:
> + phypwr = EXYNOS_4210_UPHYPWR_HSCI1;
> + rstbits = EXYNOS_4210_URSTCON_PHY1_P1P2 |
> + EXYNOS_4210_URSTCON_HOST_LINK_P2;
> + break;
> + };
> +
> + if (on) {
> + writel(inst->clk, drv->reg_phy + EXYNOS_4210_UPHYCLK);
> +
> + pwr = readl(drv->reg_phy + EXYNOS_4210_UPHYPWR);
> + pwr &= ~phypwr;
> + writel(pwr, drv->reg_phy + EXYNOS_4210_UPHYPWR);
> +
> + rst = readl(drv->reg_phy + EXYNOS_4210_UPHYRST);
> + rst |= rstbits;
> + writel(rst, drv->reg_phy + EXYNOS_4210_UPHYRST);
> + udelay(10);
> + rst &= ~rstbits;
> + writel(rst, drv->reg_phy + EXYNOS_4210_UPHYRST);
> + } else {
> + pwr = readl(drv->reg_phy + EXYNOS_4210_UPHYPWR);
> + pwr |= phypwr;
> + writel(pwr, drv->reg_phy + EXYNOS_4210_UPHYPWR);
> + }
> +}
> +
> +static int exynos4210_power_on(struct usb2_phy_instance *inst)
> +{
> + /* Order of initialisation is important - first power then isolation */
> + exynos4210_phy_pwr(inst, 1);
> + exynos4210_isol(inst, 0);
> +
> + return 0;
> +}
> +
> +static int exynos4210_power_off(struct usb2_phy_instance *inst)
> +{
> + exynos4210_isol(inst, 1);
> + exynos4210_phy_pwr(inst, 0);
> +
> + return 0;
> +}
> +
> +
> +static const struct common_phy exynos4210_phys[] = {
> + {
> + .label = "device",
> + .type = PHY_DEVICE,
> + .id = EXYNOS4210_DEVICE,
> + .rate_to_clk = exynos4210_rate_to_clk,
> + .power_on = exynos4210_power_on,
> + .power_off = exynos4210_power_off,
> + },
> + {
> + .label = "host",
> + .type = PHY_HOST,
> + .id = EXYNOS4210_HOST,
> + .rate_to_clk = exynos4210_rate_to_clk,
> + .power_on = exynos4210_power_on,
> + .power_off = exynos4210_power_off,
> + },
> + {
> + .label = "hsic0",
> + .type = PHY_HOST,
> + .id = EXYNOS4210_HSIC0,
> + .rate_to_clk = exynos4210_rate_to_clk,
> + .power_on = exynos4210_power_on,
> + .power_off = exynos4210_power_off,
> + },
> + {
> + .label = "hsic1",
> + .type = PHY_HOST,
> + .id = EXYNOS4210_HSIC1,
> + .rate_to_clk = exynos4210_rate_to_clk,
> + .power_on = exynos4210_power_on,
> + .power_off = exynos4210_power_off,
> + },
> + {},
> +};
> +
> +const struct usb2_phy_config exynos4210_usb2_phy_config = {
> + .num_phys = EXYNOS4210_NUM_PHYS,
> + .phys = exynos4210_phys,
> + .has_mode_switch = 1,
> +};
> +
> diff --git a/drivers/phy/phy-exynos4212-usb2.c b/drivers/phy/phy-exynos4212-usb2.c
> new file mode 100644
> index 0000000..654efe0
> --- /dev/null
> +++ b/drivers/phy/phy-exynos4212-usb2.c
> @@ -0,0 +1,324 @@
> +/*
> + * Samsung S5P/EXYNOS SoC series USB PHY driver
> + *
> + * Copyright (C) 2013 Samsung Electronics Co., Ltd.
> + * Author: Kamil Debski <k.debski@xxxxxxxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/spinlock.h>
> +#include "phy-exynos-usb2.h"
> +
> +/* Exynos USB PHY registers */
> +
> +/* PHY power control */
> +#define EXYNOS_4212_UPHYPWR 0x0
> +
> +#define EXYNOS_4212_UPHYPWR_DEV_SUSPEND (1 << 0)
> +#define EXYNOS_4212_UPHYPWR_DEV_PWR (1 << 3)
> +#define EXYNOS_4212_UPHYPWR_DEV_OTG_PWR (1 << 4)
> +#define EXYNOS_4212_UPHYPWR_DEV_SLEEP (1 << 5)
> +#define EXYNOS_4212_UPHYPWR_DEV ( \
> + EXYNOS_4212_UPHYPWR_DEV_SUSPEND | \
> + EXYNOS_4212_UPHYPWR_DEV_PWR | \
> + EXYNOS_4212_UPHYPWR_DEV_OTG_PWR | \
> + EXYNOS_4212_UPHYPWR_DEV_SLEEP)
> +
> +#define EXYNOS_4212_UPHYPWR_HOST_SUSPEND (1 << 6)
> +#define EXYNOS_4212_UPHYPWR_HOST_PWR (1 << 7)
> +#define EXYNOS_4212_UPHYPWR_HOST_SLEEP (1 << 8)
> +#define EXYNOS_4212_UPHYPWR_HOST ( \
> + EXYNOS_4212_UPHYPWR_HOST_SUSPEND | \
> + EXYNOS_4212_UPHYPWR_HOST_PWR | \
> + EXYNOS_4212_UPHYPWR_HOST_SLEEP)
> +
> +#define EXYNOS_4212_UPHYPWR_HSCI0_SUSPEND (1 << 9)
> +#define EXYNOS_4212_UPHYPWR_HSCI0_PWR (1 << 10)
> +#define EXYNOS_4212_UPHYPWR_HSCI0_SLEEP (1 << 11)
> +#define EXYNOS_4212_UPHYPWR_HSCI0 ( \
> + EXYNOS_4212_UPHYPWR_HSCI0_SUSPEND | \
> + EXYNOS_4212_UPHYPWR_HSCI0_PWR | \
> + EXYNOS_4212_UPHYPWR_HSCI0_SLEEP)
> +
> +#define EXYNOS_4212_UPHYPWR_HSCI1_SUSPEND (1 << 12)
> +#define EXYNOS_4212_UPHYPWR_HSCI1_PWR (1 << 13)
> +#define EXYNOS_4212_UPHYPWR_HSCI1_SLEEP (1 << 14)
> +#define EXYNOS_4212_UPHYPWR_HSCI1 ( \
> + EXYNOS_4212_UPHYPWR_HSCI1_SUSPEND | \
> + EXYNOS_4212_UPHYPWR_HSCI1_PWR | \
> + EXYNOS_4212_UPHYPWR_HSCI1_SLEEP)
> +
> +/* PHY clock control */
> +#define EXYNOS_4212_UPHYCLK 0x4
> +
> +#define EXYNOS_4212_UPHYCLK_PHYFSEL_MASK (0x7 << 0)
> +#define EXYNOS_4212_UPHYCLK_PHYFSEL_9MHZ6 (0x0 << 0)
> +#define EXYNOS_4212_UPHYCLK_PHYFSEL_10MHZ (0x1 << 0)
> +#define EXYNOS_4212_UPHYCLK_PHYFSEL_12MHZ (0x2 << 0)
> +#define EXYNOS_4212_UPHYCLK_PHYFSEL_19MHZ2 (0x3 << 0)
> +#define EXYNOS_4212_UPHYCLK_PHYFSEL_20MHZ (0x4 << 0)
> +#define EXYNOS_4212_UPHYCLK_PHYFSEL_24MHZ (0x5 << 0)
> +#define EXYNOS_4212_UPHYCLK_PHYFSEL_50MHZ (0x7 << 0)
> +
> +#define EXYNOS_4212_UPHYCLK_PHY0_ID_PULLUP (0x1 << 3)
> +#define EXYNOS_4212_UPHYCLK_PHY0_COMMON_ON (0x1 << 4)
> +#define EXYNOS_4212_UPHYCLK_PHY1_COMMON_ON (0x1 << 7)
> +
> +#define EXYNOS_4212_UPHYCLK_HSIC_REFCLK_MASK (0x7f << 10)
> +#define EXYNOS_4212_UPHYCLK_HSIC_REFCLK_12MHZ (0x24 << 10)
> +#define EXYNOS_4212_UPHYCLK_HSIC_REFCLK_15MHZ (0x1c << 10)
> +#define EXYNOS_4212_UPHYCLK_HSIC_REFCLK_16MHZ (0x1a << 10)
> +#define EXYNOS_4212_UPHYCLK_HSIC_REFCLK_19MHZ2 (0x15 << 10)
> +#define EXYNOS_4212_UPHYCLK_HSIC_REFCLK_20MHZ (0x14 << 10)
> +
> +/* PHY reset control */
> +#define EXYNOS_4212_UPHYRST 0x8
> +
> +#define EXYNOS_4212_URSTCON_DEVICE (1 << 0)
> +#define EXYNOS_4212_URSTCON_OTG_HLINK (1 << 1)
> +#define EXYNOS_4212_URSTCON_OTG_PHYLINK (1 << 2)
> +#define EXYNOS_4212_URSTCON_HOST_PHY (1 << 3)
> +#define EXYNOS_4212_URSTCON_PHY1 (1 << 4)
> +#define EXYNOS_4212_URSTCON_HSIC0 (1 << 5)
> +#define EXYNOS_4212_URSTCON_HSIC1 (1 << 6)
> +#define EXYNOS_4212_URSTCON_HOST_LINK_ALL (1 << 7)
> +#define EXYNOS_4212_URSTCON_HOST_LINK_P0 (1 << 8)
> +#define EXYNOS_4212_URSTCON_HOST_LINK_P1 (1 << 9)
> +#define EXYNOS_4212_URSTCON_HOST_LINK_P2 (1 << 10)
> +
> +/* Isolation, configured in the power management unit */
> +#define EXYNOS_4212_USB_ISOL_OFFSET 0x0
> +#define EXYNOS_4212_USB_ISOL_OTG (1 << 0)
> +#define EXYNOS_4212_USB_ISOL_HSIC0_OFFSET 0x4
> +#define EXYNOS_4212_USB_ISOL_HSIC0 (1 << 0)
> +#define EXYNOS_4212_USB_ISOL_HSIC1_OFFSET 0x8
> +#define EXYNOS_4212_USB_ISOL_HSIC1 (1 << 0)
> +
> +enum exynos4x12_phy_id {
> + EXYNOS4212_DEVICE,
> + EXYNOS4212_HOST,
> + EXYNOS4212_HSIC0,
> + EXYNOS4212_HSIC1,
> + EXYNOS4212_NUM_PHYS,
> +};
> +
> +/*
> + * exynos4212_rate_to_clk() converts the supplied clock rate to the value that
> + * can be written to the phy register.
> + */
> +static u32 exynos4212_rate_to_clk(unsigned long rate)
> +{
> + unsigned int clksel;
> +
> + /* EXYNOS_4212_UPHYCLK_PHYFSEL_MASK */
> +
> + switch (rate) {
> + case 9600 * KHZ:
> + clksel = EXYNOS_4212_UPHYCLK_PHYFSEL_9MHZ6;
> + break;
> + case 10 * MHZ:
> + clksel = EXYNOS_4212_UPHYCLK_PHYFSEL_10MHZ;
> + break;
> + case 12 * MHZ:
> + clksel = EXYNOS_4212_UPHYCLK_PHYFSEL_12MHZ;
> + break;
> + case 19200 * KHZ:
> + clksel = EXYNOS_4212_UPHYCLK_PHYFSEL_19MHZ2;
> + break;
> + case 20 * MHZ:
> + clksel = EXYNOS_4212_UPHYCLK_PHYFSEL_20MHZ;
> + break;
> + case 24 * MHZ:
> + clksel = EXYNOS_4212_UPHYCLK_PHYFSEL_24MHZ;
> + break;
> + case 50 * MHZ:
> + clksel = EXYNOS_4212_UPHYCLK_PHYFSEL_50MHZ;
> + break;
> + default:
> + clksel = CLKSEL_ERROR;
> + }
> +
> + return clksel;
> +}
> +
> +static void exynos4212_isol(struct usb2_phy_instance *inst, bool on)
> +{
> + struct usb2_phy_driver *drv = inst->drv;
> + u32 offset;
> + u32 mask;
> + u32 tmp;
> +
> + if (!drv->reg_isol)
> + return;
> +
> + switch (inst->cfg->id) {
> + case EXYNOS4212_DEVICE:
> + offset = EXYNOS_4212_USB_ISOL_OFFSET;
> + mask = EXYNOS_4212_USB_ISOL_OTG;
> + break;
> + case EXYNOS4212_HOST:
> + offset = EXYNOS_4212_USB_ISOL_OFFSET;
> + mask = EXYNOS_4212_USB_ISOL_OTG;
> + break;
> + case EXYNOS4212_HSIC0:
> + offset = EXYNOS_4212_USB_ISOL_HSIC0_OFFSET;
> + mask = EXYNOS_4212_USB_ISOL_HSIC0;
> + break;
> + case EXYNOS4212_HSIC1:
> + offset = EXYNOS_4212_USB_ISOL_HSIC1_OFFSET;
> + mask = EXYNOS_4212_USB_ISOL_HSIC1;
> + break;
> + default:
> + return;
> + };
> +
> + tmp = readl(drv->reg_isol + offset);
> + if (on)
> + tmp &= ~mask;
> + else
> + tmp |= mask;
> + writel(tmp, drv->reg_isol + offset);
> +}
> +
> +static void exynos4212_phy_pwr(struct usb2_phy_instance *inst, bool on)
> +{
> + struct usb2_phy_driver *drv = inst->drv;
> + u32 rstbits = 0;
> + u32 phypwr = 0;
> + u32 rst;
> + u32 pwr;
> +
> + switch (inst->cfg->id) {
> + case EXYNOS4212_DEVICE:
> + phypwr = EXYNOS_4212_UPHYPWR_DEV;
> + rstbits = EXYNOS_4212_URSTCON_DEVICE;
> + break;
> + case EXYNOS4212_HOST:
> + phypwr = EXYNOS_4212_UPHYPWR_HOST;
> + rstbits = EXYNOS_4212_URSTCON_HOST_PHY;
> + break;
> + case EXYNOS4212_HSIC0:
> + phypwr = EXYNOS_4212_UPHYPWR_HSCI0;
> + rstbits = EXYNOS_4212_URSTCON_HSIC1 |
> + EXYNOS_4212_URSTCON_HOST_LINK_P0 |
> + EXYNOS_4212_URSTCON_HOST_PHY;
> + break;
> + case EXYNOS4212_HSIC1:
> + phypwr = EXYNOS_4212_UPHYPWR_HSCI1;
> + rstbits = EXYNOS_4212_URSTCON_HSIC1 |
> + EXYNOS_4212_URSTCON_HOST_LINK_P1;
> + break;
> + };
> +
> + if (on) {
> + writel(inst->clk, drv->reg_phy + EXYNOS_4212_UPHYCLK);
> +
> + pwr = readl(drv->reg_phy + EXYNOS_4212_UPHYPWR);
> + pwr &= ~phypwr;
> + writel(pwr, drv->reg_phy + EXYNOS_4212_UPHYPWR);
> +
> + rst = readl(drv->reg_phy + EXYNOS_4212_UPHYRST);
> + rst |= rstbits;
> + writel(rst, drv->reg_phy + EXYNOS_4212_UPHYRST);
> + udelay(10);
> + rst &= ~rstbits;
> + writel(rst, drv->reg_phy + EXYNOS_4212_UPHYRST);
> + } else {
> + pwr = readl(drv->reg_phy + EXYNOS_4212_UPHYPWR);
> + pwr |= phypwr;
> + writel(pwr, drv->reg_phy + EXYNOS_4212_UPHYPWR);
> + }
> +}
> +
> +static int exynos4212_power_on(struct usb2_phy_instance *inst)
> +{
> + struct usb2_phy_driver *drv = inst->drv;
> +
> + inst->state = STATE_ON;
> + exynos4212_phy_pwr(inst, 1);
> + exynos4212_isol(inst, 0);
> +
> + /* Power on the device, as it is necessary for HSIC to work */
> + if (inst->cfg->id == EXYNOS4212_HSIC0) {
> + struct usb2_phy_instance *device =
> + &drv->usb2_phy_instances[EXYNOS4212_DEVICE];
> + exynos4212_phy_pwr(device, 1);
> + exynos4212_isol(device, 0);
> + }
> +
> + return 0;
> +}
> +
> +static int exynos4212_power_off(struct usb2_phy_instance *inst)
> +{
> + struct usb2_phy_driver *drv = inst->drv;
> + struct usb2_phy_instance *device =
> + &drv->usb2_phy_instances[EXYNOS4212_DEVICE];
> +
> + inst->state = STATE_OFF;
> + exynos4212_isol(inst, 1);
> + exynos4212_phy_pwr(inst, 0);
> +
> + if (inst->cfg->id == EXYNOS4212_HSIC0 && device->state != STATE_ON) {
> + exynos4212_isol(device, 1);
> + exynos4212_phy_pwr(device, 0);
> + }
> +
> + return 0;
> +}
> +
> +
> +static const struct common_phy exynos4212_phys[] = {
> + {
> + .label = "device",
> + .type = PHY_DEVICE,
> + .id = EXYNOS4212_DEVICE,
> + .rate_to_clk = exynos4212_rate_to_clk,
> + .power_on = exynos4212_power_on,
> + .power_off = exynos4212_power_off,
> + },
> + {
> + .label = "host",
> + .type = PHY_HOST,
> + .id = EXYNOS4212_HOST,
> + .rate_to_clk = exynos4212_rate_to_clk,
> + .power_on = exynos4212_power_on,
> + .power_off = exynos4212_power_off,
> + },
> + {
> + .label = "hsic0",
> + .type = PHY_HOST,
> + .id = EXYNOS4212_HSIC0,
> + .rate_to_clk = exynos4212_rate_to_clk,
> + .power_on = exynos4212_power_on,
> + .power_off = exynos4212_power_off,
> + },
> + {
> + .label = "hsic1",
> + .type = PHY_HOST,
> + .id = EXYNOS4212_HSIC1,
> + .rate_to_clk = exynos4212_rate_to_clk,
> + .power_on = exynos4212_power_on,
> + .power_off = exynos4212_power_off,
> + },
> + {},
> +};
> +
> +const struct usb2_phy_config exynos4212_usb2_phy_config = {
> + .num_phys = EXYNOS4212_NUM_PHYS,
> + .phys = exynos4212_phys,
> + .has_mode_switch = 1,
> +};
> +
> --
> 1.7.9.5
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
