On Thu, Oct 31, 2013 at 1:15 PM, Vivek Gautam <gautam.vivek@xxxxxxxxxxx> wrote:
> Add a new driver for the USB 3.0 PHY on Exynos5 series of SoCs.
> The new driver uses the generic PHY framework and will interact
> with DWC3 controller present on Exynos5 series of SoCs.
>
> Signed-off-by: Vivek Gautam <gautam.vivek@xxxxxxxxxxx>
> ---
> .../devicetree/bindings/phy/samsung-phy.txt | 20 +
> drivers/phy/Kconfig | 7 +
> drivers/phy/Makefile | 1 +
> drivers/phy/phy-exynos5-usb3.c | 562 ++++++++++++++++++++
> 4 files changed, 590 insertions(+), 0 deletions(-)
> create mode 100644 drivers/phy/phy-exynos5-usb3.c
>
> diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt
> index c0fccaa..9b5c111 100644
> --- a/Documentation/devicetree/bindings/phy/samsung-phy.txt
> +++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt
> @@ -20,3 +20,23 @@ Required properties:
> - compatible : should be "samsung,exynos5250-dp-video-phy";
> - reg : offset and length of the Display Port PHY register set;
> - #phy-cells : from the generic PHY bindings, must be 0;
> +
> +Samsung Exynos5 SoC seiries USB 3.0 PHY controller
> +--------------------------------------------------
> +
> +Required properties:
> +- compatible :
> + should be "samsung,exynos5250-usb3phy" for exynos5250 SoC
> + should be "samsung,exynos5420-usb3phy" for exynos5420 SoC
> +- reg : Register offset and length array
> + - first field corresponds to USB 3.0 PHY register set;
> + - second field corresponds to PHY power isolation register
> + present in PMU;
> +- clocks: Clock IDs array as required by the controller
> +- clock-names: names of clocks correseponding to IDs in the clock property;
> + Required clocks:
> + - first clock is main PHY clock (same as USB 3.0 controller IP clock)
> + - second clock is reference clock (usually crystal clock)
> + optional clock:
> + - third clock is special clock used by PHY for operation
> +- #phy-cells : from the generic PHY bindings, must be 0;
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index a344f3d..9a100c6 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -51,4 +51,11 @@ config PHY_EXYNOS_DP_VIDEO
> help
> Support for Display Port PHY found on Samsung EXYNOS SoCs.
>
> +config PHY_EXYNOS5_USB3
> + tristate "Exynos5 SoC series USB 3.0 PHY driver"
> + depends on ARCH_EXYNOS5
> + select GENERIC_PHY
> + help
> + Enable USB 3.0 PHY support for Exynos 5 SoC series
> +
> endmenu
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index d0caae9..9c06a61 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -7,3 +7,4 @@ obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO) += phy-exynos-dp-video.o
> obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO) += phy-exynos-mipi-video.o
> obj-$(CONFIG_OMAP_USB2) += phy-omap-usb2.o
> obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o
> +obj-$(CONFIG_PHY_EXYNOS5_USB3) += phy-exynos5-usb3.o
> diff --git a/drivers/phy/phy-exynos5-usb3.c b/drivers/phy/phy-exynos5-usb3.c
> new file mode 100644
> index 0000000..b9a2674
> --- /dev/null
> +++ b/drivers/phy/phy-exynos5-usb3.c
> @@ -0,0 +1,562 @@
> +/*
> + * Samsung EXYNOS5 SoC series USB 3.0 PHY driver
> + *
> + * Copyright (C) 2013 Samsung Electronics Co., Ltd.
> + * Author: Vivek Gautam <gautam.vivek@xxxxxxxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/mutex.h>
> +
> +/* Exynos USB PHY registers */
> +#define EXYNOS5_FSEL_9MHZ6 0x0
> +#define EXYNOS5_FSEL_10MHZ 0x1
> +#define EXYNOS5_FSEL_12MHZ 0x2
> +#define EXYNOS5_FSEL_19MHZ2 0x3
> +#define EXYNOS5_FSEL_20MHZ 0x4
> +#define EXYNOS5_FSEL_24MHZ 0x5
> +#define EXYNOS5_FSEL_50MHZ 0x7
> +
> +/* EXYNOS5: USB 3.0 DRD PHY registers */
> +#define EXYNOS5_DRD_LINKSYSTEM (0x04)
> +
> +#define LINKSYSTEM_FLADJ_MASK (0x3f << 1)
> +#define LINKSYSTEM_FLADJ(_x) ((_x) << 1)
> +#define LINKSYSTEM_XHCI_VERSION_CONTROL (0x1 << 27)
> +
> +#define EXYNOS5_DRD_PHYUTMI (0x08)
> +
> +#define PHYUTMI_OTGDISABLE (0x1 << 6)
> +#define PHYUTMI_FORCESUSPEND (0x1 << 1)
> +#define PHYUTMI_FORCESLEEP (0x1 << 0)
> +
> +#define EXYNOS5_DRD_PHYPIPE (0x0c)
> +
> +#define EXYNOS5_DRD_PHYCLKRST (0x10)
> +
> +#define PHYCLKRST_SSC_REFCLKSEL_MASK (0xff << 23)
> +#define PHYCLKRST_SSC_REFCLKSEL(_x) ((_x) << 23)
> +
> +#define PHYCLKRST_SSC_RANGE_MASK (0x03 << 21)
> +#define PHYCLKRST_SSC_RANGE(_x) ((_x) << 21)
> +
> +#define PHYCLKRST_SSC_EN (0x1 << 20)
> +#define PHYCLKRST_REF_SSP_EN (0x1 << 19)
> +#define PHYCLKRST_REF_CLKDIV2 (0x1 << 18)
> +
> +#define PHYCLKRST_MPLL_MULTIPLIER_MASK (0x7f << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_100MHZ_REF (0x19 << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_50M_REF (0x02 << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF (0x68 << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF (0x7d << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF (0x02 << 11)
> +
> +#define PHYCLKRST_FSEL_MASK (0x3f << 5)
> +#define PHYCLKRST_FSEL(_x) ((_x) << 5)
> +#define PHYCLKRST_FSEL_PAD_100MHZ (0x27 << 5)
> +#define PHYCLKRST_FSEL_PAD_24MHZ (0x2a << 5)
> +#define PHYCLKRST_FSEL_PAD_20MHZ (0x31 << 5)
> +#define PHYCLKRST_FSEL_PAD_19_2MHZ (0x38 << 5)
> +
> +#define PHYCLKRST_RETENABLEN (0x1 << 4)
> +
> +#define PHYCLKRST_REFCLKSEL_MASK (0x03 << 2)
> +#define PHYCLKRST_REFCLKSEL_PAD_REFCLK (0x2 << 2)
> +#define PHYCLKRST_REFCLKSEL_EXT_REFCLK (0x3 << 2)
> +
> +#define PHYCLKRST_PORTRESET (0x1 << 1)
> +#define PHYCLKRST_COMMONONN (0x1 << 0)
> +
> +#define EXYNOS5_DRD_PHYREG0 (0x14)
> +#define EXYNOS5_DRD_PHYREG1 (0x18)
> +
> +#define EXYNOS5_DRD_PHYPARAM0 (0x1c)
> +
> +#define PHYPARAM0_REF_USE_PAD (0x1 << 31)
> +#define PHYPARAM0_REF_LOSLEVEL_MASK (0x1f << 26)
> +#define PHYPARAM0_REF_LOSLEVEL (0x9 << 26)
> +
> +#define EXYNOS5_DRD_PHYPARAM1 (0x20)
> +
> +#define PHYPARAM1_PCS_TXDEEMPH_MASK (0x1f << 0)
> +#define PHYPARAM1_PCS_TXDEEMPH (0x1c)
> +
> +#define EXYNOS5_DRD_PHYTERM (0x24)
> +
> +#define EXYNOS5_DRD_PHYTEST (0x28)
> +
> +#define PHYTEST_POWERDOWN_SSP (0x1 << 3)
> +#define PHYTEST_POWERDOWN_HSP (0x1 << 2)
> +
> +#define EXYNOS5_DRD_PHYADP (0x2c)
> +
> +#define EXYNOS5_DRD_PHYBATCHG (0x30)
> +
> +#define PHYBATCHG_UTMI_CLKSEL (0x1 << 2)
> +
> +#define EXYNOS5_DRD_PHYRESUME (0x34)
> +#define EXYNOS5_DRD_LINKPORT (0x44)
> +
> +
> +/* Isolation, configured in the power management unit */
> +#define EXYNOS5_USB_ISOL_DRD (1 << 0)
> +
> +#define CLKSEL_ERROR -1
> +
> +#ifndef KHZ
> +#define KHZ 1000
> +#endif
> +
> +#ifndef MHZ
> +#define MHZ (KHZ * KHZ)
> +#endif
> +
> +enum samsung_cpu_type {
> + TYPE_EXYNOS5250,
> + TYPE_EXYNOS5420,
> +};
> +
> +enum usb3phy_state {
> + STATE_OFF,
> + STATE_ON,
> +};
> +
> +struct usb3phy_config {
> + enum samsung_cpu_type cpu;
> + bool has_sclk_usbphy30;
> +};
> +
> +struct usb3phy_instance {
> + char *label;
> + struct usb3phy_driver *drv;
> + struct phy *phy;
> + enum usb3phy_state state;
> + u32 clk;
> + unsigned long rate;
> +};
> +
> +struct usb3phy_driver {
> + struct device *dev;
> + void __iomem *reg_phy;
> + void __iomem *reg_isol;
> + struct clk *clk;
> + struct clk *sclk_usbphy30;
> + struct usb3phy_instance instance;
> +};
> +
> +/*
> + * exynos5_rate_to_clk() converts the supplied clock rate to the value that
> + * can be written to the phy register.
> + */
> +static u32 exynos5_rate_to_clk(unsigned long rate)
> +{
> + unsigned int clksel;
> +
> + /* EXYNOS5_FSEL_MASK */
> +
> + switch (rate) {
> + case 9600 * KHZ:
> + clksel = EXYNOS5_FSEL_9MHZ6;
> + break;
> + case 10 * MHZ:
> + clksel = EXYNOS5_FSEL_10MHZ;
> + break;
> + case 12 * MHZ:
> + clksel = EXYNOS5_FSEL_12MHZ;
> + break;
> + case 19200 * KHZ:
> + clksel = EXYNOS5_FSEL_19MHZ2;
> + break;
> + case 20 * MHZ:
> + clksel = EXYNOS5_FSEL_20MHZ;
> + break;
> + case 24 * MHZ:
> + clksel = EXYNOS5_FSEL_24MHZ;
> + break;
> + case 50 * MHZ:
> + clksel = EXYNOS5_FSEL_50MHZ;
> + break;
> + default:
> + clksel = CLKSEL_ERROR;
> + }
> +
> + return clksel;
> +}
> +
> +static void exynos5_usb3phy_isol(struct usb3phy_instance *inst, bool on)
> +{
> + struct usb3phy_driver *drv = inst->drv;
> + u32 tmp;
> +
> + if (!drv->reg_isol)
> + return;
> +
> + tmp = readl(drv->reg_isol);
> + if (on)
> + tmp &= ~EXYNOS5_USB_ISOL_DRD;
> + else
> + tmp |= EXYNOS5_USB_ISOL_DRD;
> + writel(tmp, drv->reg_isol);
> +}
> +
> +/*
> + * Sets the phy clk as EXTREFCLK (XXTI) which is internal clock from clock core.
> + */
> +static u32 exynos5_usb3phy_set_refclk(struct usb3phy_instance *inst)
> +{
> + u32 reg;
> + u32 refclk;
> +
> + refclk = inst->clk;
> +
> + reg = PHYCLKRST_REFCLKSEL_EXT_REFCLK |
> + PHYCLKRST_FSEL(refclk);
> +
> + switch (refclk) {
> + case EXYNOS5_FSEL_50MHZ:
> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_50M_REF |
> + PHYCLKRST_SSC_REFCLKSEL(0x00));
> + break;
> + case EXYNOS5_FSEL_20MHZ:
> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF |
> + PHYCLKRST_SSC_REFCLKSEL(0x00));
> + break;
> + case EXYNOS5_FSEL_19MHZ2:
> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF |
> + PHYCLKRST_SSC_REFCLKSEL(0x88));
> + break;
> + case EXYNOS5_FSEL_24MHZ:
> + default:
> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF |
> + PHYCLKRST_SSC_REFCLKSEL(0x88));
> + break;
> + }
> +
> + return reg;
> +}
> +
> +static void exynos5_usb3phy_init(struct usb3phy_instance *inst)
> +{
> + struct usb3phy_driver *drv = inst->drv;
> + u32 phyparam0;
> + u32 phyparam1;
> + u32 linksystem;
> + u32 phybatchg;
> + u32 phytest;
> + u32 phyclkrst;
> +
> + /* Reset USB 3.0 PHY */
> + writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYREG0);
> +
> + phyparam0 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM0);
> + /* Select PHY CLK source */
> + phyparam0 &= ~PHYPARAM0_REF_USE_PAD;
> + /* Set Loss-of-Signal Detector sensitivity */
> + phyparam0 &= ~PHYPARAM0_REF_LOSLEVEL_MASK;
> + phyparam0 |= PHYPARAM0_REF_LOSLEVEL;
> + writel(phyparam0, drv->reg_phy + EXYNOS5_DRD_PHYPARAM0);
> +
> + writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYRESUME);
> +
> + /*
> + * Setting the Frame length Adj value[6:1] to default 0x20
> + * See xHCI 1.0 spec, 5.2.4
> + */
> + linksystem = LINKSYSTEM_XHCI_VERSION_CONTROL |
> + LINKSYSTEM_FLADJ(0x20);
> + writel(linksystem, drv->reg_phy + EXYNOS5_DRD_LINKSYSTEM);
> +
> + phyparam1 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM1);
> + /* Set Tx De-Emphasis level */
> + phyparam1 &= ~PHYPARAM1_PCS_TXDEEMPH_MASK;
> + phyparam1 |= PHYPARAM1_PCS_TXDEEMPH;
> + writel(phyparam1, drv->reg_phy + EXYNOS5_DRD_PHYPARAM1);
> +
> + phybatchg = readl(drv->reg_phy + EXYNOS5_DRD_PHYBATCHG);
> + phybatchg |= PHYBATCHG_UTMI_CLKSEL;
> + writel(phybatchg, drv->reg_phy + EXYNOS5_DRD_PHYBATCHG);
> +
> + /* PHYTEST POWERDOWN Control */
> + phytest = readl(drv->reg_phy + EXYNOS5_DRD_PHYTEST);
> + phytest &= ~(PHYTEST_POWERDOWN_SSP |
> + PHYTEST_POWERDOWN_HSP);
> + writel(phytest, drv->reg_phy + EXYNOS5_DRD_PHYTEST);
> +
> + /* UTMI Power Control */
> + writel(PHYUTMI_OTGDISABLE, drv->reg_phy + EXYNOS5_DRD_PHYUTMI);
> +
> + phyclkrst = exynos5_usb3phy_set_refclk(inst);
> +
> + phyclkrst |= PHYCLKRST_PORTRESET |
> + /* Digital power supply in normal operating mode */
> + PHYCLKRST_RETENABLEN |
> + /* Enable ref clock for SS function */
> + PHYCLKRST_REF_SSP_EN |
> + /* Enable spread spectrum */
> + PHYCLKRST_SSC_EN |
> + /* Power down HS Bias and PLL blocks in suspend mode */
> + PHYCLKRST_COMMONONN;
> +
> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
> +
> + udelay(10);
> +
> + phyclkrst &= ~PHYCLKRST_PORTRESET;
> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
> +
> +}
> +
> +static void exynos5_usb3phy_exit(struct usb3phy_instance *inst)
> +{
> + struct usb3phy_driver *drv = inst->drv;
> + u32 phyutmi;
> + u32 phyclkrst;
> + u32 phytest;
> +
> + phyutmi = PHYUTMI_OTGDISABLE |
> + PHYUTMI_FORCESUSPEND |
> + PHYUTMI_FORCESLEEP;
> + writel(phyutmi, drv->reg_phy + EXYNOS5_DRD_PHYUTMI);
> +
> + /* Resetting the PHYCLKRST enable bits to reduce leakage current */
> + phyclkrst = readl(drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
> + phyclkrst &= ~(PHYCLKRST_REF_SSP_EN |
> + PHYCLKRST_SSC_EN |
> + PHYCLKRST_COMMONONN);
> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
> +
> + /* Control PHYTEST to remove leakage current */
> + phytest = readl(drv->reg_phy + EXYNOS5_DRD_PHYTEST);
> + phytest |= PHYTEST_POWERDOWN_SSP |
> + PHYTEST_POWERDOWN_HSP;
> + writel(phytest, drv->reg_phy + EXYNOS5_DRD_PHYTEST);
> +}
> +
> +static int exynos5_usb3phy_power_on(struct phy *phy)
> +{
> + struct usb3phy_instance *inst = phy_get_drvdata(phy);
> + struct usb3phy_driver *drv = inst->drv;
> + int ret;
> +
> + dev_info(drv->dev, "Request to power_on \"%s\" usb phy\n",
> + inst->label);
> +
> + if (drv->sclk_usbphy30)
> + clk_prepare_enable(drv->sclk_usbphy30);
> +
> + ret = clk_prepare_enable(drv->clk);
> + if (ret)
> + return ret;
> +
> + if (inst->state == STATE_ON) {
> + dev_err(drv->dev, "usb phy \"%s\" already on",
> + inst->label);
> + ret = -ENODEV;
> + goto err0;
> + }
> +
> + inst->state = STATE_ON;
> +
> + /* Initialize the PHY and power it ON */
> + exynos5_usb3phy_init(inst);
I think with the above one, we are deviating from the generic PHY framework.
phy init supposed to be called from actual dwc3 core driver. dwc3
core driver has
phy_ops->init to do this .
@Kishon: Please correct me if i am wrong.
> + exynos5_usb3phy_isol(inst, 0);
> +
> +err0:
> + clk_disable_unprepare(drv->clk);
> +
> + return ret;
> +}
> +
> +static int exynos5_usb3phy_power_off(struct phy *phy)
> +{
> + struct usb3phy_instance *inst = phy_get_drvdata(phy);
> + struct usb3phy_driver *drv = inst->drv;
> + int ret;
> +
> + dev_info(drv->dev, "Request to power_off \"%s\" usb phy\n",
> + inst->label);
> + ret = clk_prepare_enable(drv->clk);
> + if (ret)
> + return ret;
> +
> + if (inst->state == STATE_OFF) {
> + dev_err(drv->dev, "usb phy \"%s\" already off",
> + inst->label);
> + ret = -ENODEV;
> + goto err0;
> + }
> +
> + inst->state = STATE_OFF;
> +
> + /* Power-off the PHY and de-initialize it */
> + exynos5_usb3phy_isol(inst, 1);
> + exynos5_usb3phy_exit(inst);
> +
> +err0:
> + clk_disable_unprepare(drv->clk);
> + if (drv->sclk_usbphy30)
> + clk_disable_unprepare(drv->sclk_usbphy30);
> +
> + return ret;
> +}
> +
> +static struct phy_ops exynos5_usb3phy_ops = {
> + .power_on = exynos5_usb3phy_power_on,
> + .power_off = exynos5_usb3phy_power_off,
> + .owner = THIS_MODULE,
> +};
> +
> +static const struct of_device_id exynos5_usb3phy_of_match[];
> +
> +static int exynos5_usb3phy_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct usb3phy_driver *drv;
> + struct usb3phy_instance *inst;
> + struct phy_provider *phy_provider;
> + struct resource *res;
> + struct clk *clk;
> + const struct of_device_id *match;
> + const struct usb3phy_config *cfg;
> +
> + match = of_match_node(exynos5_usb3phy_of_match, pdev->dev.of_node);
> + if (!match) {
> + dev_err(dev, "of_match_node() failed\n");
> + return -EINVAL;
> + }
> + cfg = match->data;
> + if (!cfg) {
> + dev_err(dev, "Failed to get configuration\n");
> + return -EINVAL;
> + }
> +
> + drv = devm_kzalloc(dev, sizeof(struct usb3phy_driver), GFP_KERNEL);
> + if (!drv) {
> + dev_err(dev, "Failed to allocate memory\n");
> + return -ENOMEM;
> + }
> +
> + dev_set_drvdata(dev, drv);
> + drv->dev = dev;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + drv->reg_phy = devm_ioremap_resource(dev, res);
> + if (IS_ERR(drv->reg_phy)) {
> + dev_err(dev, "Failed to map register memory (phy)\n");
> + return PTR_ERR(drv->reg_phy);
> + }
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> + drv->reg_isol = devm_ioremap_resource(dev, res);
> + if (IS_ERR(drv->reg_isol)) {
> + dev_err(dev, "Failed to map register memory (isolation)\n");
> + return PTR_ERR(drv->reg_isol);
> + }
> +
> + phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> + if (IS_ERR(phy_provider)) {
> + dev_err(drv->dev, "Failed to register phy provider\n");
> + return PTR_ERR(phy_provider);
> + }
> +
> + drv->clk = devm_clk_get(dev, "phy");
> + if (IS_ERR(drv->clk)) {
> + dev_err(dev, "Failed to get clock of phy controller\n");
> + return PTR_ERR(drv->clk);
> + }
> +
> + /*
> + * Exysno5420 SoC has an additional special clock, used for
> + * for USB 3.0 PHY operation, this clock goes to the PHY block
> + * as a reference clock to clock generation block of the controller.
> + */
> + if (cfg->has_sclk_usbphy30) {
> + drv->sclk_usbphy30 = devm_clk_get(dev, "sclk_usbphy30");
> + if (IS_ERR(drv->clk)) {
> + dev_err(dev, "Failed to get phy reference clock\n");
> + return PTR_ERR(drv->clk);
> + }
> + }
> +
> + inst = &drv->instance;
> + inst->drv = drv;
> + inst->label = "usb3drd";
> +
> + dev_info(dev, "Creating phy \"%s\"\n", inst->label);
> + inst->phy = devm_phy_create(dev, &exynos5_usb3phy_ops, NULL);
> + if (IS_ERR(inst->phy)) {
> + dev_err(drv->dev, "Failed to create usb3phy \"%s\"\n",
> + inst->label);
> + return PTR_ERR(inst->phy);
> + }
> +
> + phy_set_drvdata(inst->phy, inst);
> +
> + clk = clk_get(dev, inst->label);
> + if (IS_ERR(clk)) {
> + dev_err(dev, "Failed to get clock of \"%s\" phy\n",
> + inst->label);
> + return PTR_ERR(clk);
> + }
> +
> + inst->rate = clk_get_rate(clk);
> +
> + inst->clk = exynos5_rate_to_clk(inst->rate);
> + if (inst->clk == CLKSEL_ERROR) {
> + dev_err(dev, "Clock rate (%ld) not supported\n",
> + inst->rate);
> + clk_put(clk);
> + return -EINVAL;
> + }
> + clk_put(clk);
> +
> + return 0;
> +}
> +
> +const struct usb3phy_config exynos5420_usb3phy_cfg = {
> + .cpu = TYPE_EXYNOS5420,
> + .has_sclk_usbphy30 = true,
> +};
> +
> +const struct usb3phy_config exynos5250_usb3phy_cfg = {
> + .cpu = TYPE_EXYNOS5250,
> + .has_sclk_usbphy30 = false,
> +};
> +
> +static const struct of_device_id exynos5_usb3phy_of_match[] = {
> + {
> + .compatible = "samsung,exynos5250-usb3phy",
> + .data = &exynos5250_usb3phy_cfg
> + }, {
> + .compatible = "samsung,exynos5420-usb3phy",
> + .data = &exynos5420_usb3phy_cfg
> + },
> + { },
> +};
> +
> +static struct platform_driver exynos5_usb3phy_driver = {
> + .probe = exynos5_usb3phy_probe,
> + .driver = {
> + .of_match_table = exynos5_usb3phy_of_match,
> + .name = "exynos5-usb3phy",
> + .owner = THIS_MODULE,
> + }
> +};
> +
> +module_platform_driver(exynos5_usb3phy_driver);
> +MODULE_DESCRIPTION("Samsung EXYNOS5 series SoC USB 3.0 PHY driver");
> +MODULE_AUTHOR("Vivek Gautam <gautam.vivek@xxxxxxxxxxx>");
> +MODULE_LICENSE("GPL v2");
> +MODULE_ALIAS("platform:exynos5-usb3phy");
> --
> 1.7.6.5
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
