On Thu, 16 May 2013, Vinod Koul wrote:
> On Wed, May 15, 2013 at 10:51:25AM +0100, Lee Jones wrote:
> > All configuration left in d40_phy_cfg() is runtime configurable and
> > there is already a call into it from d40_runtime_config(), so let's
> > rely on that.
> >
> > Acked-by: Vinod Koul <vnod.koul@xxxxxxxxx>
> That needs up update!
Ah, where did I get that from that?
Was that my mistake, or was this in the MAINTAINERS file?
> > Acked-by: Arnd Bergmann <arnd@xxxxxxxx>
> > Signed-off-by: Lee Jones <lee.jones@xxxxxxxxxx>
> > ---
> > drivers/dma/ste_dma40.c | 14 +++---
> > drivers/dma/ste_dma40_ll.c | 101 +++++++++++++++++++++-----------------------
> > drivers/dma/ste_dma40_ll.h | 3 +-
> > 3 files changed, 58 insertions(+), 60 deletions(-)
> >
> > diff --git a/drivers/dma/ste_dma40.c b/drivers/dma/ste_dma40.c
> > index 759293e..b7fe46b 100644
> > --- a/drivers/dma/ste_dma40.c
> > +++ b/drivers/dma/ste_dma40.c
> > @@ -2043,6 +2043,14 @@ static int d40_config_memcpy(struct d40_chan *d40c)
> > } else if (dma_has_cap(DMA_MEMCPY, cap) &&
> > dma_has_cap(DMA_SLAVE, cap)) {
> > d40c->dma_cfg = dma40_memcpy_conf_phy;
> > +
> > + /* Generate interrrupt at end of transfer or relink. */
> > + d40c->dst_def_cfg |= BIT(D40_SREG_CFG_TIM_POS);
> > +
> > + /* Generate interrupt on error. */
> > + d40c->src_def_cfg |= BIT(D40_SREG_CFG_EIM_POS);
> > + d40c->dst_def_cfg |= BIT(D40_SREG_CFG_EIM_POS);
> > +
> > } else {
> > chan_err(d40c, "No memcpy\n");
> > return -EINVAL;
> > @@ -2496,9 +2504,6 @@ static int d40_alloc_chan_resources(struct dma_chan *chan)
> > }
> >
> > pm_runtime_get_sync(d40c->base->dev);
> > - /* Fill in basic CFG register values */
> > - d40_phy_cfg(&d40c->dma_cfg, &d40c->src_def_cfg,
> > - &d40c->dst_def_cfg, chan_is_logical(d40c));
> >
> > d40_set_prio_realtime(d40c);
> >
> > @@ -2862,8 +2867,7 @@ static int d40_set_runtime_config(struct dma_chan *chan,
> > if (chan_is_logical(d40c))
> > d40_log_cfg(cfg, &d40c->log_def.lcsp1, &d40c->log_def.lcsp3);
> > else
> > - d40_phy_cfg(cfg, &d40c->src_def_cfg,
> > - &d40c->dst_def_cfg, false);
> > + d40_phy_cfg(cfg, &d40c->src_def_cfg, &d40c->dst_def_cfg);
> >
> > /* These settings will take precedence later */
> > d40c->runtime_addr = config_addr;
> > diff --git a/drivers/dma/ste_dma40_ll.c b/drivers/dma/ste_dma40_ll.c
> > index 435a223..ab5a2a7 100644
> > --- a/drivers/dma/ste_dma40_ll.c
> > +++ b/drivers/dma/ste_dma40_ll.c
> > @@ -50,63 +50,58 @@ void d40_log_cfg(struct stedma40_chan_cfg *cfg,
> >
> > }
> >
> > -/* Sets up SRC and DST CFG register for both logical and physical channels */
> > -void d40_phy_cfg(struct stedma40_chan_cfg *cfg,
> > - u32 *src_cfg, u32 *dst_cfg, bool is_log)
> > +void d40_phy_cfg(struct stedma40_chan_cfg *cfg, u32 *src_cfg, u32 *dst_cfg)
> > {
> > u32 src = 0;
> > u32 dst = 0;
> >
> > - if (!is_log) {
> > - /* Physical channel */
> > - if ((cfg->dir == STEDMA40_PERIPH_TO_MEM) ||
> > - (cfg->dir == STEDMA40_PERIPH_TO_PERIPH)) {
> > - /* Set master port to 1 */
> > - src |= 1 << D40_SREG_CFG_MST_POS;
> > - src |= D40_TYPE_TO_EVENT(cfg->dev_type);
> > -
> > - if (cfg->src_info.flow_ctrl == STEDMA40_NO_FLOW_CTRL)
> > - src |= 1 << D40_SREG_CFG_PHY_TM_POS;
> > - else
> > - src |= 3 << D40_SREG_CFG_PHY_TM_POS;
> > - }
> > - if ((cfg->dir == STEDMA40_MEM_TO_PERIPH) ||
> > - (cfg->dir == STEDMA40_PERIPH_TO_PERIPH)) {
> > - /* Set master port to 1 */
> > - dst |= 1 << D40_SREG_CFG_MST_POS;
> > - dst |= D40_TYPE_TO_EVENT(cfg->dev_type);
> > -
> > - if (cfg->dst_info.flow_ctrl == STEDMA40_NO_FLOW_CTRL)
> > - dst |= 1 << D40_SREG_CFG_PHY_TM_POS;
> > - else
> > - dst |= 3 << D40_SREG_CFG_PHY_TM_POS;
> > - }
> > - /* Interrupt on end of transfer for destination */
> > - dst |= 1 << D40_SREG_CFG_TIM_POS;
> > -
> > - /* Generate interrupt on error */
> > - src |= 1 << D40_SREG_CFG_EIM_POS;
> > - dst |= 1 << D40_SREG_CFG_EIM_POS;
> > -
> > - /* PSIZE */
> > - if (cfg->src_info.psize != STEDMA40_PSIZE_PHY_1) {
> > - src |= 1 << D40_SREG_CFG_PHY_PEN_POS;
> > - src |= cfg->src_info.psize << D40_SREG_CFG_PSIZE_POS;
> > - }
> > - if (cfg->dst_info.psize != STEDMA40_PSIZE_PHY_1) {
> > - dst |= 1 << D40_SREG_CFG_PHY_PEN_POS;
> > - dst |= cfg->dst_info.psize << D40_SREG_CFG_PSIZE_POS;
> > - }
> > -
> > - /* Element size */
> > - src |= cfg->src_info.data_width << D40_SREG_CFG_ESIZE_POS;
> > - dst |= cfg->dst_info.data_width << D40_SREG_CFG_ESIZE_POS;
> > -
> > - /* Set the priority bit to high for the physical channel */
> > - if (cfg->high_priority) {
> > - src |= 1 << D40_SREG_CFG_PRI_POS;
> > - dst |= 1 << D40_SREG_CFG_PRI_POS;
> > - }
> > + if ((cfg->dir == STEDMA40_PERIPH_TO_MEM) ||
> > + (cfg->dir == STEDMA40_PERIPH_TO_PERIPH)) {
> > + /* Set master port to 1 */
> > + src |= 1 << D40_SREG_CFG_MST_POS;
> > + src |= D40_TYPE_TO_EVENT(cfg->dev_type);
> > +
> > + if (cfg->src_info.flow_ctrl == STEDMA40_NO_FLOW_CTRL)
> > + src |= 1 << D40_SREG_CFG_PHY_TM_POS;
> > + else
> > + src |= 3 << D40_SREG_CFG_PHY_TM_POS;
> > + }
> > + if ((cfg->dir == STEDMA40_MEM_TO_PERIPH) ||
> > + (cfg->dir == STEDMA40_PERIPH_TO_PERIPH)) {
> > + /* Set master port to 1 */
> > + dst |= 1 << D40_SREG_CFG_MST_POS;
> > + dst |= D40_TYPE_TO_EVENT(cfg->dev_type);
> > +
> > + if (cfg->dst_info.flow_ctrl == STEDMA40_NO_FLOW_CTRL)
> > + dst |= 1 << D40_SREG_CFG_PHY_TM_POS;
> > + else
> > + dst |= 3 << D40_SREG_CFG_PHY_TM_POS;
> > + }
> > + /* Interrupt on end of transfer for destination */
> > + dst |= 1 << D40_SREG_CFG_TIM_POS;
> > +
> > + /* Generate interrupt on error */
> > + src |= 1 << D40_SREG_CFG_EIM_POS;
> > + dst |= 1 << D40_SREG_CFG_EIM_POS;
> > +
> > + /* PSIZE */
> > + if (cfg->src_info.psize != STEDMA40_PSIZE_PHY_1) {
> > + src |= 1 << D40_SREG_CFG_PHY_PEN_POS;
> > + src |= cfg->src_info.psize << D40_SREG_CFG_PSIZE_POS;
> > + }
> > + if (cfg->dst_info.psize != STEDMA40_PSIZE_PHY_1) {
> > + dst |= 1 << D40_SREG_CFG_PHY_PEN_POS;
> > + dst |= cfg->dst_info.psize << D40_SREG_CFG_PSIZE_POS;
> > + }
> > +
> > + /* Element size */
> > + src |= cfg->src_info.data_width << D40_SREG_CFG_ESIZE_POS;
> > + dst |= cfg->dst_info.data_width << D40_SREG_CFG_ESIZE_POS;
> > +
> > + /* Set the priority bit to high for the physical channel */
> > + if (cfg->high_priority) {
> > + src |= 1 << D40_SREG_CFG_PRI_POS;
> > + dst |= 1 << D40_SREG_CFG_PRI_POS;
> > }
> >
> > if (cfg->src_info.big_endian)
> > diff --git a/drivers/dma/ste_dma40_ll.h b/drivers/dma/ste_dma40_ll.h
> > index fdde8ef..1b47312 100644
> > --- a/drivers/dma/ste_dma40_ll.h
> > +++ b/drivers/dma/ste_dma40_ll.h
> > @@ -432,8 +432,7 @@ enum d40_lli_flags {
> >
> > void d40_phy_cfg(struct stedma40_chan_cfg *cfg,
> > u32 *src_cfg,
> > - u32 *dst_cfg,
> > - bool is_log);
> > + u32 *dst_cfg);
> >
> > void d40_log_cfg(struct stedma40_chan_cfg *cfg,
> > u32 *lcsp1,
--
Lee Jones
Linaro ST-Ericsson Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
