Hi,
>
> Hi,
> > On Tue, Jul 10, 2012 at 11:35 AM, Gupta, Ajay Kumar <ajay.gupta@xxxxxx>
> > wrote:
> > > Hi,
> > >>
> > >> On Mon, Jul 9, 2012 at 7:18 PM, Damodar Santhapuri <x0132156@xxxxxx>
> > >> wrote:
> > >> > From: Ajay Kumar Gupta <ajay.gupta@xxxxxx>
> > >> >
> > >> > AM335x uses NOP transceiver driver and need to enable builtin PHY
> > >> > by writing into usb_ctrl register available in system control
> > >> > module register space. This is being added at musb glue driver
> > >> > layer untill a separate system control module driver is available.
> > >> >
> > >> > Signed-off-by: Ajay Kumar Gupta <ajay.gupta@xxxxxx>
> > >> > Signed-off-by: Damodar Santhapuri <x0132156@xxxxxx>
> > >> > ---
> > >> > arch/arm/mach-omap2/board-ti8168evm.c | 1 -
> > >> > arch/arm/mach-omap2/omap_phy_internal.c | 35 ------------
> > >> > arch/arm/plat-omap/include/plat/usb.h | 5 +-
> > >> > drivers/usb/musb/musb_dsps.c | 88
> > >> +++++++++++++++++++++++++------
> > >> > 4 files changed, 74 insertions(+), 55 deletions(-)
> > >> >
> > >> > diff --git a/arch/arm/mach-omap2/board-ti8168evm.c
> > b/arch/arm/mach-
> > >> omap2/board-ti8168evm.c
> > >> > index d4c8392..0c7c098 100644
> > >> > --- a/arch/arm/mach-omap2/board-ti8168evm.c
> > >> > +++ b/arch/arm/mach-omap2/board-ti8168evm.c
> > >> > @@ -26,7 +26,6 @@
> > >> > #include <plat/usb.h>
> > >> >
> > >> > static struct omap_musb_board_data musb_board_data = {
> > >> > - .set_phy_power = ti81xx_musb_phy_power,
> > >> > .interface_type = MUSB_INTERFACE_ULPI,
> > >> > .mode = MUSB_OTG,
> > >> > .power = 500,
> > >> > diff --git a/arch/arm/mach-omap2/omap_phy_internal.c
> > b/arch/arm/mach-
> > >> omap2/omap_phy_internal.c
> > >> > index d52651a..d80bb16 100644
> > >> > --- a/arch/arm/mach-omap2/omap_phy_internal.c
> > >> > +++ b/arch/arm/mach-omap2/omap_phy_internal.c
> > >> > @@ -254,38 +254,3 @@ void am35x_set_mode(u8 musb_mode)
> > >> >
> > >> > omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);
> > >> > }
> > >> > -
> > >> > -void ti81xx_musb_phy_power(u8 on)
> > >> > -{
> > >> > - void __iomem *scm_base = NULL;
> > >> > - u32 usbphycfg;
> > >> > -
> > >> > - scm_base = ioremap(TI81XX_SCM_BASE, SZ_2K);
> > >> > - if (!scm_base) {
> > >> > - pr_err("system control module ioremap failed\n");
> > >> > - return;
> > >> > - }
> > >> > -
> > >> > - usbphycfg = __raw_readl(scm_base + USBCTRL0);
> > >> > -
> > >> > - if (on) {
> > >> > - if (cpu_is_ti816x()) {
> > >> > - usbphycfg |= TI816X_USBPHY0_NORMAL_MODE;
> > >> > - usbphycfg &= ~TI816X_USBPHY_REFCLK_OSC;
> > >> > - } else if (cpu_is_ti814x()) {
> > >> > - usbphycfg &= ~(USBPHY_CM_PWRDN |
> > >> USBPHY_OTG_PWRDN
> > >> > - | USBPHY_DPINPUT |
> > USBPHY_DMINPUT);
> > >> > - usbphycfg |= (USBPHY_OTGVDET_EN |
> > >> USBPHY_OTGSESSEND_EN
> > >> > - | USBPHY_DPOPBUFCTL |
> > >> USBPHY_DMOPBUFCTL);
> > >> > - }
> > >> > - } else {
> > >> > - if (cpu_is_ti816x())
> > >> > - usbphycfg &= ~TI816X_USBPHY0_NORMAL_MODE;
> > >> > - else if (cpu_is_ti814x())
> > >> > - usbphycfg |= USBPHY_CM_PWRDN |
> > >> USBPHY_OTG_PWRDN;
> > >> > -
> > >> > - }
> > >> > - __raw_writel(usbphycfg, scm_base + USBCTRL0);
> > >> > -
> > >> > - iounmap(scm_base);
> > >> > -}
> > >> > diff --git a/arch/arm/plat-omap/include/plat/usb.h
> > b/arch/arm/plat-
> > >> omap/include/plat/usb.h
> > >> > index 548a4c8..c2aa4ae 100644
> > >> > --- a/arch/arm/plat-omap/include/plat/usb.h
> > >> > +++ b/arch/arm/plat-omap/include/plat/usb.h
> > >> > @@ -95,7 +95,6 @@ extern void am35x_musb_reset(void);
> > >> > extern void am35x_musb_phy_power(u8 on);
> > >> > extern void am35x_musb_clear_irq(void);
> > >> > extern void am35x_set_mode(u8 musb_mode);
> > >> > -extern void ti81xx_musb_phy_power(u8 on);
> > >> >
> > >> > /* AM35x */
> > >> > /* USB 2.0 PHY Control */
> > >> > @@ -120,8 +119,8 @@ extern void ti81xx_musb_phy_power(u8 on);
> > >> > #define CONF2_DATPOL (1 << 1)
> > >> >
> > >> > /* TI81XX specific definitions */
> > >> > -#define USBCTRL0 0x620
> > >> > -#define USBSTAT0 0x624
> > >> > +#define MUSB_USBSS_REV_816X 0x9
> > >> > +#define MUSB_USBSS_REV_814X 0xb
> > >> >
> > >> > /* TI816X PHY controls bits */
> > >> > #define TI816X_USBPHY0_NORMAL_MODE (1 << 0)
> > >> > diff --git a/drivers/usb/musb/musb_dsps.c
> > >> b/drivers/usb/musb/musb_dsps.c
> > >> > index 494772f..f7271c3 100644
> > >> > --- a/drivers/usb/musb/musb_dsps.c
> > >> > +++ b/drivers/usb/musb/musb_dsps.c
> > >> > @@ -115,9 +115,46 @@ struct dsps_glue {
> > >> > struct platform_device *musb; /* child musb pdev */
> > >> > const struct dsps_musb_wrapper *wrp; /* wrapper register
> > >> offsets */
> > >> > struct timer_list timer; /* otg_workaround timer */
> > >> > + u32 __iomem *usb_ctrl;
> > >> > + u8 usbss_rev;
> > >> > };
> > >> >
> > >> > /**
> > >> > + * musb_dsps_phy_control - phy on/off
> > >> > + * @glue: struct dsps_glue *
> > >> > + * @on: flag for phy to be switched on or off
> > >> > + *
> > >> > + * This is to enable the PHY using usb_ctrl register in system
> > >> control
> > >> > + * module space.
> > >> > + *
> > >> > + * XXX: This function will be removed once we have a seperate
> > driver
> > >> for
> > >> %s/seperate/separate
> > >> > + * control module
> > >> > + */
> > >> > +static void musb_dsps_phy_control(struct dsps_glue *glue, u8 on)
> > >> > +{
> > >> > + u32 usbphycfg;
> > >> > +
> > >> > + usbphycfg = __raw_readl(glue->usb_ctrl);
> > >>
> > >> How about using readl instead of __raw_readl here and below?
> > >> > +
> > >> > + if (on) {
> > >> > + if (glue->usbss_rev == MUSB_USBSS_REV_816X) {
> > >> > + usbphycfg |= TI816X_USBPHY0_NORMAL_MODE;
> > >> > + usbphycfg &= ~TI816X_USBPHY_REFCLK_OSC;
> > >> > + } else if (glue->usbss_rev == MUSB_USBSS_REV_814X)
> > {
> > >> > + usbphycfg &= ~(USBPHY_CM_PWRDN |
> > >> USBPHY_OTG_PWRDN
> > >> > + | USBPHY_DPINPUT |
> > USBPHY_DMINPUT);
> > >> > + usbphycfg |= (USBPHY_OTGVDET_EN |
> > >> USBPHY_OTGSESSEND_EN
> > >> > + | USBPHY_DPOPBUFCTL |
> > >> USBPHY_DMOPBUFCTL);
> > >> > + }
> > >> > + } else {
> > >> > + if (glue->usbss_rev == MUSB_USBSS_REV_816X)
> > >> > + usbphycfg &= ~TI816X_USBPHY0_NORMAL_MODE;
> > >> > + else if (glue->usbss_rev == MUSB_USBSS_REV_814X)
> > >> > + usbphycfg |= USBPHY_CM_PWRDN |
> > >> USBPHY_OTG_PWRDN;
> > >> > + }
> > >> > + __raw_writel(usbphycfg, glue->usb_ctrl);
> > >> only writel()?
> > >> > +}
> > >> > +/**
> > >> > * dsps_musb_enable - enable interrupts
> > >> > */
> > >> > static void dsps_musb_enable(struct musb *musb)
> > >> > @@ -363,11 +400,9 @@ static irqreturn_t dsps_interrupt(int irq,
> > void
> > >> *hci)
> > >> > static int dsps_musb_init(struct musb *musb)
> > >> > {
> > >> > struct device *dev = musb->controller;
> > >> > - struct musb_hdrc_platform_data *plat = dev->platform_data;
> > >> > struct platform_device *pdev = to_platform_device(dev-
> > >> >parent);
> > >> > struct dsps_glue *glue = platform_get_drvdata(pdev);
> > >> > const struct dsps_musb_wrapper *wrp = glue->wrp;
> > >> > - struct omap_musb_board_data *data = plat->board_data;
> > >> > void __iomem *reg_base = musb->ctrl_base;
> > >> > u32 rev, val;
> > >> > int status;
> > >> > @@ -395,8 +430,7 @@ static int dsps_musb_init(struct musb *musb)
> > >> > dsps_writel(reg_base, wrp->control, (1 << wrp->reset));
> > >> >
> > >> > /* Start the on-chip PHY and its PLL. */
> > >> > - if (data->set_phy_power)
> > >> > - data->set_phy_power(1);
> > >> > + musb_dsps_phy_control(glue, 1);
> > >> >
> > >> > musb->isr = dsps_interrupt;
> > >> >
> > >> > @@ -418,8 +452,6 @@ err0:
> > >> > static int dsps_musb_exit(struct musb *musb)
> > >> > {
> > >> > struct device *dev = musb->controller;
> > >> > - struct musb_hdrc_platform_data *plat = dev->platform_data;
> > >> > - struct omap_musb_board_data *data = plat->board_data;
> > >> > struct platform_device *pdev = to_platform_device(dev-
> > >> >parent);
> > >> > struct dsps_glue *glue = platform_get_drvdata(pdev);
> > >> >
> > >> > @@ -427,8 +459,7 @@ static int dsps_musb_exit(struct musb *musb)
> > >> > del_timer_sync(&glue->timer);
> > >> >
> > >> > /* Shutdown the on-chip PHY and its PLL. */
> > >> > - if (data->set_phy_power)
> > >> > - data->set_phy_power(0);
> > >> > + musb_dsps_phy_control(glue, 0);
> > >> >
> > >> > /* NOP driver needs change if supporting dual instance */
> > >> > usb_put_phy(musb->xceiv);
> > >> > @@ -460,6 +491,22 @@ static int __devinit
> > >> dsps_create_musb_pdev(struct dsps_glue *glue, u8 id)
> > >> > char res_name[10];
> > >> > int ret;
> > >> >
> > >> > + /* get memory resource for usb control register */
> > >> > + sprintf(res_name, "usb_ctrl%d", id);
> > >> > + res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
> > >> res_name);
> > >> Avoid getting resource by name.. With dt, you wont be able to do
> > >> those..
> > >
> > > When we are completely on DT then this would anyways go and we can
> > > get these resource data for each usb port from DT APIs.
> >
> > Even with dt, you will still get the resources using
> > platform_get_resource() API's.. So why not have it that way from the
> > beginning itself..
>
> Ok got it. We will post an updated patch.
Plalform_get_resource api works fine if we hardcode 3rd argument to 3+id for usb_cntrl register Since dsps_create_musb_pdev calls for each
wrp->instances.
static int __devinit dsps_create_musb_pdev(struct dsps_glue *glue, u8 id)
{
....
....
/* get memory resource for usb control register */
res = platform_get_resource(pdev, IORESOURCE_MEM, 3+id);
dev_err(dev,"Damodar :usb ctrl%d res=%x\n",id,res->start);
if (!res) {
dev_err(dev, "%s get mem resource failed\n", res_name);
ret = -ENODEV;
goto err0;
}
....
}
Damodar.
>
> Ajay
> >
> > Thanks
> > Kishon
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
