On Wed, 22 Dec 2010, Anoop P.A wrote:
> From: Anoop P A <anoop.pa@xxxxxxxxx>
>
> Adding chip specific code under quirk.
NAK. See below.
> Signed-off-by: Anoop P A <anoop.pa@xxxxxxxxx>
> ---
> drivers/usb/core/hub.c | 45 ++++++++++++++++++++++++++++++++++++++-----
> drivers/usb/core/quirks.c | 3 ++
> include/linux/usb/quirks.h | 3 ++
> 3 files changed, 45 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
> index 27115b4..4bff994 100644
> --- a/drivers/usb/core/hub.c
> +++ b/drivers/usb/core/hub.c
> @@ -3377,12 +3377,45 @@ static void hub_events(void)
> }
>
> if (portchange & USB_PORT_STAT_C_OVERCURRENT) {
> - dev_err (hub_dev,
> - "over-current change on port %d\n",
> - i);
> - clear_port_feature(hdev, i,
> - USB_PORT_FEAT_C_OVER_CURRENT);
> - hub_power_on(hub, true);
> + usb_detect_quirks(hdev);
This line is wrong. usb_detect_quirks() gets called only once per
device, when the device is initialized. Besides, you probably want to
use a hub-specific flag for this rather than a device-specific flag.
> + if (hdev->quirks & USB_QUIRK_MSP_OVERCURRENT) {
Also, it would be better to put this code in a separate subroutine
instead of indenting it so far.
> + /* clear OCC bit */
> + clear_port_feature(hdev, i,
> + USB_PORT_FEAT_C_OVER_CURRENT);
> +
> + /* This step is required to toggle the
> + * PP bit to 0 and 1 (by hub_power_on)
> + * in order the CSC bit to be
> + * transitioned properly for device
> + * hotplug
> + */
> + /* clear PP bit */
> + clear_port_feature(hdev, i,
> + USB_PORT_FEAT_POWER);
> +
> + /* resume power */
> + hub_power_on(hub, true);
> +
> + /* delay 100 usec */
> + udelay(100);
> +
> + /* read OCA bit */
> + if (portstatus &
> + (1<<USB_PORT_FEAT_OVER_CURRENT)) {
> + /* declare overcurrent */
> + dev_err(hub_dev,
> + "over-current change \
> + on port %d\n", i);
> + }
> + } else {
> + dev_err(hub_dev,
> + "over-current change \
> + on port %d\n", i);
> + clear_port_feature(hdev, i,
> + USB_PORT_FEAT_C_OVER_CURRENT);
> + hub_power_on(hub, true);
> + }
> +
> }
>
> if (portchange & USB_PORT_STAT_C_RESET) {
> diff --git a/drivers/usb/core/quirks.c b/drivers/usb/core/quirks.c
> index 25719da..59843b9 100644
> --- a/drivers/usb/core/quirks.c
> +++ b/drivers/usb/core/quirks.c
> @@ -88,6 +88,9 @@ static const struct usb_device_id usb_quirk_list[] = {
> /* INTEL VALUE SSD */
> { USB_DEVICE(0x8086, 0xf1a5), .driver_info = USB_QUIRK_RESET_RESUME },
>
> + /* PMC MSP over current quirk */
> + { USB_DEVICE(0x1d6b, 0x0002), .driver_info = USB_QUIRK_MSP_OVERCURRENT },
> +
This implementation is completely wrong. It applies to all USB-2.0
root hubs in Linux, not just the PMC MSP.
> { } /* terminating entry must be last */
> };
>
> diff --git a/include/linux/usb/quirks.h b/include/linux/usb/quirks.h
> index 3e93de7..97ab168 100644
> --- a/include/linux/usb/quirks.h
> +++ b/include/linux/usb/quirks.h
> @@ -30,4 +30,7 @@
> descriptor */
> #define USB_QUIRK_DELAY_INIT 0x00000040
>
> +/*MSP SoC onchip EHCI overcurrent issue */
> +#define USB_QUIRK_MSP_OVERCURRENT 0x00000080
> +
> #endif /* __LINUX_USB_QUIRKS_H */
>
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
