[PATCH v2] USB: ehci-mxc: Setup portsc register prior to accessing OTG viewport

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



In order to read/write to the i.MX OTG viewport register it is necessary to setup
the PORTSCx register first. 

By default i.MX OTG port is configured for USB serial PHY. In order to use a ULPI PHY
the PORTSCx register needs to be configured properly.

Original code accessed OTG viewport without configuring PORTSCx and this caused ULPI
read/write to fail.

Tested on a MX31PDK board with a ISP1504 transceiver:

ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver                      
mxc-ehci mxc-ehci.0: initializing i.MX USB Controller                           
ULPI transceiver vendor/product ID 0x04cc/0x1504                                
Found NXP ISP1504 ULPI transceiver.                                             
ULPI integrity check: 

Signed-off-by: Fabio Estevam <fabio.estevam@xxxxxxxxxxxxx>
---
Changes since v1:
-removed second call to ehci = hcd_to_ehci(hcd);

 drivers/usb/host/ehci-mxc.c |   22 +++++++++++++++-------
 1 files changed, 15 insertions(+), 7 deletions(-)

diff --git a/drivers/usb/host/ehci-mxc.c b/drivers/usb/host/ehci-mxc.c
index bce8505..1a730bf 100644
--- a/drivers/usb/host/ehci-mxc.c
+++ b/drivers/usb/host/ehci-mxc.c
@@ -65,12 +65,6 @@ static int ehci_mxc_setup(struct usb_hcd *hcd)
 
 	ehci_reset(ehci);
 
-	/* set up the PORTSCx register */
-	ehci_writel(ehci, pdata->portsc, &ehci->regs->port_status[0]);
-
-	/* is this really needed? */
-	msleep(10);
-
 	ehci_port_power(ehci, 0);
 	return 0;
 }
@@ -125,7 +119,8 @@ static int ehci_mxc_drv_probe(struct platform_device *pdev)
 	int irq, ret;
 	struct ehci_mxc_priv *priv;
 	struct device *dev = &pdev->dev;
-
+	struct ehci_hcd *ehci;
+
 	dev_info(&pdev->dev, "initializing i.MX USB Controller\n");
 
 	if (!pdata) {
@@ -200,6 +195,19 @@ static int ehci_mxc_drv_probe(struct platform_device *pdev)
 	ret = mxc_initialize_usb_hw(pdev->id, pdata->flags);
 	if (ret < 0)
 		goto err_init;
+
+	ehci = hcd_to_ehci(hcd);
+
+	/* EHCI registers start at offset 0x100 */
+	ehci->caps = hcd->regs + 0x100;
+	ehci->regs = hcd->regs + 0x100 +
+	    HC_LENGTH(ehci_readl(ehci, &ehci->caps->hc_capbase));
+
+	/* set up the PORTSCx register */
+	ehci_writel(ehci, pdata->portsc, &ehci->regs->port_status[0]);
+
+	/* is this really needed? */
+	msleep(10);
 
 	/* Initialize the transceiver */
 	if (pdata->otg) {
-- 
1.6.0.4

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux