Re: [PATCH] usb: chipidea: fix ci_irq for role-switching use-case

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 20-07-01 08:32:22, Philippe Schenker wrote:
> On Wed, 2020-07-01 at 02:52 +0000, Peter Chen wrote:
> > On 20-06-30 11:59:49, Philippe Schenker wrote:
> > > On Tue, 2020-06-30 at 00:43 +0000, Peter Chen wrote:
> > > > On 20-06-29 10:04:13, Philippe Schenker wrote:
> > > > > On Mon, 2020-06-29 at 07:26 +0000, Peter Chen wrote:
> > > > > > On 20-06-26 13:03:11, Philippe Schenker wrote:
> > > > > > > If the hardware is in low-power-mode and one plugs in device
> > > > > > > or
> > > > > > > host
> > > > > > > it did not switch the mode due to the early exit out of the
> > > > > > > interrupt.
> > > > > > 
> > > > > > Do you mean there is no coming call for role-switch? Could you
> > > > > > please
> > > > > > share
> > > > > > your dts changes? Try below patch:
> > > > > 
> > > > > Here are my DTS changes:
> > > > > 
> > > > > diff --git a/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
> > > > > b/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
> > > > > index 97601375f2640..c424f707a1afa 100644
> > > > > --- a/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
> > > > > +++ b/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
> > > > > @@ -13,6 +13,13 @@
> > > > >                 stdout-path = "serial0:115200n8";
> > > > >         };
> > > > >  
> > > > > +       extcon_usbc_det: usbc_det {
> > > > > +               compatible = "linux,extcon-usb-gpio";
> > > > > +               id-gpio = <&gpio7 14 GPIO_ACTIVE_HIGH>;
> > > > > +               pinctrl-names = "default";
> > > > > +               pinctrl-0 = <&pinctrl_usbc_det>;
> > > > > +       };
> > > > > +
> > > > >         /* fixed crystal dedicated to mpc258x */
> > > > >         clk16m: clk16m {
> > > > >                 compatible = "fixed-clock";
> > > > > @@ -174,6 +181,7 @@
> > > > >  };
> > > > >  
> > > > >  &usbotg1 {
> > > > > +       extcon = <&extcon_usbc_det>, <&extcon_usbc_det>;
> > > > 
> > > > If you have only ID extcon, but no VBUS extcon, you only need to
> > > > add only phandle, see dt-binding for detail please.
> > > 
> > > You where right again! Thanks, this actually solves the RNDIS issue
> > > for
> > > our colibri-imx7 board:
> > > 
> > > +       extcon = <0>, <&extcon_usbc_det>;
> > > 
> > > Howevever on this iMX7 board we have VBUS hooked up to the SoC,
> > > that's
> > > why it works only with ID.
> > > 
> > > On Colibri-iMX6ULL we do not have VBUS hooked up.
> > 
> > So, there is no any events for connecting to Host? If it is, the
> > workaround for this board is disable runtime pm. And you only need to
> > write one extcon phandle for ID since you have external event for ID,
> > but no event for VBUS. ID event is not the same with VBUS, for
> > example,
> > if you plug cable into host, you will not get the ID event, you could
> > only get VBUS event if there is an event (eg, through GPIO) for it.
> > 
> > Peter
> 
> No we don't have extra Host events. We have one GPIO, if it is high USB
> should be in gadget mode and if the GPIO is low USB should be in host
> mode.
> 
> Is there no way we can achieve this on mainline without disabling
> runtime PM?
> 

At least I think so, since you don't have any events to let the
SW know you connects to host if the controller is in low power mode.

Peter

> Philippe
> 
> > 
> > > So device/host
> > > switching works only with 'extcon = <&extcon_usbc_det>,
> > > <&extcon_usbc_det>;' but then RNDIS and also a normal thumb-drive
> > > does
> > > not work. How could I work around this fact? A dummy-gpio that would
> > > always read "high" for vbus would be a solution for me.
> > > 
> > > Philippe
> > > 

-- 

Thanks,
Peter Chen



[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux